Question about 2003 Mazda Tribute

1 Answer

Location of abs pressure switch on 2003 mazda tribute

Someone answered that the mazda abs pressure switch is mostlikely the problem were is this pressure switch located

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 4,536 Answers

Probly in the abs module-which is in the brake fluid line--a new module can cost 3000--if the fluid is dark changeit cause it destroys the modules--remembr u can stil brake w out antilock

Posted on Dec 15, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Where is the ignition coil pack located on 2002

The ignition power pack and (aka ignition coil) is located on the 2004 Mazda MPV at the end of each spark plug wire on top of the spark plug. The front ones are easy to replace and all 3 can be done in about 30 min. The back ones are another issue. I had to take off the intake manifold on the top of the engine to get to them. This was about a 5 hour job. The installation of the new unit is pretty simple once you gain access to them. you simply disconnect a clip on wire and take out one screw and reverse the process to put in the new ones. Factory units run about $80 each. You can get them at other locations in after markets for as low as $55. Good Luck.

Posted on Jul 23, 2009

  • 275 Answers

SOURCE: 2003 Mazda Tribute will start, idle rough for a

check the fuel filter air filter and vacuume lines if they all good make sure the spark plugs are making a bright blue spark

Posted on Jan 20, 2010

  • 617 Answers

SOURCE: where is the camshaft position sensor located on a

I have a diagram need email address to send to

Posted on Feb 07, 2010

  • 60 Answers

SOURCE: Mazda Tribute 2003 ignition switch

My 2001 Mazda Tribute ignition key cylinder was broken and locking up constantly. I would have to jiggle my key for up to 20 minutes to crank the car (it had nothing to do with steering wheel or shifter lock – the cylinder was busted). If at home sometimes I would resort to getting out a sander to vibrate the key while in the ignition and get it to turn. I was ready to take a sledge hammer to the car. I didn’t do any internet research on replacing the key cylinder until today because I figured it would be a big miserable job…but it wasn’t!!! To get to the cylinder, remove the 3 screws on the bottom side of the plastic steering column cover. Remove cover – use a screw driver to pry apart. Turn key to run position (don’t start engine). There is a pin on the bottom of the cylinder which is now exposed- take a small screw driver and push the pin in and pull on key. Cylinder should slide out. Get a new Ford Escape cylinder at the auto parts store (I payed $86, comes with two programmable keys), note: the parts store will not have one for Mazda, but Escape and Tribute are essentially the same car – many Mazda parts you can only get at the dealer for an outrageous price. Now do the following procedure...(note: you must have both original ignition keys for this to work)
1. Get some long needle nose pliers (forceps work best because they lock).
2. Grab the receiver knob that the end of the key cylinder normally engages near the center of the steering column. (Look in the hole that the cylinder was in)
3. Take one of the original ignition keys and insert it into the open cylinder hole alongside the pliers (this simulates the key being in the ignition/cylinder)
4. Push in and turn the pliers (ignition knob) and the first original key at the same time to run position - don't start the engine.
5. Wait for the key light to go off on the dash and turn pliers/key back to off position…note, if key light is flashing, tilt pliers slightly and try again.
6. Repeat with second original key and then the new key. You must go in this order and you must go from one key to the next in 10 seconds or less. This is how the car programs the new key. You may have to try a few times (I had to) and tilt the pliers a bit if they interfere with programming (key light flashing).
7. Once the key light comes on solid for a second or two and goes off with all three keys in a row (not flashing) then you have it. Repeat process with original keys and other new key.
8. Use pliers to align receiver knob to run position and Insert new key cylinder (remember to insert new key in new cylinder and align so cylinder will slide in properly - key should be turned in cylinder to run position).
9. Try out new keys…car should start! Install column plastic cover. You will still need to carry an original key to open the doors unless you fully trust that your keyless entry fob will always work. I would estimate this job to take about 20-30 minutes if you have the tools and new cylinder ready when you start. I was VERY skeptical when I tried this, but it worked great for me and I thank Mike at Cheapfobs.com blog a bunch!!…Good luck with yours!

