Question about Cars & Trucks

1 Answer

How can i remove a manual transmission from 1991 chevy truck 1500

5 gear

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Cars & Trucks Master
  • 2,485 Answers

Undo the tail shaft bolts remove shifter remove mounts , undo bolts around bell housing.

Posted on Nov 09, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

PyroPCMan
  • 405 Answers

SOURCE: 1991 Ford Ranger manual transmission remove

444a343.jpg

  1. Disconnect the negative battery cable.
  2. Remove the gearshift lever assembly from the control housing.
  3. Cover the opening in the control housing with a cloth to prevent dirt from falling into the unit.
  4. Raise the vehicle and support it safely.
  5. On 2WD vehicles, matchmark the driveshaft to the rear axle flange. Position a drain pan under the tailend of the transmission. Remove the driveshaft-to-rear axle flange fasteners and pull the driveshaft rearward to disconnect it from the transmission.
  6. Disconnect the clutch hydraulic line a the clutch housing. Plug the lines.
  7. Disconnect the speedometer from the transfer case/extension housing.
  8. Disconnect the starter motor, back-up lamp and, if equipped, neutral sensing switch harness connector.
  9. Place a wood block on a service jack and position the jack under the engine oil pan.
  10. On 4WD vehicles, remove the transfer case from the vehicle.
  11. Remove the starter motor.
  12. Position a transmission jack, under the transmission.
  13. Remove the transmission-to-engine retaining bolts and washers.
  14. Remove the nuts and bolts attaching the transmission mount and damper to the crossmember.
  15. Remove the nuts and bolts attaching the crossmember to the frame side rails and remove the crossmember.
  16. Lower the engine jack slightly to angle the transmission assembly. Work the clutch housing off the locating dowels and slide the clutch housing and the transmission rearward until the input shaft clears the clutch disc.
  17. Lower the transmission jack and remove the transmission from the vehicle.
To install:
  1. Check that the mating surfaces of the clutch housing, engine rear and dowel holes are free of burrs, dirt and paint.
  2. Place the transmission on the transmission jack. Position the transmission under the vehicle, then raise it into position. Align the input shaft splines with the clutch disc splines and work the transmission forward into the locating dowels.
  3. Install the transmission-to-engine retaining bolts and washers. Tighten the retaining bolts to specifications. Remove the transmission jack.
  4. Install the starter motor. Tighten the attaching nuts.
  5. Raise the engine and install the rear crossmember, insulator and damper and attaching nuts and bolts. Tighten and torque the bolts to specification.
  6. On 4WD vehicles, install the transfer case.
  7. On 2WD vehicles, insert the driveshaft into the transmission extension housing and install the center bearing attaching nuts, washers and lockwashers. Connect the driveshaft to the rear axle drive flange.
  8. Connect the starter motor, back-up lamp and, if equipped, neutral sensing switch connectors.
  9. Connect the hydraulic clutch line and bleed the system.
  10. Install the speedometer cable.
  11. Check and adjust the fluid level.
  12. Lower the vehicle.
  13. Install the gearshift lever assembly. Install the boot cover and bolts.
  14. Reconnect the negative battery cable.
  15. Check for proper shifting and operation of the transmission.
The above was pulled frrom:
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800391da

hope this helps

Posted on Jul 02, 2008

  • 32 Answers

SOURCE: 1988 Chevy truck

no try looking at the governer on the back should be a cover about 4 in arond remove and look to see if the plastic teeth are broken or worn.

Posted on Mar 17, 2009

  • 41 Answers

SOURCE: I have a 93 Chevy Suburban 1500 and the

yes just change out the tail shaft the electric speed o into the older one i just changed out a 84 to a 93 trans very easy

Posted on Jun 25, 2009

wilsodfarm
  • 986 Answers

SOURCE: 1999 chevy truck 1500 is sluggish and hesitates

sound like your catilitic converter is plugged up.

Posted on Jul 27, 2009

Molson02536
  • 3854 Answers

SOURCE: what transmission will interchange with my truck a

You can replace it with another 4L60E 1998 and newer and you can upgrade it to the 4L65E which is the same but uses 5 planetary gears in stead of 4 that is used in the 4L60E.
1998 was the change off year i believe where they started to section off the transmission in to three parts. The bell housing, body and tail end. The tail shaft housing uses 5 bolts to connect to the transmission and the 1997 transmission and earlier uses 4 bolts, but internal parts had no changes other then the 4L65E.
Thank you for using fixya and good luck.

Posted on Apr 27, 2010

Testimonial: "thank alot"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What transmissions are compatible with 1991 chevy silverado 1500 extra cab


Have a look on Ebay:
http://www.ebay.com/bhp/chevy-silverado-1500-transmission

Mar 13, 2016 | Chevrolet Silverado 1500 Cars & Trucks

2 Answers

I'm looking at purchasing a 96 chevy c10. It has the 5.7L vortec with manual 5spd transmission. While test driving the transmission grinds in 2nd gear everytime you shift gears. All other gears shift...


The synchronizers are bad. Costs about $200. But I check and replace bearings. Also check gears. About a $1500 job. You pull the transmission. I pull, $2500. I replace the master and slave also.

Feb 21, 2015 | Chevrolet Cars & Trucks

1 Answer

1991 chevy 1500 5.7 no reverse


The transmission your put in is also faulty, you will have to do the job all over again.

Nov 19, 2013 | Chevrolet Cars & Trucks

1 Answer

2002 chevy silverdo 1500


The first thing to do is drain and refill the transmission with fresh lub, it uses ATF (type Mercon 5) in all Ford manuals.

Jun 01, 2012 | 2002 Chevrolet Silverado 1500

1 Answer

How to replace bearing in a 1991 chevy 1500 4x4 rear axel at driveshaft?


To replace pinon bearing you need to pull wheels and the brake drums off next pull cover off the back of the rear end (make sure you have a drain pan under rear end) next turn dive shaft till you see a small bolt remove bolt pull center pin out push axle in pull c clips out pull axels out remove four bolts holding ring and spider gears remove gears assembly next remove drive shaft remove bolt from pinon push pinon in remove seal and bearing

Jun 27, 2011 | 1991 Chevrolet K1500

1 Answer

Just replaced flywheel on my 1991 gmc 1500 truck. will drive in all gears but it will not go past 40mph into next gears. also when truck is in drive you can still start truck


Sounds like your linkage is out of whack. You need to readjust the linkage so it goes through the whole range. Sounds like you are not in drive when the gear selector says you are. Undo the linkage, put the transmission in park manually then reattatch linkage to make sure that what it states on the selector is concurrent with the transmission. Good luck.

Jan 03, 2011 | 1991 GMC C1500

1 Answer

92 chevy s10 4x4 4.3L manual transmission no 3rd gear


Hi:

Your transmission has 3 shift rails...
1st - 2nd
3rd -4th
5th- Reverse

If your 3rd gear doesn't work , you have an internal transmission problem, such as a syncronizer, or similar fail... There is not much you can fix, without removeing the transmission.

Nov 30, 2009 | 1992 Chevrolet S-10

1 Answer

Wont/shift/in/passing/gear


Check to see if the transmission tv shift cable is attached to the throttle body. Are the shift point all high?

Mar 06, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

1991 chevy Suburban 1500 Scottsdale gear ratio


look in glove box or on tag on rearend on cover if both are gone divide number or ring gear teeth into number of pinion gear teeeth

Dec 15, 2008 | 2002 Ford E350

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...