Question about Cars & Trucks

Open Question

How to reset turbo timer after disconnecting battery

After i replace the battery the alarm is working but the turbo timer is not so what can i do to resert it

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
mythman
  • 84 Answers

SOURCE: new battery -alarm sounds- have to disconnect the battery-

The sounding alarm maybe a security system installed by in the truck. Disconnecting the battery will only temporarily solve your problem, but will resume once you reconnect the battery for electrical power.

You must find the keychain/remote of the security system and disable it. If you are unable to locate this, you can have it disconnected by a qualified automotive electrician.

Word of caution though, if you are using the keyless entry system with the security system, this will be disabled until you install a receiver with such function.

Hope this helps.

Posted on Jun 30, 2009

Ad
  • 15 Answers

SOURCE: ELANTRA ALARM PROBLEM

If the alarm keeps going off constantly and the remote has no influence on the alarm its most likely a connection problem. A hyundai dealer might be able to fix it but since you can start the car something you might be able to try is....
Check and make sure the remote battery is in the right way. Make sure all of the doors are closed, the trunk is closed, open the hood, connect the battery, close the hood all the way and try to lock and unlock the doors. Hope this works but if not, sorry it didn't work.

Posted on Jul 08, 2009

saailer
  • 1868 Answers

SOURCE: I have a factory installed alarm on my 2003 jeep cherokee ,how do i disable alarm

Hello! The drivers side door lock/unlock switch is more than likely defective...Having said that, the alarm system on Jeeps are a constant problem...To disable the system requires removing the drivers door panel and cutting the Light Green/Orange wire at the switch...And installing a 465 Ohm resistor...Not something done without the necessary skills...
I would have the vehicle towed to a Jeep dealer and have them test the drivers door switch and disable the alarm....Guru...saailer

Posted on Feb 02, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I replaced the battery in my 2008 Chevrolet Colorado and the factory alarm aka my horn won't stop going off. How do I reset my alarm?


pull the horn relay till its sorted
factory alarm may need a diagnostic scanner
might be a faulty module

Apr 16, 2017 | Chevrolet Cars & Trucks

1 Answer

Car alarm preventing car from starting


Try removing the alarm system relay, some car alarm has also a fuse on the alarm that you can remove.
Many car alarms unlock by inserting and turning car key while you connect the battery.

Aug 19, 2008 | 1998 Chrysler Sebring

1 Answer

My turbo timer is not not working after i disconnected my battery and connect it back


It may need resetting for the time that you want it to work for as the setting may be lost from disconnecting the power supply.

Nov 12, 2014 | Cars & Trucks

2 Answers

2005 Volvo S40 Immobilizer


you need a scanner having your car's program and to do the alarm reset to reset the alarm.

Aug 28, 2012 | 2005 Volvo S40

1 Answer

I can't turn off the security alarm on my 1998 nissan pathfinder


I couldn't turn off the security alarm on my 1999 Pathfinder as I replaced the battery,
Solution: I read the solution here to disconnect the positive cable, open the driver's door, insert the key, then reconnected the positive cable, while honking, I turn the key to the left, to the right and to the left again while the door is still open. The honking stopped. Then I started the truck without a problem. Thank you for the hint.

Jun 12, 2012 | 1998 Nissan Pathfinder

1 Answer

I have a factory installed alarm on my 2003 jeep cherokee ,how do i disable alarm


Hello! The drivers side door lock/unlock switch is more than likely defective...Having said that, the alarm system on Jeeps are a constant problem...To disable the system requires removing the drivers door panel and cutting the Light Green/Orange wire at the switch...And installing a 465 Ohm resistor...Not something done without the necessary skills...
I would have the vehicle towed to a Jeep dealer and have them test the drivers door switch and disable the alarm....Guru...saailer

Feb 02, 2012 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Could a low battery cause car alarm to activate .....I have a Audi a4 1800 turbo Cabriolet ?


the alarm system for audi/vw/seat/skoda is based on power drop,so yes is the answer and you need to reset alarm system/remotes if you replace battery or disconnect it for any reason not forgeting the radio code...

Apr 30, 2010 | 2004 Audi A4

1 Answer

My alarm 'clicker' stopped working - now I have a


Replace clicker batteries leave them out and hit reset internal dot inside clicker !

Jul 28, 2009 | 1995 Pontiac Bonneville

1 Answer

ELANTRA ALARM PROBLEM


If the alarm keeps going off constantly and the remote has no influence on the alarm its most likely a connection problem. A hyundai dealer might be able to fix it but since you can start the car something you might be able to try is....
Check and make sure the remote battery is in the right way. Make sure all of the doors are closed, the trunk is closed, open the hood, connect the battery, close the hood all the way and try to lock and unlock the doors. Hope this works but if not, sorry it didn't work.

Jul 04, 2009 | 2001 Hyundai XG300

1 Answer

Alarm wont shut off after replacing battery


How long did it take you to replace the battery? If you did a quick switch, try disconnecting it again and leave for 10-15 minutes. Maybe it will reset? Did you replace the battery before it went completely bad? Is this a stock alarm?

Dec 14, 2008 | 2003 Hyundai Tiburon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...