Question about 2006 Chrysler 300

1 Answer

Reverse lights are on when I put the headlights on chrysler 300 2006

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 22 Answers

Try moving your shifter past reverse a few times. There's switch when it's on reverse that might be sticking.

Posted on Nov 13, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My headlights go off as soon as I put my car in drive or reverse. If I turn on a blinker, they all go off. What the heck can I do to have headlights and tail lights in my car?

This will need to be diagnosed by a hands on mechanic rather than over the internet, I would suggest the dealership as they will have better access to information from the manufacturer than other mechanics.

Mar 22, 2017 | 2006 Chrysler PT Cruiser

1 Answer

Have a 87-88 dodge Dakota and the reverse lights will not go off when the lights are on, how do I fix this?

Do the reverse lights operate normally with the headlights off? The reverse lights are on an entirely different circuit than than the park/headlights. In order for them to come on with the park/headlights, there will have to be a short to power on the circuit. Will the park lights come on if the vehicle is put in reverse with the headlight switch off? Look for shorted/corrodded wiring in the rear taillight circuit and connector plugs. Green corrossion in/around any plug or wiring is a sure sign of a problem

Jan 21, 2016 | Dodge Cars & Trucks

1 Answer

The reverse lights stay on when I put the headlights on how do I fix this

install a new switch in the tranny, or into the center console of the cabin (depending on it's actual location ) the old one is either faulted all together or soon will be.

Nov 13, 2014 | 2006 Chrysler 300

1 Answer

I have a 2005 Chrysler town and country. I went to put my foot on the brake to put it into drive and my speedometer gas and everything went blank and the park drive reverse neutral and all that went out...

I would pull the rear brake light bulbs and top 3rd brake light wire first to check for a shorted bulb.Do you have trailer wiring?That can be a source of shorts too.Next would be a "short tester" be used on the brake light wiring.

Jul 09, 2017 | Cars & Trucks

1 Answer

Are head light easy to get to to change or do you have to remove lots of stuff

Locate the 3 screws that hold the headlight housing to the vehicle. Remove the 3 screws and slide the housing out out of the alignment tabs(may require some wiggling). The bulb goes in the housing at the back. Turn the lock ring, remove the old bulb, disconnect the bulb, put the new bulb in and reverse this order.

Jan 18, 2011 | 2005 Chrysler Town & Country

1 Answer

Is there a headlight wiring loom for a chrysler voyager, or do I have to replace the entire headlight unit

Loom? The 1990 Models were mixed. Before that the whole head light was replaced. In the 2000 year models you need to locate the collar on the back of the head light, turn it counter clockwise and remove the bulb from the headlight assembly. Unplug bulb and replace then reverse the process to install. If you use the little machine that Walmart usually keep near the replacement bulbs in the Automotive section you can get verification of what type you have if your not sure. You will need to know the Year and model of your vehicle.

Oct 15, 2010 | Chrysler Voyager Cars & Trucks

1 Answer

Replacing the passenger side headlight

There are 2 plastic retainers behind the headlight. Lift these up and out and pull out light. Bulbs are twist type twist and pull. Replace putting the plastic moded headlight nubs back in headlight mount panel and putting clips over them and pushing down.

Nov 09, 2009 | 1999 Chrysler Town & Country

2 Answers

I am trying to remove the headlight lens to replace the bulb on my 1996 chrysler LHS. I can't remove the lens.

head light assembly has four ball and sockets to hold it in place ,grab a hold and pull straight foward ,put greese on balls win putting back in to make it easier next time...

Sep 18, 2009 | 1996 Chrysler LHS

1 Answer

Drivers side reverse light on while i drive.

Your car has rear fog lights. The rear light that you see come on with your headlights is your rear fog light. The light in your dash is the rear fog light indicator. To turn off your rear fog lghts push your headlight switch in half way. To turn off your front fog lights push in all of the way.

Jan 13, 2009 | 1999 BMW 328 Series

Not finding what you are looking for?
2006 Chrysler 300 Logo

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides