Question about Ford Escape

1 Answer

I have a Ford xscape the remote start will be allowed once lock the doors like it's going to start then just beeps 3 times loud it used to chirp but now they're loud beeps

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 37 Answers

Possible horn burnt out. The three chirps means a door or hood is open

Posted on Nov 10, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
eitan
  • 291 Answers

SOURCE: door lock problem

Even though it's a 2001, it's still an A3, so the locks are operated using a separate vacuum pump, and hard plastic lines. Check inside the drivers door hinge area. Remove that accordion thing over the wires. There's a vacuum coupling centrally located after you twist, and separate the lock on the harness connector, and separate the 2 parts. There is also, a little tiny "o"-ring that seals the vacuum passage. Replace it, and see if the wait is shorter. I highly recommend using a little Vaseline to aid in the insertion , and seal of the new o-ring. Good luck.

Posted on May 15, 2008

  • 1 Answer

SOURCE: remote horn beep

Did you check with the other remote? If you have the same pb, I would say the alarm control box is not working properly anymore.Or the control lost its programation.

Posted on Jun 20, 2008

  • 35 Answers

SOURCE: 2005 Hyundia Elantra alarm goes off for no real reason

When a battery starts to go bad it will set the alarm off constantly. Check the date on your battery and if it's between 3 and 4 years old most likely this is the cause. I had it happen before.

Posted on Jan 02, 2009

  • 77 Answers

SOURCE: rear doors on my 2003 Ford Expedition won't lock/unlock

check if it will work with the child locks engaged/disengaged if nothing the lock actuators may be worn out.

Posted on Aug 01, 2009

  • 170 Answers

SOURCE: 2007 Saturn Aura; when trying remote start horn

press the lock button on the remote then press the remote start button. if this does not work check remote start status using steering wheel buttons

Posted on Jan 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to stop beep when locking and unlocking camry le 2010


When Horn chirp is enabled, the vehicle horn will chirp on locking and unlocking the vehicle, to enable or disable the horn chirp:

1. Turn headlight switch "OFF"

2. Cycle the ignition switch from "LOCK" to "ON" three times (within 5 seconds) leaving it "ON"

3. The vehicle security indicator will illuminate continuously for 5 seconds

4. During the time the indicator is illuminated, operate the horn(for 1 second). The turn signals will flash once to confirm successful programming.

5. Turn ignition switch to "LOCK" and test system with the remote controls.

To disable horn chirp, repeat the procedure for enabling.

The user manual actually declares customizations of the smartkey must be done by the dealers using special equipment. However, the above procedure works on a variety of years and models. And I see no where in the user manual that refers to the horn and door lock even being a customizable setting.

Aug 10, 2017 | Cars & Trucks

1 Answer

Where is the Ford 2010 Ford Explorer "Remote Keyless Entry (RKE) module" located


The RKE is controlled by the SJB - smart junction box ! Fords BCM - body control module .
Principles of Operation
Power Locks
The SJB controls the power lock/unlock feature of all of the vehicle doors, including the liftgate, to lock or unlock based on the input received from the door lock control switch, the keyless entry keypad or the remote keyless entry (RKE) transmitter. Power locking and unlocking of the doors function independently of the key position, vehicle speed or transmission position. The smart junction box (SJB) activates internal relays to supply the correct voltage and grounds for the door lock actuators.

Your best bet would be to take to ford dealer or some other qualified repair shop .
Remote Keyless Entry (RKE) Transmitter Lock/Unlock Control - Unlock
The RKE transmitter feature provides lock/unlock functions independently of key position, vehicle speed, or transmission position. The RKE transmitter feature provides a 2-step process for unlocking the doors. Upon receipt of the first request for unlocking the doors, the RKE control feature requests the SJB to unlock the driver door only. If another unlock request is received within 3 seconds of the first, the RKE transmitter feature requests the SJB to unlock all the doors. This feature can be changed to global unlock, so that all the doors unlock on the first press of the unlock button. To toggle between the 2-step unlock and the global unlock press the lock and the unlock button on the RKE transmitter at the same time and hold the buttons for 4 seconds. The turn signal lamps flash to confirm that the feature has been toggled.
Remote Keyless Entry (RKE) Transmitter Lock/Unlock Control - Lock
The RKE transmitter feature requests that all the doors be locked when the lock button is pressed. On any press of the lock button with all doors closed, the SJB provides 1 flash of the parking lamps. If any door is ajar, no flash occurs. As soon as the last door is closed, the SJB provides the flash of the parking lamps. If 2 presses of the lock button are received within 3 seconds, the horn chirps once, and the parking lamps flash twice to indicate that all the doors are closed and locked. If any door is ajar when the second lock request is received within 3 seconds of the first, the RKE transmitter feature requests the SJB chirp the horn twice without flashing the parking lamps to indicate it locked all the doors but 1 or more doors are ajar. When the key is in the ON or START position, the parking lamp flashes and horn chirp confirmations do not occur.

