Question about Cars & Trucks

1 Answer

How do i get my window up until i get a switch

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

If the motor is stripped you may be able to have someone run the switch while you pull the window up with the door open. Do so by standing with a hand on the outside and apply same pressure with other hand on the inside and push up while the other helper mans the switch. If motor is dead then you're screwed!

Posted on Nov 12, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset windows on is 350 lexus 2007


(a) Turn the engine switch on (IG).

(b) Halfway open the power window by pressing the power window switch.

(c) Fully pull up the switch until the power window is fully closed and continue to hold the switch for approx. 1 second after the power window is fully closed.

(d) Check that the AUTO UP/DOWN function operates normally.

If the AUTO UP/DOWN function operates normally, reset operations have been completed at this time. If not normal, follow the steps below.

(1) Disconnect the negative battery terminal for 10 seconds.

(2) Connect the battery terminal.

(3) Turn the engine switch on (IG).

(4) Halfway open the power window by pressing the power window switch.

(5) If the AUTO UP/DOWN function operates normally, reset operations have been completed at this time.

If not normal, follow the steps below.

(6) Turn the engine switch on (IG).

(7) Halfway open the power window by pressing the power window switch.

(8) Fully pull up the switch until the power window is fully closed and continue to hold the switch for approx. 12 seconds after the power window is fully closed.

(9) Check that the AUTO UP/DOWN function operates normally.

Feb 05, 2017 | 2007 Lexus IS 350

1 Answer

Why does the power window button blink on and off and the automatic feature doesn't work in the 2008 Toyota Sienna?


NOTE:
Anytime the batteryterminal has been disconnected, please initialize the driver's door power windowand front passenger's door power windowafter reconnecting the batteryterminal.

With ignition switchin the "ON" position, do the following:

1. Push down and hold the driver's door power windowswitch to completely open the window.
2. Pull and hold up the driver's door power windowswitch until the window closes.

Continue holding the switch for approximately one second until the switch changes from blinking to a constant illumination.
3. Check for proper operation of the "one-touch open and close" function by fully pushing the switch briefly to the "DOWN" and "UP" positions.

At this time the power window switchfor the passenger's door windowshould be blinking.
4. Push down and hold the passenger's door power windowswitch to completely open the window.
5. Pull and hold up the passenger's door power windowswitch until the window closes.
Continue holding the switch for approximately one second until the switch changes
from blinking to a constant illumination.
6. Check for proper operation of the "one-touch open and close" function by fully pushing the switch briefly to the "DOWN" and "UP" positions.

Feb 09, 2016 | Toyota Cars & Trucks

2 Answers

Replaced battery, now auto windows wont come up auto automatically


If on a GM car the battery has been disconnect the windows may need to be reprogrammed
The following steps explain how to program the side door window regulator motors:


  1. Press and hold the power window switch until the window is fully DOWN. Continue holding the power window switch for approximately 3 seconds.

  2. Press and hold the power window switch until the window is fully UP. Continue holding the power window switch for approximately 3 seconds.

  3. The power window regulator motor is now programmed for the express function.

  4. Repeat this process for all of the power windows.

Dec 01, 2015 | Cars & Trucks

1 Answer

Fix for the door glass,2009 CHALLENGER. Won't reset to down position when opening door to allow window to break seal.Then move up and seal glass when door is closed. SMart Glass?


This may be as simple as relearning the window stop positions. Perform the following procedure to relearn the windows;

1) Sit in the drivers seat and ensure both doors are fully closed.
2) Turn the key to the ON position but do not start the vehicle.
3) Pull up on the drivers window switch until the window reaches the full up position, then CONTINUE HOLDING THE SWITCH UP for 2-5 seconds, then release the switch.
4) Push down on the drivers window switch until the window fully opens, then CONTINUE HOLDING THE SWITCH DOWN for 2-5 seconds, then release the switch.
5) Repeat steps 1-4 for the passenger window.
6) Close both windows and check the operation of the smart glass.

Let me know if you need further help.

Nate

Oct 18, 2014 | 2009 Dodge Challenger

1 Answer

How to reset my master power window switch on jetta 2010


switch ignition on, engine off. fully open window fully close window, lift and hold window close switch until window motor emits a clicking sound, repeat procedure for remaining windows,switch ignition off. sound like battery been replaced disconnected, if this procedure dont work let dealership check it out.could have blowed window switch fuse to that door.

Sep 26, 2012 | 2010 Volkswagen Jetta 1.6

2 Answers

The window switch on the drivers door to raise and lower the rear passenger is not working. I was able to lower the window but now it is stuck in the down position. Is there a way to override and roll up...



