Question about 2005 Chrysler Sebring Sedan

2 Answers

I have a weak sounding horn?

The horn on my car can not be as strong a if was when I first bought it what would cause the loss of sound?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chrysler Master
  • 44,379 Answers

Hons suffer from rust at the horn coil and dirt at the points of the coil. Normally they are not serviceable so a replacement horn is the fix.

Posted on Nov 14, 2014

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Check it for mice nests?

Posted on Nov 15, 2014

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2004 chrysler sebring horn...

sounds like only 1 of your 2 horns is working - up under hood near center in frt of radiator-or on 1 side down in front by wheel well horns are located

Posted on May 23, 2009

emissionwiz
  • 76649 Answers

SOURCE: Van won't start. Just makes a clikcing noise. Horn sounds weak.

THIS IS CAUSED BY A DEFECTIVE STARTER MOTOR SOLENOID, REMOVE AND REPLACE THE STARTER OR JUST REPLACE THE SOLENOID ON TOP OF THE STARTER IF YOU CAN BUY IT SEPERATE.

Posted on Jul 04, 2009

  • 7353 Answers

SOURCE: my 2003 Chrysler pt cruiser's horn is really weak.

replace the horn

Posted on Oct 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bought a 1992 acura vigor and found horn fuse missing. when I replaced the fuse alarm goes off and constantly sounds. how do I stop it? I've read that there's a relay somewhere under the hood


horn relay located on the right side kick panel,you will see a row of relays,if horn relay is okay, more likely your horn control pad has a short inside causing horn button contacts to stick causing horn to keep blowing.

Oct 01, 2012 | 1992 Acura Vigor

1 Answer

1997 saturn sl1 horn sounds really weak, i replaced the fuse cause it was blown. was a 10v?(red fuse with a 10 on it). Now it works but barely makes any noise. how do i fix this? do i need to replace the...


the problem is the horn diaphram is weak and you will have to replace the horn assembly.the numbers on the fuses is the amp rating of the fuse not voltage for your information.

Oct 17, 2011 | 1997 Saturn SL

1 Answer

HOrn makes a noise but very weak noise. should i replace the horn or horn relay?


Run a thick wire straight from the battery to the positive terminal of the horn. If the horn sounds normal, replace the relay. If the horn is still weak, locate the adjustment screw and play with that to try improve the tone, if that does not work or if there is no screw, replace the horn,

Aug 09, 2011 | 1996 Jeep Grand Cherokee

1 Answer

My horn became weak and doesn't work at all now, what causes this?


Locate the horn and check for corrosion where it mounts.
It must have a good clean ground to operate properly.
Sounds like the ground connection was slowly deteriorating to the point the connection is lost

Jan 24, 2011 | 2003 Nissan Xterra

1 Answer

01 grand am. Horn sounds really weak. What could be the cause?


The horn itself occasionally they too go bad and need to be replaced, however on occasions the electrical connectors to the horn assembly may have a bit of corrosion on the positive and ground contacts causing the weak feature you describe.

Aug 12, 2010 | 2001 Pontiac Grand Am SE

1 Answer

95 olds cutluss cieara horn dont work. horn sounded weak when it was dien 4 mths ago. then when i pressed it last it amped out the horn and radio. hasnt work since. cheeked fuses


Check that the horn itself is not worn out. If it's not sounding when grounding out, or it has a history of being faint in volume, then replace the horn.

Horns do go bad over time due to atmospheric moisture causing the contacts to corrode.

Aug 11, 2010 | 1995 Oldsmobile Cutlass Ciera

1 Answer

2004 chrysler sebring horn...


sounds like only 1 of your 2 horns is working - up under hood near center in frt of radiator-or on 1 side down in front by wheel well horns are located

May 23, 2009 | 2004 Chrysler Sebring

1 Answer

Horn sounds weaker than usual


There are two horns on this vehicle. Check to make sure they are grounded properly, and if you have a volt meter, disconnect the horn wire, have someone push the horn button while you check the voltage on the wire. You should get at least 12 volts. If the horn has a good ground, and is getting the required voltage, then you probably have a bad horn. Disconnect one at a time, and see how loud each of them are. This should help determine which one, if not both is causing the problem.

Mar 26, 2009 | 2003 Nissan Altima

1 Answer

Weak sounding horn when cold


If you can remove the horn, spray some wd40 or other solvent into it and turn it so that the solvent will run into the center. Usually that will free it up. Or, just get another from a junkyard!

Jan 04, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Horn stopped blowing


Sounds like you may have corroded terminals on the horn itself.

Find the horn in the engine compartment - remove the wire connected to it - clean the spade terminal with some sand paper and push the terminal back on. If that doesn't work you may need to remove the horn from the car and clean up the earth connection, i.e. where the horn is attached to the body work of the car to get a good electrical contact.

Aug 22, 2008 | 2000 Ford Focus

Not finding what you are looking for?
2005 Chrysler Sebring Sedan Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...