Question about Cars & Trucks

1 Answer

Does the turn signal switch operate wind shield wipers 2001 f 150 7 wire need diagram

7 wire turn signal switch connector

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 40,701 Answers

This is not a normal application as with washers/wipers there are multiple operations on the stalk ( up for 1 swipe- neutral /off-down 1 intermittent speed -down again 2 intermittenent wipes --3 on all the time Twist the knob of time period of swipes during intermittent swipes.. Turn switches indicate l or r ( up or down) and back to the wheel high or low beam for the head lights or twist the knob for off parks and headlights.

Posted on Nov 13, 2014

Testimonial: "Thanks, bill my ? turn signal connector wires came loose only then wiper stop working + brake lights turn sig was searching for any help for wire diagram to get thing working again 2001 f150 its 7 wires, Thanks for any help"

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: wind shield wipers stop in center of window

Sounds like a linkage (wiper transmission) problem. But, put an external ground wire to the wiper motor first and see if they work then.
Also many wipers have a fastening nut on the wiper arm where it attaches to the stub that goes through the body. These may have loosened and gone out of adjustment. If so, loosen them and re-position arms, then tighten them down.

Posted on Dec 16, 2008

  • 740 Answers

SOURCE: fuse box diagram 98 honda civic

Get a fuse tester you don't have to pull every fuse to check

Posted on Dec 19, 2008

MrScary66613
  • 1990 Answers

SOURCE: 2001 dodge intrepid wind shield wipers not working

There is a Fuse for the Wipers on the Box inside the Car. There actually could be one in the Relay Fuse Box under the Hood also. This box Shoud be on the Drivers Side up torwards the Firewall of the Car.

Posted on Jan 25, 2009

  • 2 Answers

SOURCE: 1999 vw beetle. blinkers, wind shield wipers not working.

check the electrical part of your ignition switch . this is common to burn out and is easy and inexpensive to fix .does not require anything to be done to the mechanical part of the switch and key.

Posted on Jul 16, 2009

  • 1 Answer

SOURCE: wind shield wipers stopped working, wiper motor

I have the same problem with my 1989 Dakota. I found a part: A-1 CARDONE Part # 40387 which is listed as a Wiper Motor. Is that the same thing?

Posted on Jan 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why do my wipers on my 1998 chevy lumina only work non hig


Do you know how to do electrical testing ? Here is diagnostic trouble flow chart .You will need a wiring diagram . Go to http://www.bbbind.com/free_tsb.html free wiring diagrams . You can see basic automotive trouble shooting videos on you tube if you are not familiar with this .
Wipers Low Mode Inoperative, High Mode Operates

2
Disconnect wiper motor connector C1.
Turn the ignition switch ON.
Set the wiper switch to LO.
Connect a test light from wiper motor connector C1, terminal B, to ground.
Is the test light on?
--
YES - Go to Step 6
NO - Go to Step 3

3
Inspect for a poor connection or an open in CKT 91.
Is a poor connection or an open present?
--
YES - Go to Step 4
NO - Go to Step 5

4
Repair the poor connection or the open in CKT 91.
Is the repair complete?
--
Go to Wiper/Washer System Check
--

5
Replace the wiper/washer switch. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle in Steering Wheel and Column -Tilt.
Is the replacement complete?
--
Go to Wiper/Washer System Check
--

6
Connect a test light from wiper motor connector C1, terminal C, to ground.
Is the test light on?
--
YES - Go to Step 10
NO - Go to Step 7

7
Inspect for a poor connection or an open in CKT 95.
Is a poor connection or an open present?
--
Go to Step 9
Go to Step 8

8
Repair the poor connection or the open in CKT 95.
Is the repair complete?
--
Go to Wiper/Washer System Check
--

9
Replace the wiper/washer switch. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle in Steering Wheel and Column -Tilt.
Is the replacement complete?
--
Go to Wiper/Washer System Check
--

10
Inspect for continuity between wiper motor connector C1, terminal A, and connector C2, terminal B, using a J39200.
Is continuity present?
--
Go to Step 12
Go to Step 11

11
Repair the open in CKT 196.
Is the repair complete?
--
Go to Wiper/Washer System Check
--

12
Inspect for a poor connection to the wiper motor at connector C1.
Is a poor connection present?
--
Go to Step 13
Go to Step 14

13
Repair the poor connection at wiper motor connector C1.
Is the repair complete?
--
Go to Wiper/Washer System Check
--

14
Replace the wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the replacement complete?
--
Go to Wiper/Washer System Check
--

Feb 29, 2016 | Cars & Trucks

1 Answer

Why is my windshield wipers running in the off position, it's like they are running in the intermittent position, but it's in the off position.


When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Schematic Reference: Wiper/Washer Schematics


1

Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Symptoms - Wiper/Washer Systems

2

  1. Turn the ignition ON.
  2. Turn the windshield wiper/washer switch OFF.
Are the windshield wipers always on?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

Disconnect the windshield wiper/washer switch connector.
Are the windshield wipers always on?
Go to Step 4 if yes
Go to Step 7 if no

4

  1. Disconnect the windshield wiper motor connector.
  2. Test the windshield wiper switch signal 1 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 5

5

Test the windshield wiper switch signal 2 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 6

6

Test the windshield wiper motor high speed circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 9

7

Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 8

8

Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement - On Vehicle in Steering Wheel and Column.
Is the repair complete?
Go to Step 11
--

9

Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

10

Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the repair complete?
Go to Step 11
--

11

Operate the system in order to verify the repair.
Did you correct the condition?
The Wiper / Washer System consists of the following components:
?€¢
Windshield wiper / washer switch


?€¢
Windshield wiper system module / motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
Instrument panel cluster (IPC)