All locks not working ?????
  • The doors do not lock/unlock using the remote keyless entry (RKE) transmitter
  • RKE transmitter battery
  • RKE transmitter
  • RKE transmitter programming
  • Aftermarket system
  • SJB
  • Go To Pinpoint Test H .

Apr 16, 2017 | Ford Cars & Trucks

1 Answer

My 2001 ford focus keeps locking. The power locks automatically lock as soon as I unlock them, barely enough time to open door.


Your Focus may be equipped with the autolock feature. Try this:

To deactivate/reactivate the autolock feature using the power door unlock control

You must complete steps 1-7 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds.

1. Turn the ignition key to ON.
2. Press the power door unlock control three times.
3. Turn the ignition key from ON to OFF.
4. Press the power door unlock control three times.
5. Turn the ignition back to ON. The horn will chirp.
6. Press the unlock control, then press the lock control.
The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated.
7. Turn the ignition to OFF. The horn will chirp once to confirm the procedure is complete.

Feb 18, 2015 | 2001 Ford Focus

1 Answer

My ford excape sounds the horn once loud and locks the doors like it's going to start then just beeps 3 times loud plz help


Try resetting your remote device by holding it near the front drivers side and press and hold the emergency button until the horn blows once. See if that does the trick.......

Nov 08, 2014 | Ford Escape Cars & Trucks

1 Answer

Factor disarm wire can not locate it? checked the drivers kick panel, door locks are not disaming the system from the door lock moduel


To turn off the auto locks 1 turn the key on 2 press the unlock button 3 times, 3 turn the key from on to off, 4 press the unlock button 3 times, 5 turn the key back to on and the horn will chirp, 6 press the unlock button, then the lock button. the horn will chirp once if the auto locks are deactivated, or twice one short and one long chirp if activated. 7 turn the key off and the horn will chirp once to confirm exiting the system

Apr 21, 2010 | 1998 Ford Expedition

1 Answer

I changed battery and now it dosnt work


You lost your program of the key module follow these instructions.

To Program a Remote for a VW
Put your good key in the ignition and turn to "ON", do not start the engine. Make sure all the remotes you want to use are present because they have to be programmed at the same time.
- Close the door and insert key #2 into the driver's side lock. Lock the door.
-Within 5 seconds of locking the door, press unlock 2 times on the new remote, key #2.
-(if this is remote #3, press unlock 3 times. if this is remote #4, press unlock 4 times).
-If there's a chirp or beep do not press it again. This means that the car has recognized the new keyless entry remote.
- Repeat with other remote or unlock the car and turn off - done.

Mar 23, 2010 | 1996 Jaguar Vanden Plas

2 Answers

Key remote wont work even with new batteries


The remote likely needs to be reprogramed. If you have both remotes you will need to take these to the dealer and have them reprogramed.

Jan 25, 2010 | 2000 Volkswagen Beetle

1 Answer

I bought a new Keyless remote for a 2007 Forester from a Subaru Dealer to replace an original one that went bad after 2 years. I have followed the directions in the owner's manual to program it, but can't...


