Question about 2000 Dodge Caravan

1 Answer

How do i reset my command start

Command start wont work after the battery cable was cleaned

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Dodge Master
  • 1,224 Answers

Disconnect battery five minutes
This is standard procedure to restart

Posted on Nov 10, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 monte carlo ss put key in attempt to start wont start leave in on position resets and then starts wipes out radio memory also


This sounds like a possible dead battery, or a highly corroded battery terminal or connection. Remove both cables from the battery - starting with the ground side first. Then either physically clean the battery and cable connectors, or try carefully washing them with a baking soda solution and an old brush.

Apr 28, 2016 | Cars & Trucks

1 Answer

2009 jeep commandeer wont start, when I turn the key there is no sound, lights wont turn on and is that wasn't enough the key gets stuck in the ignition. any ideas?


it wont crank, no A/t car starts unless cranked first. (a key point)

fix head lights first. this is a feature in all cars.

that is SIMPLE and HOT all the time

they must work at all times and is the top way to diagnose

electric problems



you have a dead battery,.

only why remains.

i bet it cranks jumper cable started, call AAA or buy some cables.

or swap in a charged battery , or heck charge yours, buy a charger.

check fuses.

check battery lugs for green death?

check battery voltage. at 12.6vdc, if not charge the battery

if the battery continues to disgharge.

that is called phantom drains, or bad battery .

or the alternators is bad.(system)

once started the battery volts must be 13.3.to 15v, if not the charge system is bad ,(fuses, belts slipping and lots more possibles)

Sep 19, 2014 | 2009 Jeep Commander

1 Answer

Lights wont come on and wont start


Check the Battery , Also ck the cables for gris/corrosion buildup. Check the ground cable on both ends.& clean soe there is metal to metal connection

Oct 14, 2012 | 2004 Chrysler Pacifica

1 Answer

My jeep commander wont start all interior lights and extra functions but wont start


To every one here Jeep has a problem with the positive battery Cable, check battery first then replace cable with new one, the Jeep Commander is the best thing ever it will run forever and take a beating and keep on running

May 25, 2012 | 2007 Jeep Commander Rocky Mountain

2 Answers

I have a 2004 chevy colorado and my battery died so I replaced it but the car still wont start is there a restart on truck for fuel pump?


If its spinning over good but wont fire, the computer needs to be reset . It should start then you drive it around to let it reset itself. check the pcm fuse

Jul 10, 2011 | 2004 Chevrolet Colorado

1 Answer

Wont start


Possible poor battery cable or cable connection. Remove the cable terminals from the battery, always remove ground or negative first! Use a small brass brush to clean the terminals also clean the connections too. Next follow the ground cable, to where it mounts to the body or engine. Remove this connection and clean both surfaces of cable and mounting point; re-install with proper torque on bolt. Be certain to check the cables for any short bends, thses can cause the inner cable to break and have poor connections Look for a gronding strap that runs from the firewall to engine, insure its clean with good connections. Then check the connections at the alternator, be certain that these too are clean and tight. After which reconnect cables to battery positive first ground last. Recharge the battery if she works great, you found the problem. If you still have issues it would appear your battery has or is loosing a cell and may need replace. This can be checked at an autoparts store. Lastly may be issues with charging system, alternator?

I hope this may have assited you,
Tom

Apr 22, 2010 | 2004 Mitsubishi Galant

1 Answer

06 jeep commander wont crank. No interior lights, no headlights, and when I put the key into the start position to crank it nothing happens. No clicking or sounds that make me think it is trying to turn...


Check your battery cables. Remove them and clean the contacts, if the ends are replacements take them apart and clean. Use a wire brush or sand paper. Make sure you remove the negative first and reinstall it last. Also check the battery and fuse links. Your problem is in there some where the battery, cable ends, cables, or a fuse link. If still no start let me know the results and we can go from there if need be.

Sep 20, 2009 | 2006 Jeep Commander

Not finding what you are looking for?
2000 Dodge Caravan Logo

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...