Question about 2006 Mitsubishi Raider DuroCross

1 Answer

Where is the fuel filter located on a 2006 Mitsubishi Raider Durocross pickup?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Contributor
  • 24 Answers

Its built in with the fuel system in the fuel tank.

Posted on Nov 23, 2014

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: programming instructions for 2006 Mitsubishi raider remote

Note when entering program mode using that fob, all other programmed transmitters will be erased and you will have to reprogram them for your vehicle. Use the following procedure to program additional key fobs if the vehicle is not equipped with Sentry Key:

1. Enter your vehicle and close all doors.
2. Fasten yo belt to cancel any chiming that may confuse you
3. Place the key into the ignition turn to on pos. do not start
4. Press and hold the UNLOCK button on the key fob.
5. After holding the UNLOCK button for four seconds, also press the PANIC button within 6 seconds.
6 When a single chime is heard release both buttons. The chime is an indication that you have successfully entered program mode. All transmitters that are to be programmed must be done so within 60 seconds of when the chime was heard.
7. Using the fob to be programmed, press and hold both the LOCK and UNLOCK buttons, simultaneously for 2 seconds and them release.
8. Press and release the UNLOCK button a single chime will be heard,
9 Repeat steps 7 and 8 to program up to six additional transmitters.
10. Turn the ignition to the OFF position.
11. Your vehicle will remain in program mode up to 60 seconds from when the original chime was heard. After 60 Seconds, all programmed transmitters function normally.

Posted on Sep 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the Transmission control Module on a 2006 Mitsubishi Raider (V8 Durocross)? Is it combined with the ECM as one assembly?


Yes I believe that the pcm controlls both usually it's a sensor issue or wiring issue. We never had many issues with them short of mice damage.

Aug 11, 2016 | 2006 Mitsubishi Raider

1 Answer

Omd code P1775 came on


This is a transmission issue that is related to the transmission not being able to signal a problem.

Feb 13, 2014 | 2006 Mitsubishi Raider DuroCross

1 Answer

Where are the plugs located on my 2006 raider?


Spark plugs? You got the 3.7? Follow the wires-there may be a cover over the entire upper side of the engine.

Mar 12, 2010 | 2006 Mitsubishi Raider

2 Answers

Where is the fuel filter located on the Mitsubishi Raider (2007)?


Inside the fuel pump module inside the fuel tank none serviceable part.

Sep 27, 2009 | 2007 Mitsubishi Raider LS

3 Answers

Windshield wipers dont work in the rain


replace the wiper relay located in the fuse box in the engine compartment.

robert

Sep 10, 2009 | 2006 Mitsubishi Raider

2 Answers

When stop at the red light my 2006 M Raider Stalls.


take it to a mechanic and have the gas flow checked. ask if the pressure is correct. if yes it should be the gas pump. dpnt do anything your self because your not sure of a problem.

Jun 04, 2009 | 2006 Mitsubishi Raider

2 Answers

Question re: ignition system


no , the reason is there anti theft system build in ur car

Mar 17, 2009 | 2006 Mitsubishi Raider

2 Answers

Where is the AIT sensor located on a 2007 Mitsubishi Raider?


The AIT sensor is located inside the large black plastic box on top of the engine. There is a 2-wire plug connector that plugs into the driver side of this box that connects the sensor wires. Mods simply remove the plug and attach the new AIT diode to the plug without plugging it back into the black box. Note: Your check engine light will stay on and not much improvement (if any) to performance. I took mine back out and restored back to stock. Don't waste your money on gadgets for the AIT.

Sep 03, 2008 | 2006 Mitsubishi Raider

3 Answers

MPG


Compare Fuel Estimates for 2006 Mitsubishi Raider Trucks Here's a comparison of EPA fuel economy ratings among the trucks in the 2006 Mitsubishi Raider lineup. As always, your mileage will very likely differ. 2006 Mitsubishi Raider 2WD 6-cylinder Trucks * 3.7L, 6-speed manual, 16 city / 22 highway * 3.7L, 4-speed automatic, 16 city / 22 highway * 3.7L, 6-speed manual, 16 city / 20 highway

May 15, 2008 | 2006 Mitsubishi Raider

Not finding what you are looking for?
2006 Mitsubishi Raider DuroCross Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...