Question about Ford Fusion

1 Answer

Ford fusion no power in passage side door locks.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 1,268 Answers

Pull the door panel and check the ground is connected and tight. Clean the connection before panel is replaced and tighten the screw.

Posted on Nov 22, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 295 Answers

SOURCE: The door master window switch

Check the ground attach a 12v test light to battery positive and prob the ground circuit. If it does not light up check the wiring in the door jam were the hinge is seen lots of broken wires in there before.

Posted on Jul 20, 2009

ZJLimited
  • 17970 Answers

SOURCE: car door will not open

Review this information about ZJ-Secc-8P-Power-Door-Locks

Or check in the ZJ-Secc-8W-Wiring-Diagrams (Diagram ZJ 89 / Page 130 and next)

Good luck... remember rated the help.

Posted on Aug 11, 2009

Testimonial: "Thank you so much for your advise. I truly appreciate it. God Bless, Jane"

  • 12 Answers

SOURCE: My 2001 ford windstar passenger door locks and

have you checked the locking mechisnium ithey can be faulty

Posted on Mar 23, 2010

  • 5 Answers

SOURCE: 2006 Ford Fusion. Left front door inside handle

This link is from the handle to the latch. The door panel has to be removed in order for this problem to be fixed. The linkage is inside the door panel, it is a small diamater metal rod called a link. If you do the job yourself be careful not to break the door panel. In a shop, the labor is 1 hour for the job & if any, parts will be a seperate charge.

Posted on May 08, 2010

  • 87 Answers

SOURCE: how to change the passager headlight on 2008 ford

you must remove the bumper

Posted on Jul 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

Door handle repair for Ford fusion


The door handle will not allow unlocking from the inside. This is a common problem with the Ford Fusion 2007 to 2012 and other cars. A cheap piece of plastic breaks that connects the lock lever with the door handle. You can roll down the window and unlock from the outside or hold both levers together and pull open from the inside. This is a very simple repair. Go to any of many web sites for auto parts and buy a replacement. I bought a Dorman 81702 Ford/Lincoln/Mercury Interior Front Driver Side Replacement Door Handle. I popped off the lid that covers a hidden screw inside the recess of the door handle. You have to use a torque bit to unscrew the screw. I then unscrewed the torque screw holding the upper part of the door panel that is opposite the door hinge. The upper part of the door panel can be be carefully pulled away with moderate pressure allowing access to the door handle mechanism. One more bolt holds the door handle part in place. Pull out the broken door handle part, remove the locking cable and put in the new part. Reverse the process to finish up. The whole process took about 10 minutes.

on Sep 18, 2015 | 2010 Ford Fusion Hybrid

1 Answer

2009 ford fusion left ft door wont open from inside power lock works must roll down window to open with outside handle


Either the linkage connected to the handle has come off, or the piece on the handle inside has broken. You will need to remove the panel from the door and repair or replace the handle.

Mar 28, 2014 | 2009 Ford Fusion

2 Answers

2006 Ford Fusion right rear door will not lock with remote


Sounds like the electric actuator is not connected inside the door.

Aug 20, 2012 | 2006 Ford Fusion

1 Answer

I have a 2008 ford fusion along with 2002 ford taurus. Just for the testing purposes I was trying to program the taurus keyless remote into the fusion, and now the single keyless remote is working on both...


cycle your ignition 8 times on and off really fast then on the eight time you cycle the door locks should lock and unlock,then hit the lock and unlock button on your fob that should set it just for one car. if you try to reset the fusion key your dealer will charge you alot of money

Sep 26, 2010 | 2008 Ford Fusion

2 Answers

2006 Ford Fusion. Left front door inside handle


This link is from the handle to the latch. The door panel has to be removed in order for this problem to be fixed. The linkage is inside the door panel, it is a small diamater metal rod called a link. If you do the job yourself be careful not to break the door panel. In a shop, the labor is 1 hour for the job & if any, parts will be a seperate charge.

May 08, 2010 | 2006 Ford Fusion

5 Answers

2006 Ford Fusion inside door handle stopped working


The plastic door handle is broken.
You will need to get a replacement door handle.
Go to http://www.flickr.com/photos/gtppilot/sets...57607539089979/
This should help. It is a set of photographs and instructions to do the job of replacing the handle.

Good luck.

Rgrdrake

Nov 11, 2008 | 2006 Ford Fusion

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...