Question about Cars & Trucks

1 Answer

What are the tightening torques of the nissan zd30 engine?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,679 Answers

Follow this link for the HEAD torque settings and click on torque tables
http://www.speedwayautoparts.com/index35.htm

Posted on Nov 13, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 8 Answers

SOURCE: engine head torque settings for 2005 nissan sentra 1.8

email me ill send you it via email cant post here too bigg!!

Posted on May 29, 2009

tneubauer
  • 437 Answers

SOURCE: torque and tightening sequence for 1999 2.2 chev

Cylinder Head Bolts

Step 1
Head Bolts A 46 (62)
Head Bolts B 43 (58)

Step 2 Additional 90 Degrees

Tightening Sequence:
http://www.anubiscycle.com/fixya/99cavheadsquence.png

Posted on Jan 17, 2010

chris bean
  • 61 Answers

SOURCE: nissan navara 2006 blown hole no1 piston 16000kms

do you have a hole in the piston or gasket? If in the piston it is most likely from coolant or water. If water, could be a cracked head, or being sucked in through the intake and building up in the 6th cyl. I have a lexus that had a hole in the side of the motor and noon could figure out why. I pulled the head and found water... Put new block in and egr codes came up. Pulled EGR and found it was sucking in water, due to an exhaust leak that was allowing condensation to build and would not blow out once in the egr tube. If you face the same problem (hole in block) I am going to say too much compression. Could be from head gasket not being torqued properly and leaking cooland, cracked head, or wrong spark plugs-and worst case scenario which I have yet to witness, bad spark plug gap. Not likely on your car, i would think.

Posted on Mar 29, 2010

zaldyboy01
  • 293 Answers

SOURCE: i hav nissan patrol 2001 model zd30 engine,why d

that may cause the out of the timing or check spark plug cable came off or needs to tune up.

Posted on Sep 22, 2011

emissionwiz
  • 75117 Answers

SOURCE: final torque settings for nissan navara d22 diesel engine cylinder head

You do not need to re-torque modern cylinder heads. That went out withe Buffalo.

Posted on Nov 07, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have changed cylinder head gasket and need the torque settings for the zd30 nissan engine


try this head torgue link.. that wont highlight

http://www.cylinderheadsaustralia.com.au/torque-settings

the ZD30 is listed half way down the list
and picture of tension sequence

HEAD BOLT TIGHTENING SEQUENCE.
• STEP ONE: 102Nm
• STEP TWO: Loosen All Bolts.
• STEP THREE: 44Nm
• STEP FOUR: +90*
• STEP FIVE: +90*
• IMPORTANT: ALL BOLT THREADS, BOLTHEADS AND WASHERS MUST BE LIGHTLY OILED.
• USING AN OLD HEADBOLT WITH GROOVE CUT DOWN THREAD, CLEAN THE BLOCK HEADBOLT THREADS.




why are these torque setting and sequence
numbers no longer on the VRS head gasket packaging

Oct 28, 2016 | Nissan Cars & Trucks

1 Answer

Where can i find a pump injector spare part of isuzu zd30 small in nairobi


no year state
zd30 is that not Nissan?
what car, is a zd30
wow country, stated, like 3rd time in 1,000,000 post,
you are savvy poster...
this is usa forum and our stores down sell zd30 parts
you need to shop in Nairobi. (or near)
my guess, is go to any Nissan dealer?
Diesel engine.
my guess is your car is.... right (its a wiki page)

  • Patrol - Chassis Code Y61
  • Caravan - Chassis Code E25 and VWE25
  • Urvan - Chassis Code E25
  • Homy - Chassis Code E25
  • Elgrand - Chassis Code E50, E51
  • Terrano - Chassis Code R50
  • Terrano - Chassis Code R20 (Europe only)
  • Atleon

Feb 24, 2016 | Isuzu Cars & Trucks

1 Answer

Nissan navara 2002 twin cab diesel zd30 malfunction light comes on randomly


NISSAN NAVARA questions and answers

www.roadtestreports.co.uk/vans/nissan/navara/qanda/
Results 1 - 40 of 322 - Ask and answer questions on a variety of NISSAN NAVARAmodels. Help and advice ... Have a Navarra Rally Raid 2004 double cab pick up. ... Navara V6 2011 - loss of power & engine management light on. .... ZD30 I have changed the diesel filters after noticing that it's jerking when I'm on full throttle.

Nissan Patrol GR Y61 ZD30 starting problem - YouTube

? 1:23
https://www.youtube.com/watch?v=JxHKfYDCgFQ
Jan 16, 2013 - Uploaded by sspyropoul
After replacing the diesel filter seals and water trap i had no problem .But you ... They still glow for like 15 ...Missing: twin ‎cab ‎randomly

Nissan D22 Navara receives YD25 2.5-litre diesel

www.themotorreport.com.au/.../nissan-re-power-their-d22-navara-range
Jan 31, 2008 - Nissan's popular Navara D22 workhorse range has been ... On top of the 4x4 DX single cab's equipment, the dual cab ST-R adds .... the yd25 engine have a overheating problem, so how comes nissan is ... I believe it is a ZD30 engine. .... with no problems except a cracked injector line (pretty random fault).