?€¢
ACC 15-amp fuse


?€¢
WSW 30-amp fuse

Jan 04, 2016 | 2002 Pontiac Bonneville

1 Answer

My windshield wipers on my 2000 Pontiac Montana won't stop as soon as I turn it on they start going I have tried turning it off of course but they just keep going


The switch is bad or the wiper motor cover ,electronics !
  1. Turn the ignition switch to RUN.
  2. Turn the wiper switch to OFF.
  3. Disconnect the wiper/washer switch connector C201.
Do the wipers park? yes or no ?
if yes Replace the wiper/washer switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle .
if no
Measure the voltage from connector C201 (vehicle side), terminal E2, to ground with a DMM.
Does the voltage measure greater than the specified value?
1.0 V yes or no ?
Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .
Did you complete the replacement?
--
Go to Step 9
--

6

  1. Reconnect the wiper/washer switch connector C201.
  2. Disconnect the wiper motor connector.
  3. Measure the voltage from the wiper motor connector, terminal D, to ground with a digital voltmeter.
Does the voltage measure greater than the specified value?
1.0 V
Go to Step 8
Go to Step 7

7

Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .
Did you complete the replacement?
--
Go to Step 9
--

8

Repair the short to voltage in CKT 113. Refer to Wiring Repairs in Wiring Systems.
Did you complete the repair?
--
Go to Step 9
--

9

Operate the system in order to verify the repair.
Did you correct the condition?
--
System OK
Go to Wiper/Washer System Check



if yes

Apr 20, 2015 | 2000 Pontiac Montana

2 Answers

I have a 2007 mustang an the wipers wont turn off I had 2 pull the fuse to turn them off can u help me


The windshield wiper motor is a smart wiper motor with an integrated electronics module. The internal components of the motor are the high/low relay, washer pump relay, and the run/park relay and associated electronics.
The windshield wiper motor receives its inputs from the windshield wiper/washer switch. These signals are ground reference signals. When the switch is placed in different positions, various input signals are selected and sent through circuits to the motor. The windshield wiper motor module identifies these selected input signals and activates the motor to the selected function.!
Your probably going to need a new wiper motor ! ! ! But you should always test before replacing parts !
Visual Inspection Chart Mechanical Electrical
  • Windshield washer pump hoses
  • Windshield wiper mounting arm and pivot shaft
  • Bussed electrical center (BEC) fuse 10 (30A)
  • Smart junction box (SJB) fuse 3 (10A)
  • Circuitry
  • Windshield wiper motor
  • Windshield washer pump
  • Windshield wiper/washer switch
  • The wipers stay on continuously
  • Circuitry
  • Windshield wiper motor
  • Windshield wiper/washer switch
  • Go To Pinpoint Test C .
PINPOINT TEST C: THE WIPERS STAY ON CONTINUOUSLY s6b~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use the correct probe adaptor(s) when making measurements. Failure to use the correct probe adaptor(s) may damage the connector.
Test Step Result / Action to Take C1 CHECK THE WINDSHIELD WIPER/WASHER SWITCH
  • Key in OFF position.
  • Disconnect: Windshield Wiper/Washer Switch C2137.
  • Carry out the windshield wiper/washer switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Does the windshield wiper/washer switch pass the component test?
Yes
GO to C2 .

No
INSTALL a new windshield wiper/washer switch. REFER to Wiper/Washer Switch in this section. C2 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR A SHORT TO GROUND
  • Disconnect: Windshield Wiper Motor C125.
  • Measure the resistance between the windshield wiper motor C125, harness side and ground as follows:

    Windshield Wiper Motor C125 Pin Circuit C125-10 56 (DB/OG) C125-11 58 (WH) C125-1 63 (RD) C125-9 61 (YE/RD)

    s6b~tr~en~file=n0011980.gif~gen~ref.gif
  • Are the resistances greater than 10,000 ohms?
Yes
GO to C3 .

No
REPAIR the circuit(s). TEST the system for normal operation. C3 CHECK FOR CORRECT WINDSHIELD WIPER MOTOR OPERATION
  • Disconnect all the windshield wiper motor connectors.
  • Check for:
    • corrosion.
    • pushed-out pins.
  • Connect all the windshield wiper motor connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present?
Yes
INSTALL a new windshield wiper motor. REFER to Wiper Motor in this section. TEST the system for normal operation.

No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
You

Feb 20, 2015 | 2007 Ford Mustang Coupe

1 Answer

? turn signal connector wires came loose only then wiper stop working + brake lights turn sig was searching for any help for wire diagram to get thing working again 2001 f150 its 7 wires, Thanks for a


Go to alldatadiy.com and buy the wiring for your vehicle. Other wise go to the junk yard and cut the plugs and wires out of an exact vehicle. This is the only two ways you will fix it. Exact diagrams or exact plugs and switches.

Nov 16, 2014 | Cars & Trucks

1 Answer

My wipers stay on when the ignition is powered on and I loose my turn signals


I am thinking the turn signal switch has failed. I believe all these things are on the same lever. May be worth a try.

May 20, 2012 | 2009 Dodge Journey

2 Answers

Front wind shield wipers not turning off


We do not have this model in the USA so have no tech support for it. Sorry

May 16, 2012 | 2007 Ford Ka

1 Answer

I HAVE A 200 MERCURY COUGAR AND MY WIND SHIELD WIPERS, TURN SIGNALS, AND HAZARD LIGHTS STOPPED WORKING WHAT COULD IT BE


first check all panel and underhood fuses and if all o.k you need a multifunction switch which operates all of mentioned componants.

Jan 27, 2009 | 2000 Mercury Cougar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...