Question about 2009 Chevrolet Impala
I need to locate the CKP on a 2009 chevy impala
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
1990 Chevrolet Cavalier 2.2L TBI 4cyl
The Crankshaft Position Sensor is located under hood, center, rear engine area, below ingnition coil pack and DIS module, mounted in engine block.
Fig. 1: View of the CKP sensor-to-crankshaft reluctor relationship
Crankshaft Position (CKP) Sensor
A magnetic crankshaft sensor (Hall Effect switch) is used which is remotely mounted on the opposite side of the engine from the DIS/IC module. The sensor protrudes in to the engine block, within about 0.050 in. (1.27mm) of the crankshaft reluctor.
I really hope help you wuth this (rated this help). have a nice day, good luck.
Posted on Sep 25, 2009
Testimonial: "Awesome. Thanks."
It mounts in the side of the block near the crankshaft,it fits in a hole,going into the engine block.,look on the inside of the engine compartment ,on the firewall side,left of the pulleys,down low.
Posted on Mar 22, 2010
should be on bottom of crank on left side behind the pulley.. the big metal ring with teeth on it on front side of motor..
Posted on Dec 02, 2011
SOURCE: 2004 3.8 Chevy impala sensor
The crankshaft positions sensor is located behind the crankwheel on the
passenger side of the engine. In order to replace it or at least
examine it, a person would need to remover the crankwheel with a puller
that can be rented out at Autozone. Just ask for a harmonic balancer
puller. Remove the front right tire and place firmly on jackstands. The
crankshaft pulley WILL NOT loosen by just turning the bolt. This is a
two person job. Caddycorner to the starter, there is a small plastic
plate cover that covers the driveplate/flexplate. Remove the two bolts
and pull the cover off. Have one person position a screwdriver into the
ring gear teeth and have another remove the pulley bolt. Its EXTREMELY
TIGHT and the best way to remove it is with a large rachet and a breaker
bar. Once the bolt is removed, take the puller and position
accoridngly. The threaded holes are not on the surface but inside the
pulley itself. Place large bolt in center of the puller and place the
pointed or flat tip on center of the large bolt and place. Take three
very small screws or bolts that came with the puller and position all
three in place. Once all this is done begin turning the bolt in the
middle of the puller clockwise. This will take alot of arm strength and
anywhere from 15-30 min to do. Once the wheel has come off, carefully
pry off the sensor cover which is another piece of plactic. Once the
cover is off, carefully remove the sensor and examine or replace as
needed. Installation is reverse of removal. Hope this helps
Read more: http://wiki.answers.com/Q/Where_is_the_crankshaft_position_sensor_on_2001_Impala#ixzz1xaQZV1IR
Posted on Jun 12, 2012
Testimonial: "Thanks a lot... I'll be taking it to a shop. "
Tips for a great answer:
Dec 10, 2016 | Cars & Trucks
Engine control module (ECM) replacement
Crankshaft damper replacement
CKP sensor replacement
Any engine repairs which disturb the crankshaft to CKP sensor relationship
Important: The scan tool monitors certain component signals to determine if all the conditions are met to continue with the CKP system variation learn procedure. The scan tool only displays the condition that inhibits the procedure. The scan tool monitors the following components:
CKP sensor activity--If there is a CKP sensor condition, refer to the applicable DTC that set.
Camshaft position (CMP) signal activity--If there is a CMP signal condition, refer to the applicable DTC that set.
Engine coolant temperature (ECT)--If the engine coolant temperature is not warm enough, idle the engine until the engine coolant temperature reaches the correct temperature.
Apr 04, 2016 | Chevrolet Cars & Trucks
Oct 26, 2015 | Buick Cars & Trucks
Crankshaft Position Sensor Operation?
Replace Camshaft position sensor and Crankshaft Position Sensor? http://technoanswers.blogspot.in/2012/06/2005-dodge-durango-replace-camshaft.html
GMC Crankshaft Position (CKP) Sensor Replacing? http://schematicsdiagram.blogspot.com/2011/12/gmc-crankshaft-position-ckp-sensor.html
These details will help.
Nov 25, 2012 | 2000 Cadillac Escalade
Fig. Crankshaft Position (CKP) sensor (7)
Ford Taurus 2008-2009
Mercury Sable 2008-2009
The Crankshaft Position (CKP) Sensor is a permanent magnet output coil device that monitors the speed and position of the crankshaft. A reluctor is attached directly to the crankshaft, and is used to generate a constant signal as it passes the CKP sensor magnetic coil. The CKP Sensor utilizes system voltage (12 volts DC), or reference voltage (5 volts DC) to generate a digital output signal to the PCM that is based upon a 0.5 volt AC reference. The alternating magnetic field is used by the sensor output electronics to produce a digital pulse. The CKP sensor returns a digital ON/OFF signal pulse during each revolution of the crankshaft, with a momentary signal interrupt for the top dead center (TDC) position of the #1 cylinder. The Pulse Width Modulation pattern is used by the Powertrain Control Module (PCM) to calculate ignition timing, fuel injector timing, misfire diagnostics, and the tachometer display
Jun 20, 2012 | 2008 Ford Taurus X
Mar 24, 2011 | 1997 Pontiac Sunfire
Nov 06, 2010 | 2000 Chevrolet Impala
Apr 15, 2010 | 2002 Ford Escape
Sep 25, 2009 | 1990 Chevrolet Cavalier
Apr 12, 2009 | 1995 Chevrolet Monte Carlo
383 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: