Question about Cars & Trucks

1 Answer

Change starter in 97 toyota 4wd tocoma 3400 engine

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Cars & Trucks Master
  • 2,485 Answers

Disconnect battery , undo starter motor wires undo two bo?t, s remove starter from motor,.

Posted on Nov 12, 2014

  • Richard Warren
    Richard Warren Nov 13, 2014

    Disconnect battery , undo starter motor wires undo two bo?t, s remove starter from motor,.

×

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 7353 Answers

SOURCE: Does a 1999 toyota tocoma

no, thats what the red oil light is for. Red light= STOP...RIGHT NOW.

Posted on Sep 02, 2011

  • 55 Answers

SOURCE: 97 toyota tocoma receiver dryer and lines

Unbolt the reciever dryer and the line remove and replace it and dont forget to use new Orings, Evacuate, check for leaks then recharge w dye type R134 freon. The dye will be in the system now so if it leaks anywhere you can easily find it with a UV detector light and glasses. Good luck.

Posted on Aug 24, 2009

  • 540 Answers

SOURCE: how to change spark plug on 2002 toyota tocoma 4

you have to remove the four ignition coils from the top of the valve cover and the plugs are down a hole underneath..

Posted on Nov 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We have a 2000 Toyota tocoma 4X4 V6 3400 it had a fuel injector #4 out we replaced it and put new plugs, wires and put it back together and it still runs rough


-Test all injector's resistant to find the problem before replace it.
-Possibly fuel pressure or bad spark plug line.

Good luck


mai

Aug 05, 2015 | Toyota Cars & Trucks

1 Answer

Does the crank shaft sensor control the spark on a toyota tocoma 1998


A bad pump sometime for a fast diagnosis get somebody to crank the engine and you take a hammer a knock on the gas tank 90 percent of the time the electric pump will start your truck its not a fix its a simple way to see that the gas pump is the problem change it

Mar 30, 2015 | 1998 Toyota Tacoma

1 Answer

How do you remove the starter on a 97 Toyota 4Runner?


1997 Toyota Truck 4 Runner 4WD 3.4L EFI DOHC 6cyl

STARTER - REMOVAL & INSTALLATION

On all engines except the 2UZ-FE, the starter is external, mounted in a conventional manner, alongside the engine block. One the 2UZ-FE, however, the starter is mounted in the 'V' of the engine, between the cylinder head banks. The entire intake manifold assembly must be removed to access the starter motor and solenoid. (Toyota calls the solenoid a "magnetic switch.")


Except 2UZ-FE Engine

b08302c.jpg

Fig. Unfasten the starter mounting bolts . . .

97360a1.jpg

Fig. . . . then pull the starter toward the front of the vehicle to remove it (other components removed for clarity)
  1. Disconnect the negative battery cable.
  2. Remove the nut and disconnect the battery cable from the magnetic switch on the starter motor.
  3. Detach the remaining electrical connections at the starter.
  4. Remove the nuts and/or bolts securing the starter to the bell housing, and then pull the starter toward the front of the vehicle to remove.
To install:
  1. Insert the starter into the bell housing being sure that the starter drive teeth are engaged with the flywheel teeth, NOT jammed against the flywheel.
  2. Tighten the attaching hardware to 29 ft. lbs. (39 Nm) and replace all electrical connections.
ec2db09.jpg



Fig. Exploded view of a common starter mounting found on Toyota trucks
  1. Connect the positive battery cable (starter wire) to the starter.
  2. Connect the negative battery cable.
2UZ-FE Engine

baf1623.jpg

Fig. The starter motor on this 2UZ-FE engine is installed under the intake manifold between the cylinder heads, making it a lengthy procedure to perform
  1. Disconnect the negative battery cable.
  2. Remove the cosmetic/acoustic engine cover.
  3. Disconnect the accelerator cable and intake air connector.
  4. Remove the intake manifold assembly. For additional information, please refer to the following topic(s): Engine Mechanical, Intake Manifold.
  5. Remove the two bolts holding the starter motor to the engine block and lift the starter away from the block.
  6. Detach the electrical connectors from the starter and remove the starter from the vehicle.

I hope help you with this (rated this help). Good luck.

Sep 25, 2009 | 1997 Toyota 4Runner

1 Answer

97 toyota tocoma receiver dryer and lines


Unbolt the reciever dryer and the line remove and replace it and dont forget to use new Orings, Evacuate, check for leaks then recharge w dye type R134 freon. The dye will be in the system now so if it leaks anywhere you can easily find it with a UV detector light and glasses. Good luck.

Jun 23, 2009 | 1997 Toyota Tacoma

1 Answer

Easy way to replace starter on 97 blazer s10


I need to change the starter on a 97 Blazer s10 4wd . it a v6 vortex engine. What is the esiest way without jacking up the engine.

May 29, 2009 | 1997 Chevrolet Blazer

1 Answer

Can't shift out of 4WD on the fly in my 97 Toyota 4runner


To pe perfectly honest, the 4WD engeagement.disengagement is compromised when tires are not the same mfgr and tread depth.

You might get lucky with one additional tire, but I am not confident that this will "fix" it; it may help, however.

The graciousness of a FixYa rating would be greatly appreciated.

Dec 26, 2008 | 1997 Toyota 4Runner

1 Answer

How to check trans oil level


I assume that you have a 6 cyl.There are two plugs on the trans pan.the big one is the drain and the small one is the check plug.There is a fill on the side.The trans uses ws fluid which is what you need to use.What i do is remove the check plug and add fluid until it comes out.Then start the engine and let it warm up, the recomended temp is 97 to 115 degrees f or 36 to 46 degrees c.As it warms up the fluid will come out,once it reaches the temp range put the plug back in.I use a computer to monitor the temp but a temp gun on the pan will do.

Nov 28, 2008 | 2007 Toyota Tacoma

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...