Question about Cars & Trucks

1 Answer

Hit button for remote start -- starts for 1 sec, shuts off. cycles twice more then nothing

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 39 Answers

Is the tach wire connected? or is it tach sensing? if its tach sensing, its not picking up the voltage increase when the car is running.

Posted on Nov 14, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 62 Answers

SOURCE: Turn the tv on, 1-2sec's l8r it turns off

sounds like the TV has a damaged power supply, most like caused by a bad capacitor on the power board, the capacitor exploded and leaked all the gases which stores electricity, so the power board isn't getting enough flow of electricity for the tv to stay on, very easy fix if you know what to do and have good soldering skills.

Posted on May 10, 2009

  • 1 Answer

SOURCE: wont start with remote.light blink one than two

disconnect battery to reset remote starter





Posted on May 13, 2009

  • 56 Answers

SOURCE: I have 05 300M the

Once is to lock and unlock the car some of the newer cars have it like that so you can do everything from the remote

Posted on Apr 14, 2011

  • 82 Answers

SOURCE: I have a 1999 chevy

check the battery has got plenty of voltage when you try to start it.if its low you may just need a new battery.

Posted on Jun 22, 2011

  • 209 Answers

SOURCE: PASSLOCK 1 STARTS FOR 2 SEC. SHUTS DOWN CHANGED

believe it or not, I have heard the instrument cluster to cause problems like this in similar vehicles. Obviously the anti-theft system is actuated. I don't know where the anti-theft module is for sure, but I did have an achieva which changing the cluster solved this same problem.

Posted on Sep 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have problem with remote control, my remote control gives me blue light to switch the dashboard on but there is no lights coming on the dashboard. what is the problem


Hi, your remote has probably lost its coding. If you have the owners manual check page 65 learning additional remotes. If not do the following 1. Plug in the 6 pin hopped coded plug to control unit under drivers seat. 2. Press unlock button twice to disarm. 3. Press learn button on hopped coded plug. this erases all pre learnt codes. The led on dash should start blinking once per sec. 4. Press learn button on hopped coded plug again. The led on dash remains on for 4 sec. and then starts blinking faster. Ensure to do step 5 within 25 sec. 5. Press any button thrice on your remote that has a problem. 6. In response led on dash remains on for 4 sec and then blinks once per sec.This indicates that the remote has been learnt. Hope this helps.

Mar 09, 2015 | 2006 Tata Indica LSi

1 Answer

Programming keyless entry to 95 landcruiser


1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.

5. Within 3 seconds the power door locks should cycle automatically indicating successful
entry into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
B. Immediately after letting go of the lock and unlock buttons, press the lock button by
itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle once
indicating successful programming. If the door locks do not cycle, or cycle twice.
repeat steps A and B in step 6 as your remote has not been accepted.
C. Repeat steps A and B in step 6 for each new remote.

7. Close drivers door.

Oct 29, 2013 | 2008 Toyota Land Cruiser

1 Answer

Having trouble with keyless remote control on 1993 lexus es300. Replace battery on remote- still not openning doors. Help Please!


Try reporgraming it

1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.

5. Press any button on remote for a minimum of 1 second.
System should now lock and unlock doors once.

6. Close and open drivers door.

7. Press any button on remote for a minimum of 1 second. System should now lock and
unlock doors. Once to confirm programming, twice to indicate programming failed.

8. Repeat steps 5, 6 and 7 for additional remotes.

Jan 02, 2013 | Cars & Trucks

1 Answer

Remote control has stopped working. Have tried changing the battery of the remote control but that did not work.


Does the red light on the remote light up when you push any of the button
if no, replace remote
if yes, then try repograming the remote to the car again.
-Have remotes' ready. if you have two then fob#1 and fob#2 (doesn't matter which one is #1 or #2)
-each step has to be done within 5 sec or it will not work, but don't do it super fast.
1.turn key just to the "on" position (not starting) and push "lock button " on fob#1 once and release
2.turn key off
3.turn key just to the "on" position (not starting)and push "lock button " on fob#1 once and release
4.turn key off
5.turn key just to the "on" position (not starting)and push "lock button " on fob#1 once and release
6turn key off
7.turn key just to the "on" position (not starting) and push "lock button " on fob#1 twice (if you only have one fob, then stop here and go to step 8)and push the "lock button" on fob#2 twice.
8.turn key off and remove key from ignition.
if you did it right, remotes' should work again.
good luck

Dec 17, 2010 | 2003 Honda Accord

2 Answers

Both key fobs for honda pilot 2006 no longer works. Do I need new keys or is it something internal such as a fuse?


