Question about Cars & Trucks

1 Answer

How to remove back tire instructions - Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 5,433 Answers

Jack vehicle up and remove wheel nuts!

Posted on Nov 10, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instructions on removing master brake cycilinder


Open the hood. the master is on the drivers side. Remove the 2 brake lines. remove the 2 nuts holding it to the booster. Follow the instructions with the new master to bench bleed it, then install it. Then you need to bleed the entire system. Remove the tires and crack open the bleed valve, close it back. have some one pump and hold the brake pedal, release the valve, then close it. Do this three or four times to rid the system of air. Check the master after every tire and fill as necessary.

Oct 20, 2014 | 2003 Ford Windstar

1 Answer

Do i have to pull the rear half shafts to get the back tire off 2006 dodge 2500 HD


Best to obtain a work shop manual. not hard to do , manual gives instructions and explodes views.

Sep 21, 2014 | Cars & Trucks

1 Answer

Instructions on changing front brakes on a 1993 delta88 oldsmobile 1993


Instructions
    • 1Loosen the lugs nuts using the tire iron. Place the wood blocks in front of the tires you will not be removing.
    • 2 Raise the vehicle using the floor jack. Set the jack beneath the support strut that runs along the outer edge of the undercarriage. Raise it enough to allow the tires to clear the ground. Place the jack stands underneath the same strut as the jack.
    • 3 Remove the lugs nuts completely and take the tire off. Set these all aside.
    • 4 Remove the mounting bracket bolts with a socket wrench. The mounting bracket is the metal half-circle that is revealed when you remove the tire. Tie the mounting bracket to the undercarriage with rope to prevent stress damage to the brake line.
    • 5 Remove the brake pads from the bracket by hand.
    • 6 Compress the caliper cylinder with the C-clamp. The caliper cylinder is the 3- to 6-inch wide cylinder in the center of the bracket. Make sure that it is flush with the bracket.
    • 7 Install the new brake pads where the old ones were.
    • 8 Reattach the mounting bracket to the rotor. Reattach the tire and finger-tighten the lug nuts. Lower the vehicle and the tighten all of the nuts with the tire iron.

Apr 08, 2014 | 1989 Oldsmobile Delta 88

1 Answer

How to get storage retainer out of spare tire



Remove retainer? Does it unscrew? Oh, after lowering, eh?
Uh, yeah, should, easy. You right.

Nov 23, 2011 | 2001 Ford Windstar

1 Answer

How i remove the spera tire on mitsubishi montero


look in your owners manual it will have all the instructions how to access the jack usually the jack is mounted under the carpet in the back of the vehicle on the side remove it there should be a tag to show the instructions how to get it out

Dec 11, 2010 | 2001 Mitsubishi Montero Sport 4WD

1 Answer

How to change struts on 86 pontiac fiero


Jack up car.
Remove tires on back.
Remove Nut on top of each strut, located inside engine hatch.
Remove lower bolts from spindle.
Remove strut.
Use spring compressor to remove springs.
Reverse procedure to replace.

Apr 30, 2010 | 1986 Pontiac Fiero

1 Answer

Tire pressure monitoring system 2007 Chevy 2500HD


There is a Fuse that is labeled (hzd, or Hazard ) remove it for 15 sec. and return to position it should reset the whole system then check and see if it goes back to original operation good luck

Apr 03, 2010 | 2007 Chevrolet Silverado 2500HD

2 Answers

Change front rotors kia rondo 2007


Remove the tire, remove the brake calipers, 2 bolts on back side of rotor, remove the carter pin that retains the bolt position if equiped, remove the center nut. When you pull the rotor off watch for a set of bearings to drop out. To install the new rotor reverse the process.

Sep 17, 2009 | 2007 Kia Rondo LX V6

1 Answer

Where are the tools to remove the spare tire hidden?


they are either in a compartment on the tailgate or the right or left side trim panel in the back of the vehicle. instructions should be in tray with tools

Aug 23, 2009 | 1997 Lexus LX 450

1 Answer

Cant figure out how to remove the spare tire in this vehicle.


Couple of choices here....look for an access panel in the rear of the caro area on the side wall, it should remove...look there and there will be instructions. If not there, look for a little plastic square tab on the floor in the very back of your van, pop that up and it should look like a nut or something and you place the jack handle on that and spin down the spare from the underside.

Jul 12, 2009 | 1995 Plymouth Voyager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...