Question about Jeep Commander

1 Answer

Check engine light on 2007 jeep commander, p0750 code. How to fix it.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 2,474 Answers

What motor do you have

Posted on Nov 09, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
moparownr
  • 667 Answers

SOURCE: TRANSMISSION PROBLEM

You have a shift solenoid problem, it will probably have to be replaced, it will require taking off the transmission oil pan (draining trans oil), I recommend that you leave this task to a repair shop, it is a little tricky to do and it is very important that the inside of the transmission stays very clean. I hope this helps you, please let me know

Posted on Jun 03, 2009

  • 323 Answers

SOURCE: 2006 jeep wrangler check engine light came on it

There is a software update for the PCM that addresses this issue. TSB 18-028-06

Posted on Jun 08, 2009

joecoolvette
  • 5660 Answers

SOURCE: 2007 Jeep Commander will not start

Check the battery cables, then go to the starter relay, then the starter, (If the lights are bright when you turn them on)

Posted on Aug 01, 2009

BCally1
  • 133 Answers

SOURCE: 2007 jeep commander rocky mountain no sound from radio

take it to the dealer. they will put a new radio in it if you have under 36000 miles

Posted on Sep 12, 2009

emissionwiz
  • 76649 Answers

SOURCE: P0700, P0750 and P0755 codes

P0700 (M)
Check Transmission DTC's
This code indicates that the EATX (Transmission controller) has an active fault and has illuminated the MIL via a BUS message. The specific fault must be acquired from the EATX via a DRBIII tool. (Input or Output Speed Sensor failures often cause this code and are a common failure part on WJ Grand Cherokees

P0750
Shift Solenoid circuit.
Note: If code P1767 (Transmission Relay Always On) is also present: Replace transmission solenoid assembly. See note provided. When transmission is in limp mode the relay that provides power to the solenoid group is switched off. This is normal and is designed to provide operation in one gear only. Engineering department suggests to replace transmission solenoid assembly anytime these two trouble codes occur together. See applicable service manual section (21) for solenoid assembly replacement directions. IMPORTANT: When performing this repair always check torque on all valvebody accumulator cover plate screws. Proper torque specification is 70 inch pounds. If any accumulator cover plate screws are damaged or missing replace the valvebody assembly. NOTE: If any other trouble codes are present do not replace solenoid assembly. See test in the applicable Transmission Diagnostic Procedures Manual

P0755
Shift Solenoid B

Posted on Oct 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 Jeep Commander Check engine light is on (but that has been on for awhile.) Electronic Throttle Control (ETC) warning light just came on and my temperature doesn't move very from C. Any ideas?


thermostat is bad probably, not sure if the xk has a built in obd or not but turn the key on and off (almost till starting) 3 times called the key dance should spit a code on your led readout below spedo

Mar 23, 2017 | Jeep Commander Cars & Trucks

1 Answer

How to reset check engine light on 2007 jeep compass limited


you need a scan tool pull code and then you can clear trouble codes. if cause of code not fixed check engine light will come back on.

Jul 11, 2014 | 2007 Jeep Compass Limited

1 Answer

2008 Jeep Grand Cherokee Limited 5.7 Hemi Check engine light on, code P0750


2008 jeep cherokee (hemi) engine light its on i brought to fix they change 4 sensor and the converter. After 5 days engine light comes on again, what else can be? im depress about it, after paying almost 2 grand to fix this issue.

Jan 25, 2014 | Jeep Grand Cherokee Cars & Trucks

1 Answer

The check engine light is on my 2007 jeep commander


Usually is one of your sensors but you can get it checked by auto zone for free on the diagnostic machine..

Mar 16, 2013 | 2007 Jeep Commander 3.0

1 Answer

I have a 2007 jeep commander 3.7 reading a code p0032 after i replaced the o2 sensor with a ngk it is still reading the code what do i do next?


Check your wires. You may have a bad connection or broke wire. other than that you may have an issue with it running too rich or lean. The o2 sensor will turn on the check engine light if its out of specs.

Jun 14, 2012 | Jeep Commander Cars & Trucks

1 Answer

I have a 2007 jeep grand cherokee,engine light keeps coming on.it has a 4.7 engine.had it to the dealer 4 times.the service code that keeps coming back is p013c.thanks for any help.


I have run into the same problem in my 07 Commander. It is the oxygen sensor. IT is described as the downstream (before the catalytic converter)sensor 2 on bank 2 which is the drivers side of the cylinders. This is what I have been told from a member on the forum that I am on. I am still waiting back to hear from the dealership to have them fix my problem. I too have been there 4 times too.

Jun 09, 2010 | 2007 Jeep Grand Cherokee Overland

4 Answers

2007 Jeep Commander will not start


Check the battery cables, then go to the starter relay, then the starter, (If the lights are bright when you turn them on)

Aug 01, 2009 | 2007 Jeep Commander Rocky Mountain

1 Answer

2007 sport commander


it would seem that your vehicl is in limp in/ engine protect mode this typ of problem should be under warrenty you need to take it to the dealership to have this fixed at no cost. hope this helps. please rate this solution. thanks

Aug 30, 2008 | 2007 Jeep Commander Rocky Mountain

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...