Question about 2003 Toyota Highlander

1 Answer

<!-- from fixya rte -->Why is my speedometer not reeding - 2003 Toyota Highlander

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Toyota Master
  • 2,494 Answers

Check speedo drive gears in extension , if cable driven check inner cable.

Posted on Nov 13, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My car dies while I am Driving


Hello
The engine and automatic transmission in this vehicles drive train are fully electronically controlled by a computer called the PCM (Power Train Control Module). Whenever a problem like this occurs the computer stores a record of the problem (there are of course some exceptions to this, like the fuel pump, engine coolant temperature sensor and MAF sensor for instance) in the form of a fault code in its memory, to read these fault codes you must have the systems memory scanned with a special tool. Once the fault code(s) are read you then must perform the appropriate diagnostic testing to find and resolve the problem(s) DO NOT REPLACE ANY PARTS UNTIL A TRAINED TECHNICAIN HAS DIAGNOSED THE PROBLEM TO AVOID SPENDING YOUR HARD EARNED MONEY ON PARTS THAT MAY NOT CORRECT THE PROBLEM

Aug 24, 2012 | 1999 Chevrolet Malibu

1 Answer

Where can i find the speeddometer reed switch on the engine/


I believe its built into the speedometer if you are talking about the speed sensor..

Feb 24, 2012 | 2002 Hyundai Accent

1 Answer

Subaru 97 speed sensor trouble code p0500 not passing admissions.. what part to I buy and where is the sensor located?


There are actually two Vehicle Speed Sensors (VSS). I'm going to assume you have a 2.5 liter engine and an automatic transmission.

The Vehicle Speed Sensor 1 (output shaft rotation sensor) is mounted to the extension case (from the outside of the case). The sensor outputs a pulse signal which is transmitted to the TCM where it is converted to vehicle speed.


The transfer clutch drum is connected directly to the rear wheel driving propeller shaft. Vehicle speed sensor 1 on the AWD model detects rear-wheel speed.

zjlimited_382.gif

Vehicle Speed Sensor 2 provides vehicle road speed information to the ECM. The ECM uses this data to properly determine ignition and fuel delivery curves. The sensor consists of a reed switch and magnetic rotor turned by the speedometer cable.


One rotation of the magnetic rotor opens and closes the reed switch four times, producing a digital signal which is converted to vehicle speed by the ECM. The sensor operates whenever the vehicle is moving with ignition ON. As the transmission rotates, the speed sensor sends a pulsed on/off signal to the ECM.


zjlimited_383.gif

The speedometer uses VSS 2 for it's signal.

Hope this helps (remember to rate this answer).

May 24, 2011 | 1997 Subaru Outback

1 Answer

My speedometor does not reed the proper speed it will reed 100 when you are not moving


The stepper motors on the dash board instrument panel are bad. There was faulty motors and you can buy them on ebay. In order to replace them you have to take the instument panel out, (go to youtube for the video) then you need to unsolder the old motors and solder the new ones in. I had never done something like this and took about an hour to replace two motors one on the gas guage and the other on the speedometer. They take the same stepper motor.

Mar 19, 2011 | 2004 GMC Sierra

1 Answer

Replaced starter 1996 5.7 V8 now it misfires at 50 mph


reed valves are usually in 2 stroke engines, they are a valve that controls air fuel intake on carburetors..
why asking?

Jul 31, 2009 | 1996 Chevrolet Suburban

1 Answer

I have LB light on the tablo , and the accalerator hangs


You have to remove the speedometer and locate and remove in the back a screw which says REED, then put everything in place. Whithout that screw the L/B Lean burn light dont turn on again.

Jul 19, 2009 | 2002 Hyundai Accent

2 Answers

Coolant sensor location


it should be located on the bottom of the rad

Dec 10, 2008 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
2003 Toyota Highlander Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...