Question about 1995 Lincoln Mark VIII

1 Answer

<!-- from fixya rte -->Where is the fan speed control resistor - 1995 Lincoln Mark VIII

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lincoln Master
  • 14,362 Answers

Next to the blower motor.it's the resistor

Posted on Nov 10, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you know if your blower resistor is bad?


Unlikely a blower motor resistor problem. If the resistor is faulty. the fan speeds will not work/fail on the lower speeds. High speed will normally always work. If the fan is non operational suspect a fan motor issue.Bad fan motor/switch/wiring to it

Jul 22, 2015 | Cars & Trucks

1 Answer

How to trouble shoot front blower


There are several reasons for a blower to stop working. Does it work on ANY speed? Does the AC compressor lamp or any of the vent control LEDs still work when using the AC controls? Do ANY of the speed for the blower work or are they all dead?

1st, you wanna check your fuses. There will be fuses in the underhood fusebox marked blower or heater fan, check and repalce as necessary. Also, if the earlier check for working LED bulbs on the AC control panel showed some or all lights dont ever turn on when engine is running, you may have problems with the control system.
if the fuses are good, now you need to test parts. there is a blower motor speed control aka blower resistor that frequently fails on most cars. It is the part that carries the current for all speeds of the blower and regulates speed when commanded. It has to absorb the excess energy to lower speeds and it tends to get very hot and burn out as a result. If it has failed, there will be power IN on one of its wires, and no power OUT on any others. If you have no multimeter or testlight to check things like this, Id recommend taking it to a certified mechanic.
If the control lamps all work that means controls have power, if the blower resistor has no power, fuses or blower relay are the most likely cause. if the blower resistor has power but still no fan, most likely your fan has failed. as a general rule, I replace fans and blower resistors as pairs. fans tend to last longer, but they also get more demanding with age (kinda like people) and that extra demand will burn out the newer resistor much faster than when the fan was newer. it can be alot of time and money to change a blower TWICE, so to be sure it wont fail again, test current, or simply replace the blower fan if it is determined a resistor has failed. (a good fan in theory shouldnt draw enough amperage to burn out a good resistor, EVER, so if the resistor burns, the fan is typically drawing too much power, and even though it works "fine", it will burn the next resistor in a short time as well.).

Feb 24, 2015 | 2005 Dodge Caravan

1 Answer

Fan speed controller replace


the fan speed is controlled by a resistor pack located in the fan housing. They are subject to burning out . the problem is not always in the switch as each setting of the switch activates a resistor which controls the amount of current the fan motor gets

Jun 24, 2013 | Renault Cars & Trucks

1 Answer

A/c blower stop working all speeds, check have power, ground out speed sensor and fan comes on, replaced speed sensor, now fan just works on high when wiggling fan switch, I replaced fan switch, now...


Depending on the year and model, you should have a resistor that controls fan speed. Not sure what a speed sensor is.
On most import cars, the speed is controlled by the ground circuit. If you have power and the fan will run if you ground it, check the fan switch again and the resistor. Then look at the ground for the switch.

Jul 17, 2012 | Hyundai Santa Fe Cars & Trucks

2 Answers

01 grand.prix ac fan switch only works on high. has a duel temp controller when you turn fan off the only way fan comes back on is to move the temp controller levers


Hi!!
When the Blower Motor Resistor (controls blower speeds) goes bad, the blower motor works only on HIGH SPEED. REPLACE IT.
BLOWER MOTOR RESISTOR Removal & Installation
  • Disconnect negative battery cable.
  • Remove right lower instrument panel insulator panel.
  • Disconnect blower resistor connector located behind right side of dash.
  • Remove blower resistor screws and blower resistor.
To install, reverse removal procedure
Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa!!

Feb 18, 2011 | 2001 Pontiac Grand Prix

1 Answer

Replace fan speed switch


Before you replace the fan speed switch...make sure you check the fuse...then check the motor...and finally check the resistor assembly...the resistor assembly controls the different speeds of the fan motor by allowing the switch to put different resistors in and out of the circuit to reduce the fan speed...it is usually located on the heater housing near the fan motor..they are a common failure...the switches don't fail as often

Jan 20, 2011 | 2002 Pontiac Sunfire

2 Answers

2002 Honda Odyssey fan only works at high speed. The A/C compress


Usually when the blower fan only operates on hi speed, its because of a failed blower motor resistor. You still have hi speed because on hi, the power going to the blower motor goes directly to it, as opposed to the lower speeds, when the power is routed through the resistor, thus lowering the voltage, which in turn lowers the speed of the fan. The resistor is usually located near the blower motor itself, under the hood back near the firewall.

Aug 15, 2009 | 2002 Honda Odyssey

1 Answer

Fan works on high only


Check your blower motor fan speed control switch. They go bad frequently. You could have checked the resistor by jumping the wires to the different terminals to be sure the resistor was good. That pretty much just leaves you will the fan speed control switch. Good luck.

Feb 24, 2009 | 1986 Chevrolet Corvette

Not finding what you are looking for?
1995 Lincoln Mark VIII Logo

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

fordexpert

Level 3 Expert

5520 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...