Question about 2008 Suzuki Forenza

1 Answer

How do you fix a slave cylinder on a 2008 Suzuki froenza

I have lost my cluch to my car and ive tried bleeding it but with know luck it still leaking im trying to figure out how to chang it and is there a way to get to it because mine is in side the tranny

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 477 Answers

If it is inside the transmission then it is best left to the experts unless you have a vehicle lift

Posted on Nov 11, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 51 Answers

SOURCE: clutch cylinder inside car is it broke

you have to bleed the air out of it. If there is not fluid leaking from the master cylinder on the firewall.it can leak on the inside of car or the out side if the master cylinder is bad.first make sure the reservoir stays full then open the bleeder on slave cylinder. this is called gravity bleeding. once fluid comes out, tighten bleeder, pump pedal one time loosen bleeder while holding clutch pedal down and then tighten. do this repeatedly until no air comes out. you can pump pedal several times,then hold and bleed however you like but I have better luck with individual pumps. just make sure that the lines hooked to slave cylinder are tight and there are no air leaks. and that the line does not go below the slave cylinder because sometimes air gets trapped in the lowest part of system.

Posted on Jan 12, 2009

moparownr
  • 667 Answers

SOURCE: im having difficulty in bleeding a cluch o a ford

clutch systems bleed just like brakes, if you have an external leak at the clutch master cylinder, then bleeding will be difficult, it should be replaced. I use a two person bleeding system, I fill the master, crack the bleeder screw open and have my 2nd push the clutch down and hold it, then I close the bleeder and tell my 2nd to release the pedal, repeat until no air is present.

Posted on Apr 08, 2009

  • 18 Answers

SOURCE: How to bleed a slave cylinder on a Saturn?

tyhe bleeder is down on the transmision

Posted on May 15, 2009

  • 1 Answer

SOURCE: dodge dakota

i have a 2000 dodge dakot and can not bleed the slave cly how do i do it

Posted on Jul 19, 2009

  • 422 Answers

SOURCE: I have a 1987 Ford Ranger that I replaced the

your throwout bearing is probably bad (most likely)

Posted on Nov 19, 2009

Testimonial: "Thank you for your response. I will look into that possiblity as well but it was replaced along with the slave cylinder."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I put a new slave cylinder in my 99 dodge dakota & now i have no cluch at all


find someone who knows how to bleed a system, just like bleeding brakes but with only 1 wheel cylinder. Helps if you tie a rope on the clutch pedal so the person inside the car can pull it back up when he is doing the pumpings between bleedings. Do not let a woman do that for you.
There could well have been a thin crush washer between the line and the slave which you neglected to replace with a new one when you reassembled, if that is not there you will never get it bled. It crushes down when you tighten it to seal the system and it only crushes once

good luck.

Aug 26, 2011 | Dodge Dakota Cars & Trucks

2 Answers

Where is the slave cylinder


the slave cylinder looks almost like a small brake master cylinder usually near the rear of the engine compartment and will have a fill line just the same. It is used in the hydraulic operation of engaging/disengaging the clutch from the pressure plate

Apr 29, 2011 | 1992 Nissan Pathfinder

2 Answers

I was driving and the clutch felt weak now it won't go into gear. I bled the cluch and still noting. Do I need a new clutch or throwout bearing?


Check that the clutch release level is actually being moved by the slave cylinder.

If not, replace the slave cylinder if it appears to be leaking. The clutch master may be leaking also, but this would be unusual for a mere 2006. I'd guess its the slave cylinder.

If so, your clutch has failed.

Jan 07, 2011 | 2006 Suzuki Forenza

1 Answer

1994 4X4 pickup cluch fluid line bleeding . Fliud cyliner has fluid but cluck doed not work


Check the clutch master and slave cylinders for leaks, look behind the rubber boots as the boots can trap the fluid. If all of that is good then you use normal bleeding procedures: step on the clutch, have someone open the slave bleeder to let fluid and any air out, close slave bleeder, repeat.

Feb 19, 2010 | 1994 Toyota Pickup

1 Answer

Cluch wont bleed new cluch fitted 14 months ago ,no pressure at on cluch peddle will not go into any gear


bad slave cylinder/hydrolic?-bad pressure plate/throughout bearing
replace them it should fix it.ive been there before!!!!!!!!!!

Nov 21, 2009 | 2000 Ford Focus

1 Answer

CLUCH FLUID LIK


if you have a leak in the cluch fluid is it the master cylinder or the slave cylinder leaking??? you may be ably to get a repair kit for it or replace the hole unit then bleed it through

Oct 30, 2009 | 1990 Jeep Wrangler

2 Answers

Peressure bleed a cluch pt 2003


Try a manual bleed first, as it may achieve the same result without the hassle of pressure bleeding.
Fill the master cylinder resevoir, keep it topped up while cracking open the slave delivery line- wait for a steady dribble of fluid to come through - a couple of gentle pumps of the master cylinder will help the process.
Then move to the slave cylinder bleed nipple - crack it open and repeat the process above.
Once you get a bit of pedal pressure back, it's fairly straightforward to complete the bleed process.

Oct 06, 2009 | 2006 Chrysler PT Cruiser

1 Answer

Cluch


To bleed the clutch, there is a little slave cylinder next to the transmission, on that slave cylinder there is a bleed nipple. Undo that put a pipe on it that fit nicely, put the other end of the pipe in a jar with some brake fluid. When you have got that right, pump the clutch pedal up&down. but keep a eye on the fluid in the reservoir under the hood, keep pumping the pedal until all the air bubbles are gone. when they have all gone tighten up the bleed nipple without taking the pipe off. then you are done.

Good luck!!

Jul 19, 2009 | 2002 Chrysler Voyager

1 Answer

Cluch stuck to floor.


Have you tried bleeding the master cylinder first? There should be a bleeder valve down on your tranny close to where your master cylinder line hooks in. You need 2 people to do this properly or you can buy a special valve from an auto parts store and do it yourself. If any air has gotten into your lines, your clutch will go to the floor. Tranny fluid is cheaper than buying both slave and master cylinders. Plus, if you replace them, you'll have to bleed the system anyway.

May 21, 2009 | 1993 Ford Probe

1 Answer

Im having difficulty in bleeding a cluch o a ford


clutch systems bleed just like brakes, if you have an external leak at the clutch master cylinder, then bleeding will be difficult, it should be replaced. I use a two person bleeding system, I fill the master, crack the bleeder screw open and have my 2nd push the clutch down and hold it, then I close the bleeder and tell my 2nd to release the pedal, repeat until no air is present.

Apr 08, 2009 | Ford Club Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...