Question about 2006 Ford F-150

2 Answers

I have an 06 f150 5.4 that cranks but wont start. Ive got fuel but no spark on any cylinders. I cranked it and the RPM's dont move. Could this be the crank sensor and if so where would it be l

5.4

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Maybe,,, it down around the harmonic balancer,, also look at the coil pack,,, see if the is any voltage

Posted on Nov 10, 2014

  • chuck urgitus
    chuck urgitus Nov 12, 2014

    I've changed the crank sensor and still no spark on any COP

×

Ad

Check for OBD Codes first

Then check for a failed battery

Look at module voltage next

Do not remove battery cables or all your data is gone

If you got injector pulse, you should have spark also

Check fuses

Posted on Nov 10, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 393 Answers

SOURCE: 1999 F 250 crank but wont start

look on injector pump make sure there are no loose wires

Posted on Dec 09, 2008

  • 491 Answers

SOURCE: no spark 1991 ford f-150 5.0 EFI

check your eec wires on driver side under hood for shorts

Posted on Jun 06, 2009

  • 1 Answer

SOURCE: Have a 2003 Taurus, 3.0 engine that has a misfire

did you check the injector pulse on that cylinder and it also could be the pcm , i had a taurus and a sable with good coils stop firing 2 cylinders and it was the pcm ,the code it gave was secondary coil but changed the pcm and it worked fine

Posted on Aug 29, 2009

sulavaca
  • 1007 Answers

SOURCE: my 1996 F450 7.3 diesel engine crank over but won't start, I have change the cam sensor, but still doesn't start

First, check the condition and operation of the following:

1) Spark plugs, leads and coil(s)
2) Air filter
3) Fuel filter and pump operation.

Posted on Nov 18, 2012

ginko
  • 19396 Answers

SOURCE: 2003 ford Taurus DHOC 3.0

Hi.

The PCM is located in the rear right corner of the engine compartment, sticking to the firewall:

ginko_304.gif
The PCM can be replaced with a new or used god-working one. In both cases the PCM must be reprogrammed using a Tech 2 tool that costs about $3000. The operation is done at the garage.

The PCM is unlikely causing misfire on a single cylinder. Check wires going to spark plugs. If the coil is getting no 12V on the ignition side check ignition. It is strange that one coil has no power, the engine usually does not start when that happens because the same coil gives power to spark plugs on different cylinders.

Check if there is a capacitor fixed to the head aside the coil (there should be one). It should be cylindrical and one inch long, held by a single screw and located aside the coil. If there is a capacitor, that must be replaced with the coil. If you have not replaced the capacitor that is probably involved in the problem.

If you have already replaced crankshaft position sensor, check crankshaft position sensor harness in PCM. I uploaded here the bulletin with CKPS to PCM testing:2003 Taurus CKPK PCM testing.

Test the PCM and CKPS connectors. Check again voltage to coils and spark plug cables. I understood that spark plug cable nr.3 has no spark from coil. Check DC in from ignition to coil.

Posted on Sep 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 grand prix 3.8 non supercharged.I replaced th head/intake gaskets..plugs/wires..etc. now it cranks but won't start. I used an inline spark testlight(I dont have a helper so I connected it...


Diagnose the no spark first. Check to make sure the crankshaft position sensor is not damaged and is plugged in. Check to make sure the camshaft sensor is also plugged in . Does the car have a RPM gauge? If so, check to see if the needle moves while cranking the engine, this would indicate the crank signal is good. Also, check to make sure the ground wires got attached under the ignition module bracket. The short burst of fuel is not uncommon on an engine that is not running.

Feb 22, 2015 | 2000 Pontiac Grand Prix

2 Answers

How to check a ignition coil pack to see if its good,


the coil does not crank the engine , the starter does that, sorry.
(if you ever had to hand or foot crank and engine , youd under stand that. (like motor cycles or boat engines, or per 30s cars.)

in fact will crank all day with no spark parts on car..

x2, the scan tool does tell you why there is NO STARTS, CRANKS OK. The pcm can detect, one missfire in 10 cmp;ckp signals.
  • CRANK FOR 5 SECONDS
  • release, key
  • scan tool has DTC errors?, read the believe them.
no engine stated of 4 or more,

U checked everything but spark,
why, check spark at all cylinders, all most fire or the engine will not run or stall.
That test be first, if not starting (AFTER SCAN TEST)

IF NO spark fuses are next , not last.
lets do no start fails tests. (cranks perfectly 200 to 300 rpm)
  1. : check fuses
  2. key on, CEL lamp must glow, if not , ECU fuse blown.
  3. crank with scan tool , see P03xx DTC errors, see RPM dead.?
  4. check for spark? got spark x4 or times number of cylinders?
  5. got spark try test fuel now, runs for 3 seconds?
  6. yes, runs on test fuel now means lost fueling
  7. no, dont run on test fuel, means, 1 to 5 done wrong above or engine compression bad.
  8. bad fueling, huge number of tests. check fuel pressure now.
confused, try a shop and watch them, learn.

Jan 12, 2015 | 2005 Suzuki Forenza

1 Answer

I have an 06 f150 5.4 that cranks but wont start. Ive got fuel but no spark on any cylinders. I cranked it and the RPM's dont move. Could this be the crank sensor and if so where would it be l


run the fault codes to check which sensor is switched off. It could be a crank position sensor but it could also be a cam shaft position sensor or immobiliser that is non operational.

