Question about 1964 Holden EH

1 Answer

I need a throttle linkage diagram for an EH Holden

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Holden Master
  • 51,307 Answers

Contact me with you e-mail address in the comment box and I will send you a copy of the throttle set up

Posted on Nov 13, 2014

  • roy robinson
    roy robinson Nov 13, 2014

    Thanks Bill, Address is



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Diagram of the linkage on the throttle body of 88 honda accord dx

Type this into YOU TUBE. It shows the linkage.
Hope this helps.
Honda Civic DX Throttle Cable Tightening.

Apr 25, 2018 | Honda Cars & Trucks

1 Answer

Holden barin auto not changing down

Check the throttle linkage and cable to ensure that full throttle is reached by the throttle vale and throttle position sensor if that is OK check the detent switch to ensure that it operate4s on full throttle

Feb 16, 2016 | Holden Cars & Trucks

1 Answer

Ss commdore mamaul 1994

Check to see if the kickdown cable from the throttle linkage to trans is working.
Next step is to get someone with auto experience to drive it and give a more accurate diagnosis.

Jul 01, 2014 | Holden Commodore Cars & Trucks

1 Answer

Holden manuals

Check the linkage and neutral safety switch for moisture..

Linkage must able to move the neutral safety to switch gear.

Jan 15, 2014 | Holden Cars & Trucks

1 Answer

Twin hs2 su carb linkage diagram

YOU dont need a diagram for twin carbys as put them on the manifold back off all throttle linkage and adjustment screws make sure thay are all down, and turn both screws down till they touch, now back off the jets nuts under the carbys and then undo them 2 turns only[thats the ones the choke move up and down] now HB on out of gear a little choke start engine adjust 2 screws 1 more turn each and choke in
make sure you have very thin oil in pistons, then when running adjust jets 1flat at a time when it runs smooth lock up the linkage and adjust screws till idle at 600 RPM.

Aug 15, 2012 | Austin-Healey SPRITE Cars & Trucks

1 Answer

Holden barina 1994 manual gearbox linkage problem

had the same sorta problem with my one, i replaced the las part of the linkages thats connecte to the gearbox, that helped with it. also check to see if the blots holding ur gear stick in place are tight

Sep 01, 2009 | 1994 Honda Civic

1 Answer

Missing factory throttle linkages on 1990 YJ jeep. Need Diagram

Go to any scrapyard and you can get the entire setup for next to nothing...and you can see how it's hooked up!!!

Jul 07, 2009 | 1990 Jeep Wrangler

1 Answer

Transmission gets jerky like it can't decide whether to shift or not When shifting down manually the jerky diminishes

Try spraying all the linkages & or cable at throttle linkage & at side of transmission with WD-40 or similar, to get things loosened up, then give a coat of white lithium grease or similar spray to keep it lubed up.
Engine off, wheels blocked etc.when you go under eh? safety first.
That may be all you need, if not get back to us.

Apr 26, 2009 | 1987 Chevrolet Caprice

1 Answer

Gas pedal linkage

Don't need a diagram.
Start by checking to see that ur cable hasn't come off the throttle body or that the clip in the floor behind the gas pedal is still there.
If it's broken, remove the clip on the floor and remove from the throttle body. Disconnect the cable from the pedal and pull it out from the inside of the car.

Aug 22, 2008 | 1994 Volkswagen Jetta

Not finding what you are looking for?
1964 Holden EH Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Holden Experts


Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14417 Answers

Are you a Holden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides