Question about Cars & Trucks

1 Answer

Repair ivory clad walking stick from lake toba

The centre of clad shaft seems to be brocken in the middle

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Have it filled with resin, the kind that are used to fix windshields.

a windshield repair shop can do this for you.

Posted on Nov 11, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

In construction, what is Riven Cladding? How does Riven cladding differ from any other form of cladding? In other words, what is a riven?

I just did a search under Yahoo and it came up with details, and pictures. better for you to look than for me to try and detail it to you.

Sep 11, 2017 | Cars & Trucks


How clean your Ford Edge chrome clad wheels so they balance

The Ford Edge chrome clad wheels are causing balancing issues and costing everyone money in unbalanced and prematurely worn tires or even wrongly thinking the tire is bad. Watch this video and discover how the chrome clad wheels can be cleaned and balanced.
Are your Ford Edge Chrome Clad wheels costing you money

on Mar 28, 2016 | Ford Cars & Trucks

1 Answer


some had dip stick to check and fill from which is in middle of engine and trans at front (where engine joins trans) black plastic lock over tang, engine dip stick is yellow. other model transmissions had a filler bolt hole which is in left side of gear box right next to where left drive shaft goes into gearbox even though its auto. some manual boxes had this same filler plug location and even on right side of box next to right drive shaft.

Feb 21, 2014 | Holden Cars & Trucks

1 Answer

The Serpentine belt keeps walking off the Crank shaft pulley by one rib as if the pulley moved away from the engine.. Is this where the harmonic balancer is. If so, is it difficult to change?

Before you change anything,,check and see if everything is in line..Also feel all the pulleys and make sure everything turns ok...If the powersteering pump has been replaced,,sometimes the pulley was not pressed on far enough..If it seem to be the harmonic balancer make sure its not damage and the bolt in the middle is tight...If you remove it..You remove middle bolt,,then you have to use a puller to remove the harmonic balancer itself..unusuall for the harmonic balancer to be bad unless it was hit by something

Sep 20, 2011 | 2005 Ford Taurus

1 Answer

I need to remove the rear wiper arm from a 2007 Pontiac Torrent. I have removed the nut, but I can't seem to get the arm off of the motor shaft. Any tips??? I am trying to change out the rear wiper...

a small puller is best, but if you use a penetrating oil on the shaft, and a couple of screwdrivers (use rags underneath so you do not damage paint) you can walk it off the shaft.

Aug 07, 2011 | Pontiac Torrent Cars & Trucks

1 Answer

Slide door doesnt open from ouside

If the latch works but the door seems to be jammed, take a look at the bottom rear corner of the door. do you have the factory cladding and/or running boards on the van? If so, the bottom rear corner of the door is likely to be hitting the cladding where it wraps around into the bottom of the opening. Go inside the van and with a helper on the outside pulling the door open, push against the door to open it. Next, look at the cladding where it wraps around into the door opening. You will probably see where there is some wear to the paint, but not necessarily. What you need to do is ease the cladding towards the rear of the vehicle. Think of it as sliding it backwards along the body. it doesn't take much, only about a millimeter or two. I used a screwdriver against the cladding where it interfered, and nudged it with the BFH. It worked beautifully for about 6 months, at which time I just did it again.

Jan 11, 2011 | 1997 Chevrolet Astro

2 Answers

How do i centre the clutch on 98 cavalier

what i usually do is look into the hole on the clutch and line it up with the spigot bearing hole and then tighten it up

Mar 08, 2010 | 1998 Chevrolet Cavalier

1 Answer

My 2004 touareg is making screaching noise . what could it be?

if it occurs when you are moving it is most likley to be the propshaft centre bearing i have done a cant get the bearing seperate im affraid its the whole shaft...hope this helps.

Feb 20, 2009 | 2004 Volkswagen Touareg

2 Answers

I paid for an answer about my 89 ford ranger drive shaft and did not get one. Can I get my money back or do I need to contact Pay-Pal??

To replace the centre bearing you first remove driveshaft from vehicle.
Pull the shaft apart at the middle universal joint.
On the back of the section that has the centre bearing you will see a nut that holds the uni ears onto the shaft.
Undo the nut and remove the ears. Then press the centre bearing off the shaft and reassemble with new one.
Hope this is more helpful.

Jan 01, 2009 | 1991 Ford Ranger Supercab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

14479 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides