Question about Cars & Trucks
Done timing belt of 99 grandeur and now wont start. need help please and if anyone got a pic pleas.
A Chilton/Haynes repair manual that covers your car will have the needed diagrams and firing order.
Posted on Nov 14, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Firstly if the belt went you probably have bent valves. However if you want to assemble and see remove cam belt covers,remove crank pulley (could be tricky if you don't have an air tool ) remove tappet cover ( you may have to remove the throttle body to do this) Get some flat bar approx. 6mm thick and 400 to 500 mm long. You will see that on the gearbox side of the cams there are slots in the end. Remove the plugs and put a screw driver ( long ) down the hole, any one, and turn the crank untill the piston is roughly half way down the bore. Turn the cams until the plate will sit on the head and slot into the cams thus locking them. The slots are offset so you will have to play around until the plate slides in easy. Then loosen the cam gears untill you can spin them by hand, but not so loose that they are falling off. Put your long screwdriver or preferably a dial guage with extensions into no 1 plug hole turn the engine untill the piston is right at the top. Loosen the tensioner and push it back against the spring and lock it fit the new belt right to left then let the tensioner go. Check play on longest side of belt it should move about 6mm. lock the tensioner. Tighten the cam pulleys and remove plate. turn the engine one full turn clockwise and check belt tension- adjust if neccessary. turn one full turn again and make sue plate slides in when no. 1 piston is on top. Then do a compression test to see if you have bent valves. If the compression test is ok. reassemble and drive away. If not (the exhaust valves are normally bent) you are half way to taking the head off. In which case contact me and I will walk you through it. Good luck Shaun
Posted on Jun 10, 2008
SOURCE: 99 ford ranger timing belt
Using the same 13mm socket, remove the bolt that you found under the a/c compressor. Look down and to the right of the bolt that you just removed, and you will see two more bolts. Both are 13mm. Easiest way that I found was to go under the driver side tire well, and use 3/8 extensions to reach the two bolts. Once removed, the bracket and the power steering pump should be moved to the driver's side of the frame, and the a/c placed on top of the p/s assy.
Remove the bolts (6mm) that hold the timing belt cover in place. Gently work your way around the cover, and push the tabs in to remove the cover.
Use an impact wrench and 7/8 SAE socket to remove the crankshaft pulley. A SOCKET WRENCH WILL NOT WORK. Once removed, gently tap the pulley with a 2x4 (yes the wooden board) to remove. If you have a gear puller, use that. I don't own one.
Remove the old belt. Now for the alignment. Crank - sprocket on bottom. Use the bolt you removed, and a ½ drive wrench, with the 7/8 socket to turn the crank. Once the keyway is at high noon, leave it alone. Next, move the oil pulley sprocket until the diamonds are aligned. This should put the oil pulley at high noon, also. The camshaft should have a diamond and a triangle. The diamond should go to high noon, and the triangle should align with a triangle on the plastic behind the sprocket. YOU SHOULD REALLY CONSIDER CLEANING THE ENTIRE AREA BEFORE ALIGNING THE SPROCKETS. You cannot align the camshaft without locating the two index (triangle and diamond) marks.
You will also notice a tensioner for the timing belt. You will need to loosen the tentioner with a 13mm and 17mm wrenches. Loosen, then use a cheeter bar bar to move the tentioner over. Lock in place by tightening the tentioner bolts. Place the belt on the crankshaft, move to the oil pulley, then to the cam pulley. Release tentioner, then check the alignment. If correct, reverse the above removal plan, and you should be good.
Don't buy the Haynes manual. I fought with the instructions for this project, and the picture for the timing belt project doesn't show the two indexes for the cam sprocket.
Also, while you are doing this, you should replace the antifreeze if you haven't in the past two years.
Best of luck.
Posted on Jul 13, 2008
SOURCE: 2002 Toyota solar timing belt
Chilton or Haynes manual will have all the pics you can stand on this, they can be bought at most auto parts stores, also check your local library they will surprise you with how many repair manuals they have
Posted on Apr 01, 2009
SOURCE: need to install belt
i made this with paint. hope it helps. typically on a bmw the belt goes between the water pump and crank pulley to the tensioner; if this is a 99 to 06 ish 3 series and some 5 s you will be good
Posted on May 03, 2009
this is a job for a qualified repair shop. I do not recommend you to do it. If you want to do it, buy a manual, prefer a manual from the dealer. The money you save will more than pay for it.
Posted on Oct 11, 2009
Tips for a great answer:
Aug 31, 2014 | 2005 Hyundai Grandeur
Apr 22, 2017 | 1989 Nissan Stanza
Welcome to FIxYa.com
Need the year and model and size as in liter engine in order to look this up for you to send pic and info. Engine number does not work in Alldata, Lee
Thank you for using FixYa.com
Regards, Lee Davidian
Dec 30, 2010 | Toyota RAV4 Cars & Trucks
Sep 06, 2010 | 2004 Dodge Caravan
Jan 18, 2009 | 1997 Volkswagen Jetta
Jul 04, 2008 | 1991 Toyota Tercel
Oct 17, 2017 | Cars & Trucks
38 people viewed this question
Usually answered in minutes!