Question about Cars & Trucks

1 Answer

I have a chevy blazer 2003 my dash lights went out and beat cluster not working wat could this be

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,679 Answers

Check the fuse box , lower dash drivers side , owners hand book will list position etc of what fuse or usually printed on the fuse box cover/lid

Posted on Nov 13, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 chevy tahoe, all the gauges went dead. i replaced all the stepper motors and still nothing works any ideas.


Gm has a problem with its clusters. If the guage fuse is ok try slapping on the dash above the cluster to see if anything comes back online. If not I would suspect an internal cluster issue and it will have to come out for repair/replacement

Apr 12, 2015 | 2003 Chevrolet Tahoe

1 Answer

Gauges and radio went out


if you beat on the bottom of the dash where youre knees are it will probably come on common problem, on my 98 i pulled the cluster (not hard) and took a pair of needle nose pliers and just slightly twisted all the pins that go into the back of the cluster to make better contact than put dilectric grease on them
if you google cherokee forums you will find all the answers you need

Feb 02, 2013 | 1999 Jeep Cherokee

1 Answer

I'M WORKING ON A1997 CHEVY BLAZER THE FUEL PUMP WENT OUT AND WAS REPLACED WILL START SOME TIMES REPLACED RELAY DIDN'T FIX IT WHEN IT WILL START THE WORNING LIGHTS ON THE DASH WILL COME ON WHEN


Check the engine bulkhead main wiring connector in front of the driver on the firewall, see if it is loose or corroded, remove it and reinstall it. This can also be due to the ignition starter switch being defective on the rear of the ignition key cylinder, very common on this model..

Oct 02, 2012 | 1997 Chevrolet Blazer

1 Answer

Gas gauge does not work on my 2000 blazer ls 4.3l


Maybe could be ground problem. I would also check fuse/ relay for dash cluster.

Aug 23, 2017 | 2000 Chevrolet Blazer

1 Answer

Dash lights dont work on my 97 blazer


All lights, or just your illumination lights? Illumination: bulbs need replacing. All lights; SERIOUS problem. There is a dash panel fuse on car. check that. Has anyone done any work recently under dash( like installing a radio)? May be they accidentally pulled a connector loose behind dash. Need to pull your instrument cluster to check that. Usually two big connectors with lots of wires going to back of instrument cluster. If no power at all with key on: check under hood at power distribution center for a main big fuse out.

Oct 12, 2011 | 1997 Chevrolet Blazer

1 Answer

I recently bought a 1998 Chevy Blazer 4dr. The dash lights (speedo, gas gauge etc) never worked, and recently the cigarette lighter went out to. Just after the cigarette lighter conked out I found one of...


Hi, that fuse did not come with your car. It may go to your radio, if someone installed an aftermarket radio in the truck.
Your fuses are laid out in the owner's manual, which you can download here if you don't have one:
http://www.extendedgmwarranty.com/owners-manual/chevrolet/1998-Chevrolet-Blazer.pdf

Fuses start on page 6-60. The lighter fuse is #2 in the box at the end of the dash board. The instrument lights are powered by fuse #5, but that would be for all of the lights. If only the 2 gage lights are out, you probably need to replace the bulbs. I have pasted instructions for removing the instrument cluster below. Note that you may be able to replace bulbs without disconnecting everything and removing the cluster. It just depends on how much slack is in the cables, so try pulling the cluster out a bit with wires still attached to see if you can do it. Please let me know if you have more questions, and thanks for using FixYa.

1995-98 Models

  1. Disconnect the negative battery cable.
  2. If your vehicle is equipped with a tilt steering wheel, move the wheel to the lowest position. If the vehicle does not have a tilt wheel, it may be necessary to lower the column.
  3. Unfasten the eight clips that retain the instrument cluster bezel and remove the bezel. There are four clips on the top of the cluster bezel and four clips on the bottom of the cluster bezel.
  4. Unplug the electrical connections from the headlamp switch, dimmer control and any other accessory switches that would interfere cluster removal.
  5. Unfasten the four cluster retaining screws and remove the cluster making sure nothing contacts the circuit connections.
  6. If replacing the bulbs, turn the bulb assembly 1 / 2 turn to the left to remove.

To install:
  1. Install the bulb assembly.
  2. Place the cluster into position without touching the connector pins. Install and tighten the cluster retainers.
  3. Attach the headlamp switch, dimmer control and any other accessory switches.
  4. Install the cluster bezel.
  5. return the steering wheel or column to its original position.
  6. Connect the negative battery cable.

Jan 10, 2011 | 1998 Chevrolet Blazer

1 Answer

Dash board is digital and the dash lights went out seeking information on how to remove the dash board console 1993 chevy blazer tahoe LT


Remove the 5 mounting screws from the instrument cluster trim plate and remove the trim plate. Remove the 4 mounting screws from the instrument panel face plate and remove the face plate.Remove the instrument light grid from the center of the cluster. From behind the instrument cluster reach behind the speedometer and disconnect the speedometer cable by releasing the tab. Pull the cluster forward just enough to detach the "check engine" light bulb from the center of the cluster. Remove the instrument cluster from the dashboard.

Jan 13, 2010 | 1993 Chevrolet S-10 Blazer

1 Answer

How do I get to the check engine light my 2000 chevy blazer


u have to take the bezel off around the front of the dash after that is off just take out your cluster and twist the bulb out

Jul 31, 2009 | 2000 Chevrolet Blazer

1 Answer

Computer problem?


this is defiantly a CPU issue but, at the least, it could be a fuse box issue as well. check both to be safe.. oh, some stereos that are purchased and installed incorrectly can cause this as well.

Jan 28, 2009 | 1997 Chevrolet Blazer

3 Answers

Turn signal relay switch, 94 s10 chevy blazer


The Turn signal relay on a 94 s10 blazer is located under the cluster area right behind the panel that holds the parking brake release handle you will see it once a couple of trim panels get remove it will be to the right side of the brake release handle

Nov 18, 2008 | 1994 Chevrolet S-10 Blazer

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...