Posted on Apr 25, 2010

  • 1 Answer

SOURCE: location of oil pressure switch.

how change oil pressure sensor in 2001 mazda mpv dx

Posted on Apr 02, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Anti lock brakes engage once in a while on2003 mazda tribute


Might have a bad brake switch, do you have any codes in ABS ? Does this happen when the vehicle is running and parked ? Do the brake lights stay on ?

Nov 25, 2016 | 2003 Mazda Tribute

2 Answers

My fuel emission light is showing on my mazda tribute 2003. Iam just about to trade it in and am wondering if there is cheap way to get it off before i trade it in


Search Results

    Failure of EGR Differential Pressure Sensor : Mazda Tribute ...

    repairpal.com > Problems > Mazda > Tribute
    Check Engine Light and Hesitation or Stumbling While Driving on Mazda Tribute ...this is my second egr valve and car is not picking up the right sped and when ... Mazda Tribute 2003, replacing burnt DPFE, connector bunrt, Need color pinout. ... Drivetrain · Electrical & Lights · Engine · Exhaust & Emissions · Heating & AC ...

    Check Engine Light Diagnosis Cost for Mazda Tribute ...

    repairpal.com > Estimator > Mazda > Tribute
    A Check Engine Light is turned on when the Mazda Tribute engine control module detects a fault in the emissions system. One or more diagnostic codes will be

Feb 05, 2016 | 2003 Mazda Tribute

1 Answer

Hazard light don't work


The hazard switch is located in the middle of the dashboard, above the radio. If has stopped working, you can order a replacement here:

SWITCH HAZARD DASHBOARD SWITCHES for Mazda Tribute 2001 2006 EC01664H0B

Aug 30, 2015 | 2003 Mazda Tribute

1 Answer

How to fix trunk latch on 2003 mazda tribute


try having someone push the switch while you use something like a screw driver pulling open the latch claws. this may be all it is.

Aug 07, 2014 | 2003 Mazda Tribute

1 Answer

Where is orifice tube on 2003 Mazda tribute


It is in the high pressure line going to the evaporator like everyone said. My Haynes manual made it look like it was at the connection right at the firewall but it is further upstream than that. There is a compression fitting upstream of the A/C tube fitting that you have to undo. Once you open that part you'll see the orifice tube. Hope this helps

May 27, 2014 | 2003 Mazda Tribute

1 Answer

Mazda Tribute 2003 ABS Light on but all is ok


the tone rings crack on those cars alot .dont let someone install and sell you a whole axle !!!

Dec 05, 2012 | 2003 Mazda Tribute

1 Answer

Oil pressure light is on, had oil changed but light still on, what could be going on? I have a 2003 mazda tribute.


Hi,
Please check your pressure sensor / transducer . Sometimes this part get failed that tell you wrong thing.
Regards,

Dec 15, 2010 | 2003 Mazda Tribute

1 Answer

The ABS light on my 2003 Mazda Tribute just came on; it has never done this before.


it may be a bad abs sensor. i would go to a mechanic that has a dignostic machine. it will tell you if sensor is bad or dirty or if the wire has come disconnected

Feb 05, 2010 | 2003 Mazda Tribute

2 Answers

Intermittent braking problem


yeah you mostlikey have a abs pressure switch problem. which helps in the power assist , and or the seal in the brake booster is going bad

May 27, 2009 | 2003 Mazda Tribute

1 Answer

Mazda tribute abs fault. abs light comes on & of when starting all ok. does not come on when driving, but you can feel the abs coming on when it shouldn't, intermittent. no fault codes, no abs light on...


These vehicles have a recall on the ABS system for faulty wiring. You may want to check with your local dealer to see if your vehicle is included.

Sep 16, 2008 | 2003 Mazda Tribute

Not finding what you are looking for?
2003 Mazda Tribute Logo

Related Topics:

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...