Question about Oldsmobile Cutlass Supreme

1 Answer

How to remove 90cutlass supreme 3.1l oil pan and replace gasket?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Oldsmobile Master
  • 1,727 Answers

This is actually a pretty straight forward job. but make sure you have jackstands to support the vehicle... now if you want to know how to do it, jack the car up and look at it... then ask questions when you know where the oil pan is...

Posted on Nov 09, 2014

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

MrScary66613
  • 1990 Answers

SOURCE: Oil Pan Gasket Replacement - How to - GMC Yukon 2000

No big job Really. Just locate your Drain Plug for the Oil. Thepan is right there, Remove the Bolts around the Pan and Remove. You will lose all of your oil so, Have something there to catch it all. Clean it all around the Edges of the Block where the Pan mounts with Degreaser and Make sure that you Scrape the Old Gasket off of Both the Block and the Pan. Run a Thin Bead of Blue ATV Silicone around the Pan Edge, Lay the Gasket on top of this Silicone. Put another Thin line on top of the Gasket and Reinstall. This Silicone is High Temp Silicone and will Seal Very Well. Make sure to put oil Back in the Motor! Please Rate my Response, I need all the Help That I can Get! Thanks!

Posted on Jan 27, 2009

terseo
  • 92 Answers

SOURCE: To change the oil pan gasket in a 93 Tercel

Stock the car doesn't come with an oil pan gasket but you can order one from rockauto.com you don't have to remove the A/C compressor for any of the jobs you listed. If you want to change the timing belt you need to remove the plastic rock guard under the motor on the passenger side. remove the spark plugs and using the socket turn the engine from the crankshaft clockwise until you are at TDC on #1 cyclinder. (compression stroke) Next remove the upper and lower plastic timing belt covers. The idler pulley is the one with the spring. Loosen the nut and remove the spring then you can remove the timing belt. It really isn't that hard to do. Maybe one afternoon.

Posted on Sep 20, 2009

  • 14036 Answers

SOURCE: Oil pan gasket replacement on a 2005 Escape

YEP YOU HAVE TO REMOVE FLEXIBLE EXHAUST PIPE.AND DISCONNECT THE OXYGEN SENSOR.

Posted on Apr 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove oil pan on a 2001 gmc Sonoma pick up truck to replace gasket


1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN ...

? 2:31
https://www.youtube.com/watch?v=1KsRTlnW7Cg
Sep 27, 2011 - Uploaded by JohnSmiths8379858
trying to reomove the oil pan to this truck has been sitting for about 6 ... 1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN REMOVAL "HELP!

Oil Pan Gasket: How to Change Oil Pan Gasket for 2001 ...

www.2carpros.com/questions/2001-gmc-sonoma-oil-pan-gasket
Mar 18, 2011 - How to change oil pan gasket for 2001 sonoma, can i get away with just raising the engine two inches to ... 2001 GMC Sonoma • 4 cylinder 2WD Automatic • 150,000 miles ... You need to remove the engine to get the sump off.

Nov 28, 2015 | GMC Cars & Trucks

1 Answer

How to remove oil pan


Drain the oil, remove all but four pan bolts, loosen the remaining pan bolts until they're very loose, whack the sides of the pan with a large rubber mallet to dislodge the gasket. Remove the four remaining pan bolts, lower pan to the ground.

Be ready to do everything you need to do fairly quickly; don't let that engine stand open overnight, or it'll pick up dust & condensate inside.

Jul 29, 2014 | 1994 Oldsmobile Cutlass Supreme

1 Answer

How to do a transmission fluid/filter change on a gmc 1500 2wd v8 350 step by step


Raise the vehicle. Refer to Vehicle Lifting. Place a drain pan under the transmission oil pan. Remove the oil pan drain plug. Remove the oil pan bolts. Remove the oil pan. Remove the gasket. Remove the magnet. Remove the oil filter. Remove the filter neck seal. The transmission oil pan gasket is reusable. Inspect the gasket and replace as needed. Clean the transmission case and the oil pan gasket surfaces with solvent. Install the filter neck seal. Install the oil filter. Install the oil pan gasket to the pan. Install the magnet into the bottom of the pan. Notice: Refer to Fastener Notice in Service Precautions. Install the oil pan to the transmission with seventeen bolts. Tighten the oil pan bolts to 11 Nm (97 inch lbs.) . Apply a small amount of sealant GM P/N 12346004 to the treads of the drain plug. Install the oil pan drain plug. Tighten the oil pan drain plug to 18 Nm (13 ft. lbs.) . Install Dextron Automatic Transmission Fluid. Lower the vehicle.

Jul 04, 2011 | GMC Sierra 1500 Cars & Trucks

2 Answers

What all has to be taken off to get to to the oil pan gasket


Oil Pan REMOVAL & INSTALLATION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the crankcase.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Oil level indicator harness connector, if equipped
    • Exhaust Y-pipe, if needed
    • Transaxle assembly from the vehicle.
    • Oil pan bolts and the oil pan
    To install: NOTE: The oil pan gasket is reusable unless it is damaged. Do not remove the gasket from the oil pan groove unless gasket replacement is required.
  4. Thoroughly clean the inside of the oil pan and the cylinder block contact surface. If the oil pan gasket is being reused, be careful not to damage it. Do not expose the gasket to cleaning solvents.
  5. If a new gasket is being installed, start the gasket into the oil pan groove and work the gasket into the groove in both directions. Once the gasket is exposed to oil, it will expand and no longer stay in the groove without wrinkles. If this condition exists, replace the gasket.
  6. Install or connect the following:
    • Oil pan. Torque the bolts, in sequence, to 89 inch lbs. (10 Nm).
    • Oil level indicator connector, if removed
    • Transaxle assembly, if removed
    • Y-pipe, if removed
    • Flywheel cover, if removed
    • Oil pan drain plug. Torque it to 15 ft. lbs. (20 Nm).
    • Negative battery cable
  7. Refill the crankcase.
  8. Run the engine and check for leaks. Fig. 1: Oil pan bolt torque sequence 7922vg08.gif
prev.gif next.gif

