Question about Cars & Trucks

1 Answer

How do I remove middle armrest on 2008 Honda accord sedan

The middle console armrest between the front seats is torn and needs to be replaced. how do I remove the arm rest lid to replace the leather cover?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 311 Answers

Most likely 3 screws hold the armrest lid on.Towards the back.

Posted on Nov 12, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Front Seat Broke/Fold Down Arm rest broke

i have to 60/40 seat with a fold down console,

Posted on Dec 23, 2008

Fleetw00d
  • 31 Answers

SOURCE: Bumper cover removal

It is a little more complicated than that. There are two nuts below the headlight assemblies in the engine compartment. You will need to remove the battery and overflow bottle to get at the one on the passenger side. Remove the turn signals in the bumper, then there are 2 or 3 bolts holding a mounting bracket behind the each of the turn signals. There are a number of bolts with washer heads and reatiners on the underside of the bumper as the previous responder indicated.

Posted on Jan 26, 2009

  • 6 Answers

SOURCE: 2005 Honda Accord Front Bumper cover replacement

easy there is a screw on both sides were bumper and fender meet just pop back fender liner its a phillips head. Then pop hood remove clips on black trim infont of radiator. Underside where bumper goes under car remove those clips and 10mm bolts after all is removed bumper just pulls off ...... may have to give it a hard **** a few times but it will come off. Should only take 15-20min to remove if its your first time

Posted on Jul 03, 2009

ourhowse
  • 2007 Answers

SOURCE: 07 Expedition second row seat head rest cover plate removal

There should either be a little button at the base of the headrest that you push, or a small hole in the rod part, with a hole in it. Push in the hole with a pen, or a small nail to release the headrest.

Posted on Dec 27, 2009

  • 1 Answer

SOURCE: How do you remove the front bumper cover on a 98

remove front bumper on 1995 honda accord

Posted on Mar 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Center console removal


Well, this good to be interesting to say the least, and probably long as well. By my gm. service information your going to need to take out the front bucket seats so the sides of the console can come off.


Remove the left front seat . Refer to Bucket Seat Replacement .



1



Front Floor Console Extension Panel



2



Retainer Clip (Qty: 5) same for right side.



showgif.do?image=1875475





tif.gif








Callout







Component Name






Preliminary Procedure

Remove the right front seat. Refer to Bucket Seat Replacement .







1





Front Floor Console Extension Panel







2





Retainer Clip (Qty: 5)








Front Floor Console Accessory Trim Plate Assembly


Procedure

Use a flat bladed plastic trim tool in order to release the console accessory trim plate from the console assembly.



2



Retainer Clips (Qty: 5)



Remove the front floor console accessory trim plate. Refer to Front Floor Console Accessory Trim Plate Replacement.



1



Front Floor Console Accessory Housing Screw (Qty: 2)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

2 N?·m (18 lb in)



2



Front Floor Console Accessory Housing Assembly


Procedure




  1. Disconnect the electrical connectors.


  2. When replacing the front floor console accessory housing assembly, transfer all necessary components





  1. Remove the rght or left front floor console extension panel. Refer to Front Floor Console Extension Panel Replacement - Right Side or Front Floor Console Extension Panel Replacement - Left Side .


  2. Remove the front floor console cup holder housing. Refer to Front Floor Console Cup Holder Housing Replacement .



1



Front Floor Console Rear Trim Panel Screw (Qty: 1)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

2 N?·m (18 lb in)



2



Front Floor Console Rear Trim Panel



3



Retainer Clip (Qty: 4)


Preliminary Procedures


  1. Remove the front floor console accessory trim plate. Refer to Front Floor Console Accessory Trim Plate Replacement .


  2. Remove the right and left front floor console fillers. Refer to Front Floor Console Filler Replacement .



1



Front Floor Console Armrest Assembly Bolt (Qty: 4)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

9 N?·m (80 lb in)



2



Front Floor Console Armrest Assembly


Procedure

Position the armrest assembly out of the way leaving the electrical harness attached.



3



Front Floor Upper Console Trim Plate


Procedure

Lift the rear of the trim plate first, releasing the retainers securing the trip plate to the console assembly.



4



Retainer Clips (Qty: 4)



Front Floor Console Replacement (Enclave)





showgif.do?image=1858392





tif.gif








Callout







Component Name






Preliminary Procedures




  1. Remove the front floor console accessory trim plate. Refer to Front Floor Console Accessory Trim Plate Replacement .


  2. Remove the right and left front floor console extension panels. Refer to Front Floor Console Extension Panel Replacement - Right Side and Front Floor Console Extension Panel Replacement - Left Side .


  3. Disconnect the automatic transmission range selector lever cable. Refer to Range Selector Lever Cable Replacement .







1





Front Floor Console Screw (Qty: 2)




Notice: Refer to Fastener Notice in the Preface section.




Tighten

2 N?·m (18 lb in)







2





Front Floor Console Bolt (Qty: 10)




Tip

Before installing the right lower forward bolt, ensure that the console wiring harness is tucked below the fastener location to avoid driving the bolt into the harness.




Tighten

9 N?·m (80 lb in)







3





Front Floor Console Assembly


Procedure



  1. Note location and routing of the front floor console wiring harness prior to removal of the front floor console assembly to ensure proper reinstallation.


  2. Disconnect the electrical connectors.


  3. With the aid of an assistant remove the console assembly from the vehicle.


  4. When replacing the front floor console, transfer all necessary components.





h4hqqpweof7+aaaaaelftksuqmcc

arzs+0tf0j6faaaaaelftksuqmcc

Jan 10, 2015 | 2008 Buick Enclave

2 Answers

How do replace Honda Accord Armrest Vinyl Front Door Panels Armrest Covers


See the crack, the arrm rest is in 2 pieces remove the side it is snap ,there is 2 or 3 screws inside

Apr 22, 2014 | 1999 Honda Accord

1 Answer

Hi there, how do you remove the armrest on the front seats


Pop off the circle cap on the pivoting point of the armrest. You will see a 14mm bolt, remove it and then the arm rest should just pull out.

May 08, 2013 | 2006 Honda Odyssey EX-L

1 Answer

Need to remove center console to replace seat belt. After removing 12 screws, console is still firmly in place. What else has to be done?


  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest from the floor console.
  2. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  3. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  4. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  5. Lift the floor console from the front and rear console panel mounting brackets.

Feb 27, 2011 | 1996 Ford Explorer

1 Answer

I need to replace the cigarette lighter on my 1997 HOnda Accord. How do I get the panels covering it off so I can take the lighter out?


well you need to unbolt the arm rest first. push the driver seat and passenger seat all the way forward and there is a screw in the side panel of the armrest on both sides. open the armrest and there are screws under the small cover. removed cup holder just by pulling up on it and there is 3 screws under that. pull back on the entire armrest and get it out of the way. now you can see 2 screws at the end of the black panel for your shifter-remove. also remove ashtray and there is a screw behind that. now you should be able to pull out the panel that holds the lighter.

Oct 17, 2009 | 1997 Honda Accord

1 Answer

1990 gmc vandura. need to remove armrest from front seats


some are and some are not .call a big junk yard and ask them what the inner change is.

Mar 22, 2009 | 1990 GMC C2500

1 Answer

Replacing middle seat belt in 97 Dodge Caravan


If I recall correctly the belt actually is mounted behind the interior trim panel. It 1 piece on a short wheel base & 2 piece on a long. You must remove both seats (2nd & 3rd row) to hah room to remove the trim panel . BE CAREFUL the get very brittle and snap if you pull the wrong way

Mar 19, 2009 | 1997 Dodge Grand Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

433 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...