First thing, does the red light on the remote light up when you push any of the button
if no, then replace battery inside remote
if yes, then try repograming the remote to the car again.
-Have both remote ready. fob#1 and fob#2 (doesn't matter which one is #1 or #2)
-each step has to be done within 5 sec or it will not work, but don't do it super fast.
1.turn key just to the "on" position (not starting) and push "lock button " on fob#1 once and release
2.turn key off
3.turn key just to the "on" position (not starting)and push "lock button " on fob#1 once and release
4.turn key off
5.turn key just to the "on" position (not starting)and push "lock button " on fob#1 once and release
6turn key off
7.turn key just to the "on" position (not starting) and push "lock button " on fob#1 twice (if you only have one fob, then stop here and go to step 7)and push the "lock button" on fob#2 twice.
8.turn key off and remove key from ignition.
if you did it right, remotes should work again.
good luck

Dec 17, 2010 | Honda Pilot Cars & Trucks

1 Answer

2000 Celica GT - I can get into the programming mode just fine, but I have tried to program THREE separate remotes and none of them will program. They are used, so I am "rewriting" them, but they never...


I saw this on one of the toyota forums;
1) Getting a Replacement Remote

Look on ebay or google, make sure the remote has the following FCC-ID: bab237131-056

2) Installing the remote (credit to iPal)

1 open door, take key out...

2 insert and remove key from ignition 2 times

3 close and open driver's door 2 times

4 insert and remove key from ignition

5 close and open driver's door 2 times

6 insert key into ignition

7 close door

8 turn ignition from 'lock' to 'on' and back to 'lock'

if you do step #8

*1 time it's for add mode

*2 times for rewrite mode

*3 times for confirmation mode

*4 times for prohibition mode

9 remove key

10 then door lock will cycle 'lock' and 'unlock' a number of times
corresponding to your key cycles in step #8

11 press lock and unlock button together for 1 ~ 1.5 sec then release

12 then within 3 sec press lock button for 1 sec then release

13 if you did correctly door lock will cycle once...

if wrong, twice... then do it over...

Jan 27, 2010 | 2002 Toyota Celica

2 Answers

HOW TO PROGRAM 2003 TOYOTA CAMRY FACTORY REMOTES


1. Driver door open and unlocked. Key out of the ignition
2. Insert the key and remove 2 times in 5 sec.
3. Close and open driver door 2 times in 40 sec.
4. Insert the key and remove it again from ignition.
5. Close and open driver door 2 times in 40 sec.
6. Insert the key in ignition,
7. Close the door,
8. Turn to on and back to lock in 1 second intervals. 1 time for add, 2 times for rewrite, 3 for confirmation 5 for prohibition. (yes, there is no “4”)
9. Remove the key
10. Power lock will cycle to confirm
11. For add or rewrite mode within 40 sec of the confirmation,
A. press “lock” and “unlock” buttons of the FOB at the same time between 1 and 1.5 seconds.
B. within 3 sec press “Lock” button for more than 1 sec and release.
C. If it’s correct, the power door lock will cycle once. If it’s wrong the door lock will cycle twice.

Sep 17, 2009 | 2003 Toyota Camry

4 Answers

2007 Volvo S80 V8 Sedan Service reset light


Install remote/key into socket.  Push and hold trip button on instrument cluster with all doors shut.  Push start button one time for key position one while holding trip button and count to five.  keep holding trip button and hit start button to key position two where all the warning lites come on the instrument cluster while still holding trip button.  Count to around ten and triangular warning lite should flash. Release button and remove key and then start engine.  May take a few attempts to reset this lite.  

Mar 30, 2009 | 2007 Volvo S80 V8 Sedan

2 Answers

Remote start


first make sure you have the keyless start entry setup. if u do then you need to lock the door with the transmitter after you lock the door press the start button and hold it down until it starts. It usually takes three or four seconds.

Mar 16, 2009 | 2005 Pontiac G6

2 Answers

CHECK ENGINE LIGHT


Any time the Service Engine light comes on the remote start is disabled for the engines safety. As far as the SES light, your dealer should be able to help you with the diag.

Nov 17, 2008 | 2008 Chevrolet Hhr

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...