Question about 1988 Chevrolet S-10

1 Answer

Which fuse is for cargo light on a 1988 Chevy s10 pickup?

Posted by on

  • Tonya collins
    Tonya collins Nov 10, 2014

    I only remember hooking up two wires to the dome light. is there a wire from dome light to cargo light?

  • Tonya collins
    Tonya collins Nov 10, 2014

    dome light has been working fine. Cargo light worked briefly after I changed some fuses, then quit. bulb is good to cargo light to. no fuse marked dome light, cargo light , or interior lights.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,585 Answers

The cargo light is tied to the interior/dome lights. If you have a dome light then the bulb is bad or it has a broken wire. If not, then check the dome light fuse. In the fuse panel under the dash.

Posted on Nov 09, 2014

Testimonial: "Sorry, but dome light I replaced and has worked fine for several months. Cargo light worked very briefly when I was changing fuses several months ago but has not worked since. There is no fuse marked as dome light or interior lights."

  • Randy Ohler Nov 10, 2014

    Your dome light is working. So should the cargo light. You'll have to check the light bulb from the cargo. Or check the wiring. The dome and the cargo are on the same wires.

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 1998 Chevy S10 pickup backup lights don't work

Yes it screws in on right side of tramission and you will need a 7/8 inch deep socket to remove it. You may be able to clean the old one once it is removed. There is a little ball thatgets dirty and may you can get by with cleaning it. Good Luck. Ed

Posted on Sep 06, 2008

  • 1596 Answers

SOURCE: I need to replace the fuel pump in my 1985 Chevy S10 Pickup.

EXACT PROCEDURE ! Please Rate Me Fairly for this!! Thank you And Good Luck !!


ELECTRIC PUMP

REMOVAL

  1. Before servicing the fuel pump the fuel system pressure must be relieved. See: Fuel Pressure Release
  2. Disconnect the negative battery cable.
  3. Raise the car on a hoist.
  4. Remove the fuel tank. See Fuel Tank / Service and Repair.
  5. Remove the fuel tank sending unit and pump assembly by turning the cam lock ring counterclockwise. Lift assembly from the fuel tank.
  6. Pull the fuel pump up into the attaching hose while pulling outward away from the bottom support. Take care to prevent damage to the rubber insulator and strainer during removal. After the pump assembly is clear of the bottom support, pull the pump assembly out of the rubber connector for removal. NOTE: Inspect the fuel pump attaching hose for any signs of deterioration. Also check the rubber sound insulator at the bottom of the pump. Replace damaged or deteriorated parts.
INSTALLATION
  1. Push the fuel pump assembly into the attaching hose.
  2. Position the fuel tank sending unit and pump assembly into the fuel tank. Use a new "O" ring seal. NOTE: Care should be taken not to fold over or twist the strainer when installing the sending unit as this will restrict the flow of fuel. Also, verify that the strainer does not block the full travel of the float arm.
  3. Install cam lock over the assembly and lock by turning clockwise.
  4. Reinstall fuel tank.
MECHANICAL PUMP

REMOVAL and INSTALLATION

NOTE: To ease pump installation, rotate the camshaft so the camshaft eccentric is out of the way of the fuel pump rocker arm.

  1. Disconnect fuel lines from fuel pump.
  2. Remove fuel pump mounting bolts and the fuel pump.
  3. Remove all gasket material from the pump and block gasket surfaces. Apply sealer to both sides of new gasket.
  4. Position gasket on pump flange and hold pump in position against its mounting surface. Make sure rocker arm is riding on camshaft eccentric.
  5. Press pump tight against its mounting. Install retaining screws and tighten them alternately.
  6. Connect fuel lines. Then operate engine and check for leaks.

Posted on Mar 22, 2009

  • 10 Answers

SOURCE: fuse diagram on chevy s10 pickup extended cab.

behind the radio, take the radio and the cover that goes over it. it should be there next to the hazard ligths flasher.

Posted on May 28, 2009

  • 1 Answer

SOURCE: Chevy S10 Pickup Starter. Removed the two bolts

Just changed a starter in a 94 S10 4x4. The only way to remove the starter was to take the passenger side exhaust manifold off and bring the starter out that way. Installation the same in reverse. Hope this helps. Don

Posted on Jun 25, 2009

  • 740 Answers

SOURCE: 1997 Chevy S10 pickup Fan switch for heater runs on high only.

replace the blower motor resistor located on the heater box were the blower motor is located the wiring to the blower may go to it. This is very easy to locate if you buy the part first.

Posted on Jan 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the two flashers located on 1988 chevy s10 extended cab pickup


One should be on the fuse box under the instrument cluster, and the other is in the wiring harness behind the radio.

Feb 18, 2015 | Cars & Trucks

1 Answer

1988 Chevy s10 pickup 4wheel, small 6; looking for firing order


if its a 2.8L then 123456, can't remember the 4.3L. just type the question in your address bar,include engine size for more accuracy.

Jan 17, 2011 | 1988 Chevrolet S-10

1 Answer

How to fix the tail lights on a 1988 chevy pickup


Sounds like the fuse for the Tail Lights Is Blown.

Jul 29, 2010 | 1988 Chevrolet C1500

1 Answer

Can a 1988 chevy S10 2.5l ecm be used in a 1987 chevy S10 2.5l


the numbers on the ecm must be the same . you have 2 sets of numbers and the bottom set should be the same.

Jul 15, 2009 | 1987 Chevrolet S-10 Pickup

1 Answer

Where is the fuel pump fuse on a 1989 chevy s10 pickup?


Fuses for the engine or exterior items are under the hood in a little black plastic box.

Fuses for the interior items are under the dash, up above the driver's left foot.

In either case, the fuse diagrams should be on the inside of the fuse cover.

Jun 09, 2009 | 1988 Chevrolet S-10

1 Answer

1988 Chevy S10 Durango Pickup, Won't start will fire


sounds like ignition module inside of distributor cap under distributor rotor button.these do go bad and can easily be replaced.strong suspicion from your details that this is the culprit.

May 09, 2009 | 1988 Chevrolet S-10

2 Answers

No tail lights


Try checking the headlight switch it may have broken contacts in it. Easy fix go to a salvage yard find same make and model truck, swap headlight switches.

Dec 27, 2008 | 1997 Chevrolet S-10 Pickup

Not finding what you are looking for?
Cars & Trucks Logo

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...