Question about 2003 Buick Rendezvous

1 Answer

What is the torque settings for 2003 buick rendezvous centre head

Posted by on

  • Craig Fisher Nov 11, 2014

    Call the service dept at the closest dealer, they can tell you exactly, no guess work !

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Buick Master
  • 906 Answers

Answered but in general the bolts are 44 Ft. Lbs and 90 degree turn. In some cases replacement bolt kits will have the torque information on the box

Posted on Dec 19, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 50 Answers

SOURCE: 2993 Buick Rendezvous

The dryer that you are talking about is mounted to the a/c condensor assy. infront of the radiator. I do not think that there is a low pressure switch by the drier on this particular model though. This particular vehicle uses an evaporator temp. sensor to control the operation, much like most cars using a low pressure switch. The problem with this type of set up is that you must remove the entire dash assy. to get to the sensor. If you can give me a little more info on the problem that you are having, I will be glad to further assist you.

Posted on Aug 20, 2008

  • 3 Answers

SOURCE: what are the torque specs for the intake manifold

the torque spec's require you to tightened to 10 ft lbs and then tighten another 30 degress which will give you about 12 to 15 ft lbs of torque. make sure that you start in the middle and work your way out when tightening manifold because it will crack easily.

Posted on May 02, 2010

Testimonial: "Thank You!"

Tooldude1969
  • 106 Answers

SOURCE: how to change regulator motor on a 2003 buick

from Ehow.com. Long answer
All Buick automobiles now have powered windows for both front and back doors. These powered windows use a motor attached to a continuous screw that lifts and lowers a lattice device for opening and closing the window. Each window also has a window regulator to tell the motor when to stop both lowering the window and raising it into place. Occasionally, this regulator will become faulty and need to be replaced. Although not a difficult procedure, it does mean having to disassemble the Buick's door.
jQuery('.intro .thumbnail').each(function(i,e){ jQuery(e).find('img').one('error',function(){ jQuery(e).remove(); }); });

    Door Armrest
  1. The first thing to do is remove the Buick's armrest on the door. Underneath the armrest, hidden from view, are large screws that go all the way into the doorframe. Remove all of these screws and the armrest will come free. Once it's loose, carefully disconnect all the wires to the remote control switches. The driver door armrest will have more wires than the other doors. Door Panel
  2. Once you've removed the armrest, you can take off the inside door panel. Start by going all the way around the door's edges and removing all the fasteners. Once you've removed these may find some clips holding the panel tight, depending on your model Buick. Carefully unfasten these and then work the door panel up off its guide at the top of the door next to the window opening and around the car door handle. If your Buick has a door-mounted nightlight, disconnect the wires to the accessory. This will give you access to the door's interior. Removing the Old Regulator
  3. Inside the door there are two components with electrical wires: the motor and the regulator. The motor is attached to a long threaded bolt. Remove the wires connected to the regulator and then the screws mounting the regulator to the doorframe. Be careful not to scratch the window with the screwdriver when working in these close quarters. Once the regulator is free inside the door, lift it out of the door. Installing the New Regulator
  4. Installation is just doing the removal procedure in reverse: put the regulator in the door, secure it, connect the wires (no need to solder; the wires are connected with tabs), and reattach the door panel, the switch wiring and the arm rest.

    It should take no longer than an hour to complete this project. One quick warning, however---never force or strain any part to remove it. If a component does not come free easily, then check again for an extra screw or retaining clip. Don't get frustrated and break something that ends up being more expensive than the cost of the new regulator!


Read more: Best Way - Buick Window Regulator Installation Instructions | eHow.com http://www.ehow.com/way_6510604_buick-window-regulator-installation-instructions.html#ixzz0uQJxAMM2

Posted on Jul 22, 2010

  • 1 Answer

SOURCE: Replace fuel pump on 2003 Buick Rendzvous

What parts are needed to replace the fuel pump on a 2003 buick rendzvous?

Posted on Sep 28, 2010

  • 37 Answers

SOURCE: how to remove alternator in 2003 buick rendezvous

here is a pdf file showing you how to remove it.

http://www.mediafire.com/?xa0wbaadt3t3tvr

thanks and please rate my answer

Posted on Jan 05, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 buick rendezvous rocker arm torque spec


14 N.m (124 lb. in.) plus 30° This what the book says. But 10 foot pounds plus 30 degrees.

Oct 15, 2016 | 2003 Buick Rendezvous

1 Answer

How do I take the stock CD player out of 2002 Buick rendezvous


Remove the face and there are two screws holding it in with anti theft heads which requires a special torque bit ,may be an earth strap at the rear.

Sep 29, 2015 | 2002 Buick Rendezvous

1 Answer

What is settins and torque for centre head of 2003 buick rendezvous


I need more information, what engine for example. You should be able to get that information from any garage that can get the information from the car.

Nov 11, 2014 | 2003 Buick Rendezvous

1 Answer

HEAD BOLT TORQUE SPECIFICATION


On the 3.4L V6 The head bolts require two stage torque process to Achieve 44 ft-lbs torque.
First tighten all of the all of the head bolts to 30 ft-lbs.
Then proceed to 44 ft-lbs for each.

Apr 05, 2011 | 2002 Buick Rendezvous

1 Answer

How to replace a rear wheel bearing on the rendezvous and does the rear end need to be alined


Loosen the lug nuts. Jack up the car and pull off the wheel and brake drum.Unplug the electrical connector from the hub assembly Unscrew the four Torx head bolts that retain the hub assembly. Holes in the hub provide access to the screws. Remove the hub. Bolt the replacement hub assembly into place. Torque the Torx head bolts to 63 ft. lbs... and it would be best to realign after the work is done to ensure the "tow" is not off

Feb 19, 2011 | 2003 Buick Rendezvous

1 Answer

2003 Buick Rendezvous Torque spec's for the Valves Please?


You will have to buy a Chiltons manual, or go to a dealer and buy one that is specifily for your vehicle to find the valve clearance.

Nov 10, 2010 | 2003 Buick Rendezvous

1 Answer

Need torque setting for rear hub assembly on 2003 Buick Rendezvous


BEARING TO HUB TO THE AXLE BEAM BOLTS TORQUE IS 63 FT LBS.FOR DRUM BRAKES 96 FT LBS WITH DISC BRAKES.

Apr 18, 2010 | 2003 Buick Rendezvous

2 Answers

Head replacement


You can do it. You will need a good set of basic hand tools. The only special tool you should need is a torque wrench. If you have never done this, I suggest buying a manual

Jul 04, 2009 | 2002 Buick Rendezvous

Not finding what you are looking for?
2003 Buick Rendezvous Logo

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...