Question about Ford E-150

1 Answer

Dose the clutch adjuster on a 83 e150 van have bushings?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 14,585 Answers

Yes it does. Yours would be a brass bushing. Find something suitable. Brass or plastic. You can make your own....

Posted on Nov 09, 2014

Testimonial: "thank-you................"

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
aneciap073
  • 12 Answers

SOURCE: 83 e150 0wners manual

Go to: www.ford.fleet.com
Click on 'Maintenance' then 'Owners Manual'
Enter make & model and files will be auto generated. Follow directions or just click on the file you need. A new window will open with your file as a PDF. Make sure you have a free copy of Adobe or other reader for this,(adobe.com.) You can save from here or read page by page without saving.
This is FREE ! I searched the web forever to find this site when I needed the manual for my Ford Expl Sport Trac.

Posted on Jul 03, 2009

  • 57 Answers

SOURCE: clutch self adjuster on a k reg escort van

the self adjust mechanism is made up of two pieces a pawl and ratchet. removing them is more awkward than difficult. you need to remove the clutch pedal by knocking out the pivot shaft that also supports the brake pedal just knock it out far enough to remove the clutch pedal after removing the clip. when the pedal is out you will see how it is assembled. the hardest part of the job is replacing the spring which is attached to the pedal this must be hooked back into the pedal last i find a strong piece of wire threaded through the hole in the pedal does the trick this is a job for someone who has some experience good luck

Posted on Aug 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 ford E150 van compressor clutch not stay engaged are will not engage


sounds like its low on refrigerant 134a id check your pressures and like he said bypass low pressure switch, mike

Jun 24, 2017 | Ford Cars & Trucks

2 Answers

E150 ford van, it has reverse but no forward. 5.0 engine with I beleive a c6 transmission.


FIRST CHECK THE TRANS FLUID. IS IT DARK BROWN OR BLACK AND SMELL BAD? IF SO CLUTCHS ARE BURNED UP. TIME FOR A REBUILD

Dec 19, 2014 | Ford Cars & Trucks

1 Answer

The switch of the bed in my ford e150 van don't


test the 1) fuse 2) switch 3) tight the connector 4) small motor with VOM. and fix it.
God bless you

Jul 24, 2013 | Cars & Trucks

1 Answer

I have a 98 Nissan200sx 1.6l jst put a new clutch in and now the clutch padel gos to the floor n stays there. I was told maybe a new clutch cable would fix it but same thing I didnt put the pilot bushing...


The pilot bearing is the input bushing,this has nothing to do with the cable going to the floor and staying there,The clutch calbe is adjustable . You adjust it by pulling on the cable and leave a 1/4 freeplay your problem is you need to adjust the cable3_26_2012_4_14_57_am.jpg

Mar 25, 2012 | 1998 Nissan 200SX

1 Answer

1995 e150 ford van,, 4.9 6cyl i need to replace the bushings on the radius arms. do i need to remove the springs or do the radius arms , just unbolt (front and the back) and remove? i appreciate your help....


Hi Darrell,
No the springs will remain in place,You will need new bolts and nuts before you start the job,they are 1/2 x one inch.you'll need five of them.unfortunately there are three large rivets you will need to torch off besides the other three bolts and nuts. Remove the radius arm nut and outer bushing before you loosen the arm.
good luck

Dec 29, 2009 | Ford E-150 Cars & Trucks

1 Answer

Just bought 99 Hombre. My clutch pedal dose not work right


yes you can adjust the clutch unless it is already adjusted as far as it can be then you may have to replace it

Aug 30, 2009 | 1999 Isuzu Hombre

1 Answer

I want to swap engine and trans. from wrecked 92 E150 van to 87 E


You can swap just the transmission unless the shifter is on the column,then you will need the column as well,You don't need the engine if your is still good.

May 06, 2009 | 1987 Ford Econoline

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...