Question about 2007 Renault Scenic 2.0

Open Question

What is the torque settings for Renault scenic

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

raffaiel
  • 209 Answers

SOURCE: torque setting for front driveshaft nut

ddc64a1.jpg

Posted on Apr 15, 2009

  • 4044 Answers

SOURCE: renault scenic drivers electric window motor runs

The track guide that operates the window from the motor is damaged or has jumped track. Remove the inner door panel and operate the window and see which has happened. If it has jumped track check for missing or damaged guide retainers if it is damaged or broken replace it. Normally runs about $15 to $20 for the part. Now if the drive guide is not damaged and it is still not working the gear that drives it is damaged and you will need to replace the motor as this is pressed on and not user replaceable. Good Luck

Posted on Sep 12, 2009

  • 1986 Answers

SOURCE: inner door panel removal, renault megane scenic

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Posted on Sep 23, 2009

  • 2 Answers

SOURCE: My Renault Megane Scenic S reg heater is not working

Most likely to be a faulty resistor block, which has 3 resistors and a thermal fuse controlling fan speeds 1,2 and 3, maximum speed 4 by-passes the resister block. It may also be poor electrical connections to the resistor block caused by overheating. Renault ask for approximately £350 to carry out repairs, a replacement resistor block will cost £50. If you decide to carry out the repairs yourself, be advised that if you are not competent to carry out such work you, could cause electrical damage or worse an electrical fire.

Posted on Nov 14, 2009

  • 1 Answer

SOURCE: torque settings for renault megane engine

Does anyone know the torque settings for the following Cam box(bolts), head bolts & crank shaft, the megane scenic is 2001.

Posted on Feb 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My renault scenic 1.9 diesel its stating but not moving


engine starts but no forward or reverse gears

a manual gearbox
gear selection linkage /clutch / drive line failure

auto faults
low on oil
failed torque converter
gear selection linkage
drive line failure

26338852-vgifjk0cmh4fityltrfmb02q-5-1.jpg

Nov 03, 2016 | Renault Cars & Trucks

1 Answer

Torque setting for wheel nuts on Renault Alloy wheels


130(NM) 96 ft/lbs is the torque setting for a 2008 renault scenic so as not to ruin studs or brake rotors should be sufficient for allloys just need to check alloy lug nuts more often

Aug 09, 2014 | Renault SCENIC Cars & Trucks

2 Answers

What is the torque setting for my alloy wheels?


Your torque spec is usually based off of lug diameter, if you have 19mm lug nuts then 75#ft should be sufficient.

Aug 09, 2014 | 2007 Renault Scenic 1.5

1 Answer

I had a fan belt and pulley replaced on a renault megane scenic now the car wont start any help pls


they probly screwd up the timing-the shaft moved when torqueing--the mechanics nevr testdrove car--tellum about it-careful tryin to start it--mite damage valves

Aug 20, 2013 | 2001 Renault Sportwagon

1 Answer

Scenic power steering not working on right turn.


yes its the pump torque unit you need to replace your pump.sorry

Sep 19, 2009 | 2002 Renault Sportwagon

1 Answer

Torque settings for renault megane engine


Does anyone know the torque settings for the following Cam box(bolts), head bolts & crank shaft, the megane scenic is 2001.

May 01, 2009 | Renault Sportwagon Cars & Trucks

Not finding what you are looking for?
2007 Renault Scenic 2.0 Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

xxxxxx xxx

Level 3 Expert

4848 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...