Question about 1998 Ford Explorer

Open Question

ON THE 1998 FORD EXPLORE IF THE PLUG IS NOT ALL

ON THE 1998 FORD EXPLORE IF THE PLUG IS NOT ALL THE WAY IN THE CLUSTER YOUR GAUGES WILL NOT WORK SO ANYBODY WHO HAS THAT PROBLEM CHECK YOUR GAUGES AND YOU WILL SEE GOOD LUCK TO ALL

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
3dmaster
  • 183 Answers

SOURCE: 1998 Ford explorer transmission 4.0 L OHV Engine

Yes 1 more thing is here for you that can be don by you for activating you car on road,

1.check you battery have a suficiant voltages,
2.check your spark ignition kit,

THNX

Posted on May 17, 2008

Ad
  • 141 Answers

SOURCE: 91 explorer heater not blowing air

The blower motor is located under the hood on the passengers side next to the hood hinge on the firewall. But, check your blower motor resistor first. The resistor is usually the trouble maker. It is located next to the blower motor. It should have 2 screws holding it onto the heater housing. Also an electrical connector. I sincerely hope that this will get it working again. Best wishes to ya.
Bryon

Posted on Jan 26, 2009

  • 202 Answers

SOURCE: 96 ford explorer code p0301 mis fire 1

Sounds like either a bad plug wire, or coil pack. This is about all that would cause the misfire.

Posted on Apr 17, 2009

rteemon
  • 578 Answers

SOURCE: INSTRUMENT PANEL GAUGES DON'T WORK

check your vehicle instrument module

Posted on Jul 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 ford explorer fuel gauge fuse


If your fuel gauge isn't working , it's not a fuse ! The gauge or the sending unit in the fuel tank is bad . If you had other thing's not working in the instrument cluster I would say probably a fuse. There is not a fuse just for the fuel gauge . Fuel Gauge Tech How To Properly Diagnose Faulty Fuel Pump Sending Unit

Jan 04, 2016 | Ford Cars & Trucks

1 Answer

Where is instrament cluster, 2003 explorer?


look right in front of you the cluster has your speedometer gas gauge etc,,,

Apr 24, 2015 | 2003 Ford Explorer

1 Answer

Gauge bulbs replacement


I doubt they would all blow at the same time, check your light switch, fuses. If you wish to replace your bulbs your must remove your cluster from the dash, the bulbs are removed out the rear of the circuit board in rear of speedo, tach, gauges etc.

Dec 13, 2013 | 1998 Ford Explorer

1 Answer

1998 ford explorer fuel gauge stuck on empty-Not the typical suspects causing it?!?!?!


One of the wires to the sensor is touching a ground. It may be getting pinched

Mar 04, 2017 | 1998 Ford Explorer

1 Answer

Speedometer stops working once in a while


check for a loose wire at the back of the cluster, it will look like it is still in the connector but it is not all the way in, I forgot witch pin it is but it is in the middle row or bottom and about the 5-8th pin from the left, Hope this helps

Mar 05, 2010 | 1998 Ford Explorer

1 Answer

Gauges not working


OK, check the fuse box to see if the fuses that are designated for these instruments are still in working order. if the fuses are ok, remove the instrument cluster from the dash and, check the back side of the cluster board. pull all connecting plugs to check the metal contacts on the cluster board. try to straighten the plugs and re attached the wiring harness, this should revive the gauges.

if this dose ot produce results, replace th entire cluster.

Jun 21, 2009 | 1995 Ford Ranger Supercab

1 Answer

Odometer is not working


SOUNDS LIKE THE GAUGE CLUSTER IS BAD OR HAS A BAD GROUND

May 11, 2009 | 1996 Ford Explorer

1 Answer

Dashboad Temperature and Fuel gauge is not working


pull the console out and check connections if the connections are good you may need to replace the instrument cluster.

Apr 20, 2009 | 1998 Ford Taurus

Not finding what you are looking for?
1998 Ford Explorer Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

78257 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5653 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...