Question about 2007 Chrysler Pacifica

1 Answer

How do i put the lower part of the bumper back on my 2007 chrysler pacifica

Just need to kno how to put it back on

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

  • Expert
  • 64 Answers

You need push pins from dealer they r only plastic plugs

Posted on Nov 29, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

turo1000
  • 18 Answers

SOURCE: program instruction garage door opener in 2005 chrysler pacifica

if your garage motor have rolling codes you need to put your car inside garage near the motor leave ignition on go to the motor locate learn button press it then quickly go to the car and press and hold one of the buttons for approximately 30 sec or until it start blinking rapidly, if you have a regular motor take one hand held opener go inside car ignition on same time press open button on handheld remote and on the car button 30 sec and it should be programmed.

Posted on May 18, 2009

  • 47 Answers

SOURCE: 2006 Chrysler Pacifica serpentine belt routing

here are a couple diagrams...
1e7d361.jpg

011a835.jpg

If you need anything else, let me know.

Posted on Mar 19, 2010

tiresmoke
  • 68 Answers

SOURCE: 2007 Chrysler Pacifica heater blows cold air - A/C

Hello, seems like your thermostat may be stuck open. After the vehicle been running more than 10min feel the upper radiator hose it should be hot to the touch and if not a new thermostat is needed.

Posted on Mar 27, 2010

  • 1024 Answers

SOURCE: serpentine belt routing for 2004 chrysler pacifica

here it is

98c85ed.gif

Posted on Apr 13, 2010

  • 6 Answers

SOURCE: how to replace the rear bumper cover on a Chrysler

1. Open liftgate. 2. Remove both taillight assemblies by removing 2 hex-head bolts located in the area revealed when the liftgate is opened. 3. Remove 4 plastic retainers on the very bottom of the bumper cover in the rear. 4. Remove 2 phillips head screws in the wheel well rear lip. 5. Remove 4 pop-up plastic retainers in liftgate area. Use two screw drivers to lift the head and then pull the entire retainer out. 6. Remove a hex-head bolt from each side in the area revealed when the taillight assembly was removed. 7. Bend the bumper cover outward on each side to clear the wheel well lip and remove the bumper. Have a blanket or carpet on the ground to protect the bumper. 8. Remove metal clips from tabs that connect the upper bumper cover to the lower bumper cover. 9. Drill out pop-rivets that connect upper bumper cover to lower bumper cover. 10. Push tabs out of slots to separate the upper and lower bumper covers. 11. Release tab locks on chrome trim pieces and remove from upper bumper cover. 12. Reverse this process to replace the bumper cover.

Posted on Sep 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is my TCM located in my 2004 Chrysler Pacifica all wheel drive


its located near the battery , generally inside front bumper driver side

May 25, 2017 | 2004 Chrysler Pacifica

1 Answer

Replaceing front bumper chrome trim


Put a couple lines of silicone calk on it and stick it on there

Aug 02, 2016 | 2007 Chrysler Pacifica

2 Answers

Why does my 07 Chrysler Pacifica feel like its going to vibrate off the road with acceleration at 40 - 60 Mph?


2007 Chrysler Pacifica Problems, Defects & Complaints

www.carcomplaints.com/Chrysler/Pacifica/2007/
5 days ago - The 2007 Chrysler Pacifica has 97 problems & defects reported by Pacifica owners. The worst complaints are engine, transmission, and ...‎Engine - ‎TSBs 13 - ‎Crash Tests 2 - ‎Defect Investigations 2

Aug 03, 2015 | 2007 Chrysler Pacifica Touring

2 Answers

Chrysler pacifica 2007 cannot put much fuel in at a time. gas guage drops from half tank to empty in seconds


If you can't put much fuel in i's probably not empty! If there is not a big puddle of fuel underneath then your guage is broken.

Jan 04, 2015 | 2007 Chrysler Pacifica FWD New Cars

1 Answer

2007 chrysler t&c. have no control of heat or air cond. bought ambient temp sensor need to know location for install


This sensor is located behind the front bumper cover, if yhou open the hood and remove the screws holding the top of the bumper cover down you should be able to reach down and get to the bolt. It mounts to the drivers side of the lower radiator support. If you have the right tools you may be able to get to it from the lower part of the bumper cover through the lower grill section.

Apr 30, 2013 | 2007 Chrysler Town & Country LX New Cars

1 Answer

I have a 04 Chrysler Pacifica. My lower bumper came off now I am left with no lower bumper plus the plastic part of the car it was attached to came off. My upper bumper is in tact. I am trying not to...


Used ones are 100 to150 there are two screws by the rear tail lights. Push pins across the bottom and a screw in the bottom of each wheel well. Open tailgate and pull up

Sep 23, 2011 | 2004 Chrysler Pacifica

1 Answer

How to replace the rear bumper cover on a Chrysler Pacifica


1. Open liftgate. 2. Remove both taillight assemblies by removing 2 hex-head bolts located in the area revealed when the liftgate is opened. 3. Remove 4 plastic retainers on the very bottom of the bumper cover in the rear. 4. Remove 2 phillips head screws in the wheel well rear lip. 5. Remove 4 pop-up plastic retainers in liftgate area. Use two screw drivers to lift the head and then pull the entire retainer out. 6. Remove a hex-head bolt from each side in the area revealed when the taillight assembly was removed. 7. Bend the bumper cover outward on each side to clear the wheel well lip and remove the bumper. Have a blanket or carpet on the ground to protect the bumper. 8. Remove metal clips from tabs that connect the upper bumper cover to the lower bumper cover. 9. Drill out pop-rivets that connect upper bumper cover to lower bumper cover. 10. Push tabs out of slots to separate the upper and lower bumper covers. 11. Release tab locks on chrome trim pieces and remove from upper bumper cover. 12. Reverse this process to replace the bumper cover.

Feb 16, 2010 | 2006 Chrysler Pacifica

Not finding what you are looking for?
2007 Chrysler Pacifica Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...