Question about Cars & Trucks

1 Answer

2006 5.7 jeep cherokee engine just keeps running when switched off

When i go to turn the engine off it just keeps running i have to disconnect the battery to stop it can you help please

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

May be it can be the ignition switch or body control module

Posted on Nov 10, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 412 Answers

SOURCE: 02 grand cherokee fan keeps running after the engine is shut down

there is a fuse in fuse block underhood..but it sounds like a stuck cooling fan relay..is located on pass side front frame rail..you have to remove both headlamps and front bumper cover to access relay

Posted on May 17, 2009

BillB-SA
  • 2761 Answers

SOURCE: My 1999 Jeep Grand Cherokee Laredo radiator fan

There's a thermostatic switch that kicks the fan on and off. It is apparently shorted, causing the fan to run continuously. Check with your local auto parts store -- you be able to replace the switch without having to replace the entire fan assembly. In the meantime, pulling the fuse is a lot better than disconnecting the battery. You won't lose computer memory, clock, stereo memory, etc.

Posted on Oct 20, 2009

  • 94 Answers

SOURCE: 2004 Jeep Grand Cherokee. Keeps stalling, engine

P0505 means the whole Idle Control system, not only the IAM. Check all related sensors (i.e. crankshaft sensor). Check with a voltmeter direct at the connector of the IAM if you get any signal. Remove the IAM from the TB, connect him, let someone switch your ignition key to ON. The IAM need to drive in/out for a short time to find the right position. Hold the IAM near a hard part, that they cant drive out completely! If IAM works fine, check the fuel pressure, check and clean your TB ( if not done yet). If that doesn't work, come back again please

Posted on Oct 27, 2009

  • 3640 Answers

SOURCE: 2002 jeep grand cherokee with 4.0 engine will die but restart

p0340 is the cam shaft sensor, this will cause it to cut off while driving, hardtime starting, p0351 is the ignition coil A primary/secondary curcuit mal function. p1391 is ignition system misfire, this could be plugs, wires, or coils. first of all have the cam sensor changed and it may correct the rest of the codes. when fixed turn light off with obd2 scanner. if you do not have one, then any auto parts store will erase the codes fo free of charge.

Posted on Jan 21, 2010

  • 10 Answers

SOURCE: The toyota Cmry engine won't stop unless battery is disconnected.

i have the same problem with my corolla 2002 I turn off the keys and put it out and the engine still running, I uplug the EFI fuse and the engine stop, I guess I need to replace the ignition.. or i'm wrong???

Posted on Feb 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i know there is a kill switch on my jeep because it run out of oil and it turn off and won't turn back on if so where is it locate?


check oil pressure
using a real gauge at the engine block sender hole.
do so cranking not started.
0 PSI?
the sender (icon magic) goes on at below 3-5PSI
and 5psi is doom levels.

Feb 26, 2015 | 2006 Jeep Grand Cherokee

1 Answer

Hi, i have a grand cherokee 5,7 from 2006. The lights in the instrument panel, and the exterior lights keep flashing when the engine in turned on. I cannot adjust the lights in the instument panel neither....


I have a similar problem - every once in a while all of my dash lights flash on like the car is trying to conk out/stall (I have a 2006 Jeep Grand Cherokee) - the car has no loss of power and runs fine, just all of the dashboard lights and warnings come on like its going to stall. Happens on dry days, wet days, cold days, warm days - at least 3 times a month. trouble is, because its intermittent no one can find the problem.

Sep 12, 2012 | 2006 Jeep Grand Cherokee

1 Answer

2006 jeep cherokee radio screen has lines running thru it, radio works fine. Is this a fuse problem?


No. It's a radio screen problem. Being an 06, if it still works, keep listening.

Jul 01, 2011 | 2006 Jeep Grand Cherokee

1 Answer

I have a 95' Jeep Grand Cherokee Limited with a


Are you check your previoud questions: check_engine_error

Keep us updated.

Jun 07, 2011 | 1995 Jeep Grand Cherokee

1 Answer

The radiator fan in my Jeep Cherokee keeps running after I turn off the engine. How can I get it to quit running?


You will have to take out the fuse to get it to stop. You could possibly wire it up with a toggle switch to turn it on and off.

Feb 13, 2011 | 1999 Jeep Grand Cherokee

1 Answer

2006 Jeep HEMI Engine. Very slow starting in cold weather!


try turning key on for about 15 seconds before you try to start

Feb 11, 2010 | 2006 Jeep Grand Cherokee

1 Answer

How do you reset the perform service message after changing the oil in a 2006 Jeep Grand Cherokee?


http://www.jeep.com/en/owners/manuals/index.html?year=2006&nameplate=Grand%20Cherokee

That should allow you to download a copy of the owner's manual that will detail the reset procedure.

Basically, on Jeep products you

To reset the oil change indicator system (after
performing the scheduled maintenance), refer to the
following procedure:
1. Turn the ignition switch to the ON position (Do not
start the engine).
2. Fully depress the accelerator pedal slowly three
times within 10 seconds.
3. Turn the ignition switch to the OFF/LOCK position.
NOTE: If the indicator message illuminates when you
start the vehicle, the oil change indicator system did not
reset. If necessary repeat this procedure.

Oct 01, 2009 | 2006 Jeep Grand Cherokee

1 Answer

99 cherokee laredo over heating


You can test the system by disconnecting the engine temp sensor that turns on the fan, the engine computer will go into failure mode and turn on the cooling fan, if the fan does not run check for voltage at the fan with a 12 volt test lite..

Sep 08, 2008 | 1999 Jeep Grand Cherokee

2 Answers

2000 Jeep Cherokee Air Conditioner


If compressor isn't kicking in, check the connector atop the a/c accumulator, beside the coolant recover tank, in the engine compartment. That connector is atop a black bottle, and the connector goes to the low pressure switch. These switches do fail, and you can jump a wire across the connector terminals to see if the compressor comes on (engine running). As this circuit provides part of the ground path from the compressor clutch, if the switch is open, the compressor will never turn on. If the switch is failed, it can be replaced without opening the a/c system. Just disconnect the connector, unscrew the switch, replace it, and reconnect the connector.

Jul 22, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...