Nov 09, 2014 | 2006 Ford F-150

1 Answer

Low voltage


does it crank fast, at 250 spec RPM?
no year, no joy, all cars have a year,
and and engine option (displacement size???)
my wild guess, is it wont crank or cranks dead slow.
right?
and the battery is DISCHARGED. right,
use jumper start cables. start now?
that be first.

wont crank
cranks perfectly but wont start ?(check for spark, x number of cyl)
spark good, try test fuel
test fuel works for 3seconds and stalls,. then fueling problem , ask.

Jan 21, 2014 | Suzuki Grand Vitara Cars & Trucks

1 Answer

Ok guys I have a 97 lhs the fuel pump went bad replaced it car ran great again but now it wont start turns over have replaced the fuel filter and the coil pack and still it wont start im stumped please...


this is not unique to chrysler, at all, its EFI.
all EFI works alike , the shapes change to fool the non tech.

i dont know about you, but in my shop
i check fuel pressure and you found it at zero
then put in a new pump and didnt check pressure.
why would you do that? after all it was zero.
and you do that and its still zero. then find a bad wire /connector
in the fuel pump power feed or the fuel pump relay.
or ? a inertial cut out sw, or rollover switch. (i said generic)
now rule 2: if spark is bad, the ECU cuts fuel,
BY DESIGN. that dont mean spark really is bad, but does mean
the ECU can not SEE spark, or that the Tachmeter line is dead.
All ECU monitor spark 1 way or the other, and if that fails.
there WILL BE NO INJECTION period.
use your scan too to see DTCs while cranking and dead RPM cranking for 5 seconds, release key and look for crank or cam
sensors errors, key key on for 1min to see them pop up.

your are stumped because you are not troubleshooting, only guessing. and will make you broke fast.
here at the simple tests, in the proper order.
1: compression on all cylinders. if all are horrid.
the cam timing is way off. no motor will run like this.
2: spark check for spark. ! at all spark plugs, not just one.
3: make sure the ECU is happy about spark, RPM moves cranking , etc.
if spark tips are dry at this moment test fuel can be used.
does it start now then stall as the the test fuel is consumed.?
4: check for injection.
do the injectors click , do all of then click , cranking>?
if all fail, i can assure you the ECU is CUTTING FUEL!!!
if one dont click , then run a NOID lamp test in this injector
and make sure the coil reads near 10 ohms not infinity.
5b: you can do an injector balance test.
cranking, see that the pressure drops, as you crank.
Ill not cover this , as its a SOP proc, in all EFI books published.
but take to bank, can witness the drop in pressure and know the injector does in fact inject.
that way or by looking at fuel soaked spark tips.

the injectors can fail in many a way, they are fuel cooled.
A:shorted coil, open coil
B: ecu driver dead.
C: injector clogged or leaking (leaking causes flooding)
the injector has inside 10 micron screens. tiny,
d: bad fuel. cant burn or clog s screens.

you are now totally confused (above) or are un-stumped.

if you dont understand EFI at all , then lets go back to 1920.
this works too, on all otto cycle engines
1: compression, good, time number of cyclinders.
at spec. all equal, most 150psi to 200 is typical today.
2: got spark times all cycliners.(oh, yes, timing right)
3: over fueling or under.?

that is it, its and air pump , if it can pump air, it's hopeless.

the 3 steps work , every time. the tests are easy and are documented for 90 years, now.

Oct 02, 2013 | 1997 Chrysler LHS

1 Answer

92 wrangler wont start


Jiggle the wire connectors going in to the computer under the hood -- first check battery cables/terminal connections at battery -- beleive it or not, connection could SEEM good because you get crank & lights, but if it's faulty, loose, engine won't start - computer requires good solid voltage flow.. next check a fusible link very close to the battery off of the positive cable. check fusible link carefully. this could cause your problem for sure.

Aug 10, 2012 | Jeep Cars & Trucks

1 Answer

My 2000 clk 320 wont start it cranks but wont fire, The fuel pump is not coming on the relay is good. the cps is putting out a little over 1vac. I checked the voltage at the cpu connector e pin 37 &...


The only thing that will shut the fuel and the spark - is crank position sensor. And they do go bad on MB.
If you have scaner which can read data from the engine , you can monitor the rpm while you crank the engine , if you see 0 rpm while cranking , CP sensor caput.

Jun 03, 2010 | 2000 Mercedes-Benz CLK

1 Answer

Engine cranks but wont start


Usually if no rpm signal, the vehicle won't start. Engine cranking, did you check for spark at the spark plugs? The fuel pressure you listed may have been the initial prime. It sounds like no injector pulse. The rpm signal comes from crank sensor. If your missing rpm signal, may thought is the crank sensor.
Were there any applicable trouble codes?

Apr 06, 2017 | 2001 Ford F150 Styleside SuperCrew

2 Answers

1997 gmc savana 4.3, wont start ,has new fuel pump, new pressure regulator, new spark plugs , i cleand up the maxi ijector, looks ok no leaks,i do have spark and fuel but still wont work any ideas


only 3 things will cause this engine not to start (crank and not start) fuel, ignition, timing.
You haven't mentioned the engine cranks over or not, so I have to assume it cranks over.
Possible timing chain or the crank sensor on the timing chain. Have you checked this? you need to remove number 1 spark plug & when the piston is in the full top position on compression, remove the dist cap & see what spark plug wire the rotor is pointing to inside the dist cap. (I'm sure if you google checking for top dead center you'll find the proper procedure)

Oct 12, 2009 | GMC G3500 Cars & Trucks

Not finding what you are looking for?
2006 Ford F-150 Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...