  • So if I understand you correct the drivers door switch is not working for the rear window.
  • Try using the the switch on the rear door for that window then.
  • The master switch is great to work all windows but the rear window switch should still work as well even if the master switch on the drivers door fails.
  • Now if both switches should don't work then it may not be a switch failure at all. this could be a wiring issue or a burnt window motor/regulator.
  • In this case you will nee some help as you are going to "help" the regulator out. Once you get it up I advise to let it be until repaired. You don't want to stress the track up to much before the whole assembly is replaced (should this be the problem).
  • So if both switches don't respond the your going to grab the window (one hand on each side of the window) as if your palms are touching and pull up at the same time the switched is being pushed up.
  • It may take a bit to get it but it will be fine.
  • If the window is down in the door (in the way down position) then get your fingers in there and grab the window and slowly pull up on it. Make sure the switch is being pushed to roll the window up at the same time.
  • Once you get it up a bit then take it the rest of the way as explained above.
  • I have had to do this on a few occasions and it works fine.

  • Hope this helps and thank you for using FixYa.

Regards, Tony

Jul 13, 2011 | 2005 Scion xB

1 Answer

Where is the rear window relay located on the 2002 Ford Explorer sport trac. Not the rear door windows but the very back window.


  • The power rear window is inoperative (Explorer Sport Trac only)
  • Circuitry.
  • Battery Junction Box (BJB) fuse 3 (30A).
  • Central Junction Box (CJB) fuse 20 (7.5A).
  • Power rear window control switch.
  • Rear window glass motor.

NOTE: The power rear window motor is not on the multiplex link. Any diagnosis and testing carried out on the power rear window will not involve the GEM module. NOTE: The reinitialization procedure must be carried out when repairs are performed on any part of the power rear window system including when the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.

Rear Window Motor Initialization s1r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure that no obstructions are present in the power rear window system when carrying out this procedure.
NOTE: This procedure must be carried out when repairs are performed on any part of the power rear window system including when: the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.
NOTE: All power rear window components (window glass module, window regulator, window motor, and glass runs) must be installed and torqued to specification before carrying out this procedure.
NOTE: Steps 1-6 must be completed within 30 seconds. The entire procedure must be completed within five minutes.
NOTE: Once the ignition key is turned to the ON position in Step 6, it must remain on until the entire procedure is completed.
NOTE: Steps 7 and 9 require that the power rear window control switch be held in the closed position until the power rear window motor stalls the window in the upper header seal. Step 8 requires that the window control switch be momentarily turned to the open position.
  1. Start with the ignition in the OFF position.
  1. Turn the ignition to the ON position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the OFF position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the ON position. The power rear window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has entered initialized mode.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls in the upper header seal.
  1. Momentarily rotate the power rear window control switch to the open position and release. The power rear window will carry out a one-touch down operation until the window stalls at the bottom of the travel stop designed into the window regulator.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls into the upper header seal. Once this operation is complete, the window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has been successfully initialized.
  1. Verify correct operation of the power rear window by moving the window to the fully open, vent, then fully closed positions
---------------------------------------------------------------------------------------------

Nov 16, 2010 | 2001 Ford Explorer Sport Trac

1 Answer

2006 Grand Cherokee Laredo. Driver side window raises to top then lowers to halfway when you use the button in automatic mode. When using the button at halfway it works normally.


try pressing and holding window switch until window motor stops in down position,then pull up and hold switch until window motor stops..this should recalibrate window position..i hope this helps

Sep 15, 2009 | 2006 Jeep Grand Cherokee

1 Answer

I recently bought a 2002 Pontiac Sunfire SE for my grand daughter as a High School graduation gift. Now the power windows won't go up or down. What could cause this problem? Hoping it is something simple...


This is One with the Power Window SWITCH in the CENTER Console they Often Get Liquids SPILLED on them Causing them to Fail, I Would First Check for 12volts @ the Switch with KEY ON. With a Sure 12volts Going IN the Switch Check for 12 Volt going OUT, If Switch IS BAD there Will be NO 12volts Coming OUT With this Go on to Switch Replacement


REMOVAL PROCEDURE
  1. Use a flat-bladed tool in order to remove the power window switch bezel (1) from the console.
  2. Remove the electrical connection from the power window switch (2).
  3. With a flat-bladed tool release the power window switch (2) tabs, and remove the switch from the power window bezel (1) retainers.
INSTALLATION PROCEDURE \

  1. Install the power window switch (2) into the power window switch bezel (1) until fully seated.
  2. Connect the electrical connector to the power window switch (2).
  3. Install the power window switch bezel (1) to the floor console.
((((>>>All of this is Assuming that All FUSES Related to And RELAYS Related to Windows Have Been Deemed GOOD & Funktional<<<<)))
If Further HELP / SUPPORT / INSTRUCTIONS Are needed P L E A S E Dont RULE me Out as I have the Answers, Just Try to be as Spisific as Possible and I will be More than HAPPY to Help you With your Needs of Auto Repair
  1. Install the power window switch (2) into the power window switch bezel (1) until fully seated.
  2. Connect the electrical connector to the power window switch (2).
  3. Install the power window switch bezel (1) to the floor console.

Jun 15, 2009 | 2002 Pontiac Sunfire

2 Answers

2002 Jahuar xk8 -convertible- Driver's window does not retract back to close position after door closes


If you disconnect the battery you must reprogram both windows by holding the button down until you hear it chime takes about 5 or so seconds. Repeat for the other window and this should solve the problem. This information should be in your owners manual, it is in mine

Jul 20, 2008 | 1999 Jaguar XK8

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...