Jan 13, 2016 | Nissan Cars & Trucks

1 Answer

2010 Y61 ZD30 Patrol code P0090,P0088?


Check your wire diagram it could be IGN bad wire

Jun 23, 2014 | 2004 Nissan Nissan almera tino

1 Answer

Cylinder head torque settings for a Nissan KA24E engine


54 - 61 foot pounds of torque. Be sure to follow the tightening sequence!

Dec 25, 2013 | Nissan Cars & Trucks

1 Answer

Final torque settings for nissan navara d22 diesel engine cylinder head


You do not need to re-torque modern cylinder heads. That went out withe Buffalo.

Nov 07, 2012 | Nissan Cars & Trucks

1 Answer

Hi i'm eduardo and i have a '94 nissan pathfinder 4wd...engine 3.0.... i want to know the head torque specifications .


Hi Eduardo:
Check this information (click over pics for zoom)...

zjlimited_1062.jpg

Fig. 20: Exploded view of the cylinder head assembly-VG30E engine


zjlimited_1063.jpg

Fig. 15: Cylinder head loosening sequence-VG30i and VG30E engines


zjlimited_1064.jpg

Fig. 17: Cylinder head torque sequence-VG30i and VG30E engines


Install the cylinder head with a new gasket. Apply clean engine oil to the bolt threads and seats, then install the bolts with washers (beveled edges up) in the correct position. Note that bolts 4, 5, 12 and 13 measure 5.00 in. (127mm), and are longer than the others. The other bolts are 4.17 in. (106mm) long.

Tighten the bolts in the proper sequence, in the following stages:
Tighten all bolts, in order, to 22 ft. lbs. (29 Nm).
Tighten all bolts, in order, to 43 ft. lbs. (59 Nm).
Loosen all bolts completely.
Tighten all bolts, in order, to 22 ft. lbs. (29 Nm).
Tighten all bolts, in order, to 40-47 ft. lbs. (54-64 Nm). Or, if you have an angle torque wrench available, tighten them an additional 60-65 degrees.


Hope this helps; remember to rate this answer. Good luck.

Apr 22, 2011 | Nissan Pathfinder Cars & Trucks

1 Answer

What is the cylinder head torque spec for a 2005 nissan sentra 1.8 liter engine


  1. For 1.8L engines, tighten the bolts in sequence, as follows:
    1. Step 1: Bolts 1-10 to 22 ft. lbs. (29 Nm).
    2. Step 2: Bolts 1-10 to 43 ft. lbs. (59 Nm).
    3. Step 3: Loosen bolts 1-10 completely.
    4. Step 4: Bolts 1-10 to 22 ft. lbs. (29 Nm).
    5. Step 5: Bolts 1-10 plus 50-55 degrees.
    6. Step 5: Bolts 11-14 to 74 inch lbs. (8 Nm).

      0900c152801afb79.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Cylinder head torque sequence-1.8L engine


      0900c152801afad8.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Tighten the valve cover bolts in sequence-1.6L and 1.8L engines

Nov 13, 2009 | 2005 Nissan Sentra

1 Answer

Need 1990 nissan sentra torque settings and valve clearence


heinrichkemp: The engine in your car is a GA16i
I venture you are asking about the head bolts when you refer to torque settings. The head bolts used on this motor are torque to yield (streach bolts) If you are reusing them, you need to check them to insure they are not stretched beyond limits.
The way you measure the bolt is with a micrometer.
Measuring close to the end where the bolt starts to thread in, about 10-12 threads up, take a reading. Now, go to the other end of the bolt where the threads end and measure about 10 threads in.
There should not be more than a .009 inch difference (.228mm). If there is, discard the bold and get a new one.

You must use a sequence to tighten the bolts, below is the sequence.
11
13 9 3 1 6 8

14 7 5 2 4 10
12 15

torque 11,12,13,14 & 15 to 8.3 Nm (6.1 ft lbs)
Torque the main head bolts by the numbered sequence to
29Nm (22 ft lbs) first pull
64Nm (47 ft lbs) second pull
Loosten all the bolts completely
Tighten the to 29Nm (22 ft lbs) first pull
Tighten bolt # 1 clockwise 85 degrees
Tighten bolts #2- 10 65 degrees
Nissan noted that if you do not have a torque angel meter, you can use a regular torque wrench and torque all the bolts to 69Nm (51 ft lbs)
The valves on this engine have hydraulic lifters, consequently require no adjustment.

Apr 11, 2009 | 1990 Nissan Sentra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

229 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...