Question about Mazda B2300

1 Answer

2001 mazda b2300 rebuilt motor and have replaced all internal parts. now truck wont crank theft light flashing

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mazda Master
  • 42,190 Answers

You may have to use a scanner to reset the immobiliser as when the battery is off for some time the CPU program becomes corrupted and has to be reset.

Posted on Nov 10, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75822 Answers

SOURCE: 2000 Windstar rebuilt engine won't crank theft light comes on

Refer to the owners manual for dis-arming procedure for the anti-theft, if you do not have the owners manual here is a link to Ford for a free PDF file of the owners manual.

http://www.motorcraftservice.com/pubs/content/~WOYWIN/~MUS~LEN/41/00winog1e.pdf

Posted on Oct 13, 2008

  • 3 Answers

SOURCE: 2001 ford taurus wont start and anti-theft light is blinking

Either you may be using a key that you had copied from the original or your chip went bad in your original key. Most of cars now a days have the key censor in the key so if it is the incorrect key it will not start your car or if it does not read that chip it will not start

Posted on Feb 05, 2009

  • 750 Answers

SOURCE: my hold light is flashing in my 2001 mazda millenia

hold light flashing means you have a transmission fault of some kind, check vehicle speed sensor

Posted on Jul 03, 2009

  • 708 Answers

SOURCE: MY 2000 FORD EXPIDITION IS FLASHING THE THEFT

my 2000 did that and I had to disconnect the battery for 30 minutes and everything reset and I was able to go again.

Posted on Jul 06, 2009

ajarema
  • 404 Answers

SOURCE: what is check engine code p1443 on a MAZDA 1996

Diagnostic Trouble Code (DTC) P1443 indicates a failure in the EVAP canister purge valve circuit. The Evaporative Emissions (EVAP) Canister Purge (CP) valve controls the flow of vapors from the fuel vapor storage canister to the intake manifold during various engine operating modes. It may need nothing more than a good cleaning, vacuum hose connected or that is leaking, or may need more. I suggest you seek out the services of a good mechanic. Do not just throw parts at this. The code does not mean that any part needs replacing. It just means the EVAP system is being effected.

Posted on Apr 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I just change the upper ball joint on 2001 Mazda b2300


Old, Some times the hole control arm assembly is changed, if you can find it priced reasonably other wise yes, with proper tools the ball joint can be changed. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How to Replace Ball Joints on Ford Ranger
Replacing Ford ranger ball joints
2003 Ford Ranger Ball joint and Control Arm Repair Part 1 Lower Ball Joint
Mazda B2300 Ball Joints eBay


May 19, 2016 | Mazda Cars & Trucks

1 Answer

Have a 95 Mazda B2300 2.3L motor.. Won't crank but dash lights come on


check battery voltage as lights take little voltage/amperage than a starter. then check voltages at starter connections on all wire terminals and ground of starter. if good then the starter is bad.

Aug 11, 2015 | Mazda Cars & Trucks

1 Answer

What can i do to get my 2001 F150 XLT 4.6l TO START. THE anti-theft light keeps flashing and wont allow thwe truck to start.


Best to check out Web photos for the Inertia switch which has a reset button on it. This safety device is suppose to cut power to your fuel pump when the truck is bumped in an accident. It is a no cost fix. The part is usually around the floor kickpanels.

Nov 08, 2014 | Ford F-150 Cars & Trucks

2 Answers

Anti theft light blinking,dash lights up,windows roll up and down but car wont start. How do I start it?


If the anti theft light is blinking and you say that everything else fine.. My first thought is that the key is not programmed to the vehicle. The key has a internal chip that must be programmed to vehicle in order to start. Now my other question is, Is the key your using for the vehicle the original key or have you just recently had a key made? Regardless, in order for the yur Tribute to start, the key. Or keys have to be program to vehicle by your neighbor dealership. Thats the reason for your anti theft light is blinking

Oct 09, 2014 | 2001 Mazda Tribute

1 Answer

2004 Mazda B2300 no spark after engine overhaul.


An anti theft light light is trying to tell you something. That thing is that the system will not allow the engine to start. Most systems shut off fuel and or ignition. Check and see if you have ground switching on and off for the injectors. If the anti theft system is shutting off the ignition then it will also shut off injectors/fuel system. Figure out the antitheft FIRST or you are probably going to chase you tail.

Dec 10, 2013 | Mazda B2300 Cars & Trucks

1 Answer

2001 Mazda B2300 engine repair and compatibility


If you threw a rod,This would be a total engine rebuild.(Cost vary by location)
You can use the Ranger motor ,but you will need to swap most of the accessories from the Mazda motor so the wiring harnesses match up.


Please rate this a fixya

Feb 09, 2009 | 2007 Mazda B2300

1 Answer

Od light flashing


yes that is your OVER DRIVE light do you have it in OVER DRIVE or regular "D" for drive is it shifting okay?????maybe see garage who replaced your transmission maybe something not plugged in proper! hope this helped you.John

Jan 11, 2009 | 2001 Mazda Protege

1 Answer

2000 Windstar rebuilt engine won't crank theft light comes on


Refer to the owners manual for dis-arming procedure for the anti-theft, if you do not have the owners manual here is a link to Ford for a free PDF file of the owners manual.

http://www.motorcraftservice.com/pubs/content/~WOYWIN/~MUS~LEN/41/00winog1e.pdf

Sep 10, 2008 | 2000 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...