IMPREZA: 2005, 2006, 2007 and
FORESTER: 2005, 2006, 2007, 2008
Check for Immobilizer key on Forester XT models only.
information is always subject to change and correction imp05keylessremote1.jpg
new remote for 2005 Imprezas.
This is not the same remote as the 05 Legacy/Outback remote which also has truck/gate release on the front and a red panic button on the back.
Lock: press Lock button for 2 seconds or so to lock car, and arm optional security system. The car with chirp once and turn signals flash for locked, 5 short chirps and signal flashes if any door is not fully closed. The dome light goes on for 15 seconds and ignition key ring (if present) will light for 30 seconds when unlocked.
Unlock: press unlock one time for driver's door, press again within 5 seconds to unlock all doors inkling rear gate (wagon). The system does not open the trunk.
Panic mode: press and hold lock button for approx. 3-4 seconds to activate Panic mode. I panic model the horn honks and turn signals flash until either the lock or unlock button is pushed again.
Finder mode: Press lock button 3 times within 5 seconds to activate Vehicle Finder mode. The horn will honk once and the turn signals will flash 3 times
Distance: works within approx. 30 feet depending on battery strength, nearby concrete walls and etc.
Audible Chirp On-Off: the system will chirp when locked or unlocked. To turn OFF the chirps, unlock the door and then push both lock and unlock buttons at the exact same time for 2+ seconds. There will be 2 chirps indicating the the audible is off. To turn the chirp back on, repeat the process and the system will chirp one time when it is back on.
Battery: as the battery ages it will only work as you get closer to the car. When a battery is replaced, the transmitter must be re-synchronized with the Keyless control unit. To synchronize, press the lock or unlock button 6 times.
Programming: 4 codes may be programmed.
Sit in driver's seat and unlock all doors. Open and close the driver's door
Turn the ignition key from LOCK to ON position 10 times within 15 seconds. Be sure to stop at both lock and on. The horn will HONK once to indicate transmitter programming mode is activated. Leave key in LOCK position and don't remove it from ignition.
You now have 45 seconds to complete the programming as below.
Open and close driver's door again.
Push either lock or unlock button on the remote you want to program. The horn will honk 2 times when successful.
To continue and program other remotes at the same time: open and close the driver's door and push lock or unlock on the remote. The driver's door must be opened and closed between each remote you want to program.
Done programming? remove the key from the ignition and the horn will honk 3 times.
DELETE old codes? Reprogram 4 times, it will overwrite old codes.
Alarm Security System: optional on all models. When locked there is one chirp (can be turned off, see above), the turn signals will flash and the red 'security' light will start to flash once every 2 seconds except for STi which flashes twice every 2 seconds.
There will be 5 chirps if a door, hood, and trunk or gate is not fully closed
You can also arm the system by using the power lock button on the driver or passenger door as you get out of the car and then closing the door behind you.
Disarm the system: push unlock for 2 seconds
Lost remote, alarm activated? When you can't use a remote to turn off the system: open the door with a key or try to start the car and the horn will start to honk. Turn the key on-off 3 times within 5 seconds and the alarm will go off and you can start the car. It's simple!
VALET mode: To set valet mode or just to disable the security alarm system: 1. unlock all doors 2. physically open the driver's door 3. hold the UNLOCK button on remote for 2+ seconds. The red 'security' light will then flash 2 times a second until the car is turned on.
System has been Tripped (except for STi): if you unlock the door with the remote and it chirps the signal light flash 4 times, the system has been triggered;
Identification mode: To find out what happened and why the system was triggered:
Open and drivers door, leave it open. Turn ignition key from LOCK to ON 2 times and then leave in LOCK position.
Tripped code: 1 security light flash: a door has been opened, 3 flashes when the impact sensor was triggered, 4 flashes when the ignition was messed with or battery disconnected

Nov 19, 2009 | 2007 Subaru Forester 2.5X L.L. Bean...

2 Answers

Auto Lock Activation


Deactivating/activating autolock
There are 3 methods to enable/disable this feature. One through your
dealer, the second with a power door unlock/lock sequence and the third
with the keypad.
Before following the activation or deactivation procedures, make sure
that the anti-theft system is not armed, ignition is off, and all vehicle
doors, liftgate and liftgate window are closed.
Controls and features
Power door unlock/lock
procedure
You must complete steps 1-5 within
30 seconds or the procedure will
have to be repeated. If the
procedure needs to be repeated,
you must wait 30 seconds.
1. Turn the ignition key to ON.
2. Press the power door unlock control three times.
3. Turn the ignition key from ON to OFF.
4. Press the power door unlock control three times.
5. Turn the ignition back to ON. The horn will chirp.
6. Press the unlock control, then press the lock control. The horn will
chirp once if autolock was deactivated or twice (one short and one long
chirp) if autolock was activated.
7. Turn the ignition to OFF. The horn will chirp once to confirm the
procedure is complete.
Keyless entry key pad procedure
1. Enter 5 digit entry code
2. Press and hold 7/8 control
3. Press and release 3/4 control
4. Release 7/8 control.
The user should receive a horn
chirp
to indicate the system has
been disabled or a chirp followed by
a honk to indicate the system has
been enabled.
Smart unlock
This feature prevents the driver’s door from locking while the key is in
the ignition. This feature will unlock only the driver’s door if the key is in
the ignition cylinder, the driver’s door is ajar and all doors are locked
using the interior trim switch. If these conditions are met, the entire
vehicle will lock and the driver’s door will unlock within 1 second.
Controls and features
127

May 15, 2009 | 2002 Ford Explorer

1 Answer

Auto door locking on Ford Mondeo


It sounds like it has been deactivated so we are going to reactivate the auto lock.

The numbers I will be saying will have to do with getting this to work so:
you will need to put the key in to the ignition switch.

1= is back to listen to the radio
2= is to get key out
3= is just before you start
4= is for starting your car

When we do this 1 and 4 will not be used
Do this and we will hope that it works like it should:

1: Turn the ignition with you key up to on( don't start)

2: Press the power door lock control 3 times

3: now turn the key back once (to off position)

4: Press the power door unlock control 3 times

5: ok turn the ignition back up 1 time. (The horn should chirp)

6: Then press the unlock control, then press the lock control, again (horn will chirp 1's) If auto lock
was activated.

7: Turn the ignition back 1's, Then the horn should chirp once to confirm the procedure was completed.
Nikki2913

Nov 23, 2008 | 2006 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5530 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...