Jan 01, 2011 | 2002 Cadillac Deville

2 Answers

How do I remove the oil pan gasket from my 1999 Cadillac Deville Concours


Oil Pan REMOVAL & INSTALLATION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the crankcase.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Oil level indicator harness connector, if equipped
    • Exhaust Y-pipe, if needed
    • Transaxle assembly from the vehicle.
    • Oil pan bolts and the oil pan
    To install: NOTE: The oil pan gasket is reusable unless it is damaged. Do not remove the gasket from the oil pan groove unless gasket replacement is required.
  4. Thoroughly clean the inside of the oil pan and the cylinder block contact surface. If the oil pan gasket is being reused, be careful not to damage it. Do not expose the gasket to cleaning solvents.
  5. If a new gasket is being installed, start the gasket into the oil pan groove and work the gasket into the groove in both directions. Once the gasket is exposed to oil, it will expand and no longer stay in the groove without wrinkles. If this condition exists, replace the gasket.
  6. Install or connect the following:
    • Oil pan. Torque the bolts, in sequence, to 89 inch lbs. (10 Nm).
    • Oil level indicator connector, if removed
    • Transaxle assembly, if removed
    • Y-pipe, if removed
    • Flywheel cover, if removed
    • Oil pan drain plug. Torque it to 15 ft. lbs. (20 Nm).
    • Negative battery cable
  7. Refill the crankcase.
  8. Run the engine and check for leaks. Fig. 1: Oil pan bolt torque sequence 7922vg08.gif
prev.gif next.gif

Nov 05, 2010 | Cadillac DeVille Cars & Trucks

1 Answer

How to replace oil pan gasket on 2002 deville


Oil Pan REMOVAL & INSTALLATION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the crankcase.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Oil level indicator harness connector, if equipped
    • Exhaust Y-pipe, if needed
    • Transaxle assembly from the vehicle.
    • Oil pan bolts and the oil pan
    To install: NOTE: The oil pan gasket is reusable unless it is damaged. Do not remove the gasket from the oil pan groove unless gasket replacement is required.
  4. Thoroughly clean the inside of the oil pan and the cylinder block contact surface. If the oil pan gasket is being reused, be careful not to damage it. Do not expose the gasket to cleaning solvents.
  5. If a new gasket is being installed, start the gasket into the oil pan groove and work the gasket into the groove in both directions. Once the gasket is exposed to oil, it will expand and no longer stay in the groove without wrinkles. If this condition exists, replace the gasket.
  6. Install or connect the following:
    • Oil pan. Torque the bolts, in sequence, to 89 inch lbs. (10 Nm).
    • Oil level indicator connector, if removed
    • Transaxle assembly, if removed
    • Y-pipe, if removed
    • Flywheel cover, if removed
    • Oil pan drain plug. Torque it to 15 ft. lbs. (20 Nm).
    • Negative battery cable
  7. Refill the crankcase.
  8. Run the engine and check for leaks. Fig. 1: Oil pan bolt torque sequence 7922vg08.gif
prev.gif next.gif

Oct 29, 2010 | 2002 Cadillac Deville

1 Answer

Why my cutlass leaking oil


MOST TIME DUE TO HEAT AND STRESS GASKETS GET HARD OIL SOAKED BAKED AND CRACK.THEN YOUR VALVE COVERS LEAK.TIMING COVER CRANKSHAFT SEAL LEAKS.REAR MAIN OIL SEAL LEAKS.OIL PAN GASKETS LEAKS.THEN THEY HAS TO BE REPLACED.

Jul 22, 2010 | 1985 Oldsmobile Cutlass Supreme

1 Answer

Where are the gaskets on a 1994 oldsmobile cutlass supreme


valve covers,1/2 hour each, oil pan 1 hour,head gaskets 7 hours,transmission pan1 hour ,intake 5 hours,or exhaust manifold gaskets.4 hours

Oct 23, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

How hard is it to change the oil pan gasket on 1983 Olds Cutlass Supreme?


It is actually pretty easy. After you drain oil and loosen all pan bolts, there is just enough room to lower down and still have some room above crossmember to work around. Just make sure to scrape off all the old gasket and wipe area clean before adding new gasket. I also recommend placing thin layer of RTV Silicone evenly across both surfaces. (pan and engine block) Then use your new gasket in between like usual. Check repair manual for oil pan torque specs. I believe most are around 15 lbs.
Full Free Online Repair Manuals and component locations, diagrams, testing, replacing, and more if you register for free at www.autozone.com

Aug 26, 2009 | 1983 Oldsmobile Cutlass Supreme

3 Answers

Oil Pan Gasket Replacement - How to - GMC Yukon 2000


No big job Really. Just locate your Drain Plug for the Oil. Thepan is right there, Remove the Bolts around the Pan and Remove. You will lose all of your oil so, Have something there to catch it all. Clean it all around the Edges of the Block where the Pan mounts with Degreaser and Make sure that you Scrape the Old Gasket off of Both the Block and the Pan. Run a Thin Bead of Blue ATV Silicone around the Pan Edge, Lay the Gasket on top of this Silicone. Put another Thin line on top of the Gasket and Reinstall. This Silicone is High Temp Silicone and will Seal Very Well. Make sure to put oil Back in the Motor! Please Rate my Response, I need all the Help That I can Get! Thanks!

Jan 27, 2009 | 2000 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...