Question about Mazda B-Series Truck

1 Answer

<!-- from fixya rte -->How to replace fuel pump 2000 b40000 mazda - B-Series Truck Mazda Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 424 Answers

Here is a video showing the process of replacing the fuel pump.
How to Install Fuel Pump E2263S in 1999 Ford Ranger and 1998 1999 Mazda...

Posted on Nov 13, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

al-sultan
  • 250 Answers

SOURCE: Instructions to replace water pump on 2000 Mazda Precidia

1. Depressurize and drain the cooling system. 2. Loosen the alterantor adjustment and remove the belt.
3. Remove the water pump pulley.
4. Remove all the timing belt covers.
5. Loosen the timing (camshaft) belt tensioner and slip the timing belt off the camshaft toothed pulley (ensure you do not move the positon of the camshaft)
6. Unbolt the lower radiator hose fitting and heater retrun pipe.
7. Unbolt the waterpump from the block (5 bolts).
8. Remove all traces of the old gasket before mounting the new pump (Permatex spray on gasket remover works well).
9. Install the new pump and reassemble in reverse order to above.

Posted on Jul 31, 2009

rcampsr
  • 90 Answers

SOURCE: Do you know where or if a 2000 Mazda 626 has a

Hello, I am going to make a few assumptions here. The vehicle has an electric fuel pump and you replaced it. The vehicle has fuel injection. The engine is actually cranking, just not starting, when you say "car still won't crank". You are getting fire to the spark plugs at the plug ends. You checked the fuel pump for power at the pump. No power, then you back traced the wire to the fuse block and checked the fuse to see if it was blown. If the fuse is good back trace the power to the ignition switch and/or ECM for power. You have power at the pump, check the ground and make sure it is connected properly. Will the pump run when someone turns the key on? Pump runs, check fuel manifold for pressure. No pressure, check the fuel filter for blockage, or replace it. Fuel pump doesn't run, new replacement pump is defective. There is usually some type of control module for the fuel pump on fuel injected vehicles. Good Luck, RAC

Posted on Apr 18, 2009

localwonder
  • 6784 Answers

SOURCE: how do i replace the fuel pump in my 1993 mazda 626 2.5

1. Relieve the fuel pressure and disconnect the negative battery cable.

2. If not already removed, depress the clips on each end of the rear seat cushion and remove the cushion.

3. If not already done, detach the electrical connector from the fuel pump/sending unit.

4. Remove the attaching screws from the fuel pump/sending unit access cover and remove the cover.

5. Disconnect the fuel supply and return hoses from the fuel pump/sending unit.

6. Remove the attaching screws and the fuel pump/sending unit from the fuel tank.

7. Detach the sending unit electrical connector, remove the sending unit attaching nuts and remove the sending unit from the fuel pump assembly.



To install:

1. Attach the sending unit to the fuel pump assembly and install the nuts. attach the sending unit electrical connector.

2. Install the fuel pump/sending unit into the fuel tank with a new gasket and install the mounting screws.

3. Connect the fuel supply and return lines.

4. Install the access cover and the mounting screws.

5. Attach the sending unit electrical connector.

6. Position the rear seat cushion over the floor, making sure to align the retaining pins with the clips. Push down firmly until the two retaining pins are locked into the rear seat retaining clips.

7. Connect the negative battery cable, start the engine and check for proper system operation and for fuel leaks.

Posted on Jun 13, 2009

wracefans24
  • 1985 Answers

SOURCE: How to Replace a Fuel pump on a 2000 Mazda 626

yes it isn't that much if you buy them.they slide inside the coupler and release the line.

Posted on Dec 27, 2009

Testimonial: "Thank you didn't know if there was a tool for this."

  • 224 Answers

SOURCE: fuel pump replacement 2002 mazda miata

The fuel pump is in the fuel tank. You may be able to access the fuel tank by removing your bottom rear seat cushion. If no access there you must remove the fuel tank. If you have to remove the tank and it is mostly full you should siphon out as much fuel as you can into appropriate containers.

Posted on Aug 23, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I tell if fuel pump is bad on a 2000 Mazda millennia super charged car and location and replacement...someone said I could bypass with an in line fuel pump


Go under hood.. and locate your fuel rail. And find the pressure release valve. Turn key to on position and depress the valve and it should spray gas... if not check.. fuse and relay for fuel pump... pump is in the tank..

Sep 01, 2016 | 2000 Mazda Millenia

1 Answer

2000 mazda protege 1.6 liter dx..... I have no power to my fuel pump I have replaced the pump and relays and fuses are good... Where is my inertia switch on this vehicle


No inertia switch on the Prot?g?. Ford thing. Not used by Mazda. No voltage to the Red with white stripe wire at fuel pump?

Sep 18, 2015 | Mazda Cars & Trucks

1 Answer

Hello I have Mazda 2000 MVP when the gas is full the car run fain but if it's below the half level the car can not go faster than 40km.


Have your fuel pressure tested when above half and when it starts to run slow, you may find that you are losing fuel pressure when pump gets hot and at lower level. May be time for new pump, plus filter is part of fuel pump module inside gas tank. Be sure to have it tested though to confirm before replacing if necessary.

Apr 09, 2012 | 2000 Mazda MPV

1 Answer

How do I check the fuel pressure on a 2000 model mazda millenia with a 2.3 engine in it


Hi.

You connect a fuel pressure gauge like this to the pressure rail. Pressure in this car must be between 35 and 45 psi. If pressure is too low look for kinked fuel lines and eventually replace the pump. If the pressure drops down more than 10 psi in five minutes or if the pressure is considerably higher than that replace the fuel pressure regulator. Below the parts that may need testing:

ginko_261.gif

1. Fuel tank
2. Shut-off valve
3. Non-return valve
4. Fuel pump
5. Fuel pump (Transfer)
6. Fuel filter (High-pressure)
7. Injector
8. Pressure regulator
9. PRC solenoid valve
10. Fuel pump relay
11. Fuel pump resistor and relay (KJ model)

Aug 04, 2011 | 2000 Mazda Millenia

2 Answers

Replace fuel filter on 2000 mazda protege


A 2001 Mazda Protege (actually, all models from 1999-2003 including the DX, LX, ES, Mazdaspeed, and Protege 5) does not have an inline fuel filter. The only fuel filter it has is a "strainer" or a "screen", which looks like a nylon mesh "sock". This strainer is connected to the fuel pump, located in the gas tank. Although this fuel strainer does not require periodic replacement, it is recommended that it be changed if you are replacing the fuel pump.

May 03, 2010 | 2000 Mazda Protege

1 Answer

2000 Mazda 626...turn key on...no fuel seems to get to engine...fuel tank is full...could fuel filter restrict and cause problem ?


Check the fuse for the fuel pump. if its bad replace it if it blows again change the fuel pump its on its way out

Apr 26, 2010 | 2000 Mazda 626

3 Answers

Location of fuel pump in 2000 mpv mazda


while you are replacing it, replace the sock at the same time. That is the only "filter" that I am aware of. I had a problem that mimicked a slipping transmission that was because of the sock breaking down. When ever it got low on fuel, the transmission would act up.

Mar 08, 2010 | 2000 Mazda MPV

1 Answer

How to Replace a Fuel pump on a 2000 Mazda 626


yes it isn't that much if you buy them.they slide inside the coupler and release the line.

Dec 26, 2009 | 2000 Mazda 626

1 Answer

Fuel issue


fuel filter is between the tank and engine, usually under the hood. replace the fuel pump.

Sep 27, 2009 | 2000 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...