Question about Cars & Trucks

1 Answer

One injector on my Daewoo Lanos just stopped working. What's the problem? How can I fix it?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 103 Answers

First I would try wynns injector cleaner you can buy it at most servos make sure you buy the right product for your vehicle follow instructions on container

Posted on Nov 09, 2014

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: User manual for daewoo lanos car

Need code to work radio. Replaced the battery and it is asking for a code for the radio to work

Posted on Feb 12, 2009

emjem74
  • 162 Answers

SOURCE: Daewoo Lanos Engine Number

should be on a small seperate plate located no the front of the engine compartment. if not there then check on the back of the engine compartment for a small section with your serial stamped into it. if there are none of the above then i would check for stolen recovered.

Posted on Feb 25, 2009

emissionwiz
  • 75822 Answers

SOURCE: Where is the timing mark for the camshaft on a 2000 Daewoo Lanos?

Here is the entire timing belt replacement procedure.
Required tools:
13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers
If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.
Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley ( the 4 Allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pulley) on the camshaft pulleys -- ( intake cam line up the line on the pulley with the line on the inner cover)( exhaust cam line up the arrow on the pulley with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the Allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhaust Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal.

To clarify, on the DOHC engine, the intake cam gear has a line on it, and the exhaust cam gear has an arrow on it. These should be lined up with the corresponding line and arrow on the VALVE COVER, pointing straight up. I just went through this process over the weekend, and spent quite a bit of time looking for these marking as I had removed the valve cover. Once I found them, it was plain and simple.
In addition, be sure to not over tighten the belt when reinstalling. The tensioner has markings on it for "old" and "new". DO NOT adjust past "new", as the car will sound like a jet engine, and the belt will not last for very long.
One more item that you may as well replace while you are in there is the cam position sensor if you have not already, as there have been issues with them, and the timing housing has to be opened to get to it

Posted on May 22, 2009

stevenhurc
  • 450 Answers

SOURCE: 2001 Daewoo Lanos Fault 63.58X 'B'

DTC 63 Will Set When
No voltage is supplied by the ECM through the EST “B” line while reference pulses are received by the ECM from the crankshaft position sensor
check white wire terminal B on ignition coil to ECM terminal C14 for open circuit or short to ground while disconnected if thats ok check for voltage signal at B while cranking no signal ECU faulty. voltage signal also on A terminal while cranking and check earth terminal C to body no higher than 5 Ohms
power is terminal D 12V
if getting power, earths good, and both signal voltages are going into coil pack, coil pack is faulty.

Posted on Jun 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why my daewoo leaks oil into the injectors?


The oil can't get into the injectors it must be getting around the injector body seal ,then causing this problem ,renew the seals .

Dec 20, 2014 | Daewoo Lanos Cars & Trucks

1 Answer

2000 daewoo lanos code po202 po302


It is P0202 and P0302
P0202 - Fuel Injector Circuit Malfunction Cylinder 2
Most likely cause a failed fuel injector or shorted wiring harness.
P0302 is a misfire in cyinder #2 from the injector problem.

Nov 05, 2012 | 2000 Daewoo Lanos

1 Answer

What is included in a 60,000 mile tune up on a Daewoo Lanos


spark plugs,wires,airfilter,gasfilter,belt,pcv valve if included in car, oil change, and clean injectors.

Feb 06, 2010 | 2001 Daewoo Lanos

1 Answer

Have got Daewoo Lanos DOHC model 1997 experiencing late/hard start if sitting for 1hr and worst of all if its when it sits overnight, one tries for 10-20 seconds to get it starting, any clues? Thanks...


Your injectors need cleaning. Try some fuel injector cleaner pour it in the fuel tank and drive around. Change your air filter. Clean Throttle Body with carburetor cleaner.

Jan 10, 2010 | 2000 Daewoo Lanos

1 Answer

2000 Daewoo Lanos 'jumps' when pulling away and in low gears.


Ignition Coil, or Crankshaft sensor going bad. Change your spark plugs and wires then see what happens. Or could be your injectors are clogged. Try some pour in the tank Fuel Injector Cleaner like STP. Any little debris can mess them up.

Oct 31, 2009 | 2000 Daewoo Lanos

1 Answer

2002 Daewoo Lanos blinker problems


change the switch in the steering collum

May 15, 2009 | 2002 Daewoo Lanos

1 Answer

Car start missing after travelling 80km. then we stop car for one minute and start car car runs smoothly upto 50km and so on


replace spark plugs and wires .clean injectors fill gas tank up add a bottle of prestone fuel injector cleaner.

May 10, 2009 | 2001 Daewoo Lanos

1 Answer

Daewoo espero fuel injector


Try fuel injector cleaner. It is a solution/ solvent like that you pour into your fuel tank. It works perfectly well and great for cleaning that.

Good luck.

Rate this please.

Apr 27, 2009 | 2002 Daewoo Lanos

1 Answer

That happens to him?


hi
may be there is faulty of a surety system or immobilizer system that stopped the injectors energy
ask for more information
give us more details to have more help from us
with my best wishes

Jul 14, 2008 | 1999 Daewoo Lanos

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...