Question about Chrysler Voyager

2 Answers

Why my headlights high beam is out on one side low beam out on other side?

I changed the light bulbs and continue to have the same problem. I put in series 9007 bulbs as suggested by the owners manual and the auto parts store.

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Chrysler Expert
  • 405 Answers

Some cars have Quad headlights/ seperate high and low on each side. Check to see, if not ,then in the relay box, fuses and relays for headlights. It is up by battery in engine compartment.

Posted on Jan 09, 2015

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 2,474 Answers

Check your head light relay and some models use a lighting control module LCM

Posted on Nov 08, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 260 Answers

SOURCE: Low Beam

Make sure you have a good switch
bulbs good
relay and or fuse is good

Posted on Apr 11, 2009

  • 12 Answers

SOURCE: high beam headlight does not work properly

it more then likey a lose wire or bear one. run the line down. i think that the high beams run on diff. fuses. you can try that!

Posted on Jul 13, 2009

geaeri95
  • 127 Answers

SOURCE: headlight low beam

Test to see if you have voltage at the bulb connector in low beam position. I'd almost bet that if there is no voltage there for the low beams that you have a bad high/low switch.

Posted on Oct 03, 2009

  • 347 Answers

SOURCE: no low beam only high beam

check the ground connection of the bulbs. check the light switch. the headlight relay is located under the dash or under the hood.

Posted on Nov 27, 2009

  • 2 Answers

SOURCE: Daytime Running Lights Inoperative 2002 Toyota Camry

[Information] For a 2002 Toyota Camry, the Daytime Running Lights (DRL) operate utilizing the High Beams (inner Lamps closer to the center of the vehicle front) at a reduced power.

[The troubleshooting process:] Review the Owner's Manual and ensure the test configuration matches the following criteria:
1. According to the 2002 Toyota Camry Owner's Manual (Check your Owners Manual):
"The DRL system will make your headlights come on at a reduced brightness when:
The light switch s in the "DRL" position.
The ignition is on with the engine running.
The headlight switch is off.
The parking brake is released."


2. Set the Test Conditions according to Step 1 above.

3. Check the headlight bulbs to ensure they are not burned out. If one burns out, there is a fair chance that the other would have burned out at the same time. Replace as necessary. In this case, if the high beams operate, the DRLs should also operate.
4. Test the system, ensuring the step 1 conditions are set. (Engine running, Multi-function Switch on Turn Signals in "DRL" position, headlight switch off (repeating what the manual says -- it should be obvious that in the "DRL" position, the headlight switch should be off / do not have the switch positioned to "High Beam"), and the Parking Brake "off").
5. If DRL lights do not work, check the engine compartment Fuse and Relay Box. there is a 5 Amp DRL fuse -- replace it with the spare. Test (step 4).
6. If it does not work, swap around or replace relays -- there are three (3). Any one of them could be bad (stuck or burned out). Test (step 4).
7. Other less likely possible issues could be that the Multi-function Switch is broken or a connection / wire is broken. [Beyond the scope of this process.]


My problem was that the test configuration did not have the engine running and parking brake off - Step 1. Problem solved with much thought, repetitive tests on the vehicle and going back to the basics -- what does the Owner's Manual say and where are the applicable fuses and relays located?

Posted on Jan 01, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Driver side headlight goes dim on high beam while passenger side is bright


bad connection or bad earth check all connection or bulb

Jan 24, 2016 | Cars & Trucks

1 Answer

Driver side low and high beam on but dim. Passenger side low beam normal but high beam on and dim


I would check for the groundwire continuity

Driver side - dim low beams and no hi beam - Subaru Outback ...

www.subaruoutback.org > ... > General > Electrical & Electronics
Oct 11, 2014 - Hi everyone, My drivers side headlights are dim on low, (car has separate bulbs ... When the headlight switch is turned ON, but for low beams, ...

Driver-side Low beam Not Working (electrical issue not bulb ...

www.hummer4x4offroad.com/.../showthread.php?...Driver-side-Low-be...

Mar 12, 2015 - 10 posts - ‎4 authors
The high beam continues to work on both sides...I pulled the Driverside headlamp fuse and then both left and right beams lit up but very dim.

High beams ok, but not low beam - one side only - TDIClub Forums

forums.tdiclub.com > ... > VW MKIV-A4 TDIs (VE and PD)
Jan 23, 2014 - My driver's side lights are working fine - high and low beams. ... But it definitely looks like the big lamp on the driver's side gets brighter when ..... Drivers side headlight is very dim on low beam and goes out when on high beam ...

Dim driver's side headlight (low & high beam) - GrandAmGT.com Forum

www.grandamgt.com > ... > Technical Q&A

Dec 11, 2002 - 6 posts - ‎4 authors

Jan 04, 2016 | Cars & Trucks

2 Answers

Head light have low but when using high does not work just on one side drivers side


HELP! headlight not working even after change - Nissan Forums ...

www.nissanclub.com/...nissan.../302674-help-headlight-not-working-eve...

Apr 1, 2010 - 13 posts - ‎6 authors
My passenger side low beam headlight recently went off on me. ... I've changed the bulb again, and changed the fuse just in case, but .... My driver side headlight wire got loose so when i hit a bump at night if would flicker. ... When you notice one side not working (Low or High beam) it could be the module. Headlight replacement
15 posts
Jan 22, 2009
Low beams don't work but High's do
8 posts
Mar 20, 2005
More results from www.nissanclub.com

Dec 20, 2015 | 2004 Nissan Sentra

2 Answers

What would cause the low beam headlight not to work when all other lights work?


If you have standard halogen bulbs:

  1. Burned out light bulb; or
  2. Fried wires between the dashboard wiring harness and the headlight bulb connectors; or
  3. Fried headlight bulb connectors.
If you have HEI emitters:
  • Failed ballast.

May 11, 2015 | 2002 Mercury Grand Marquis

4 Answers

High beam and low beam not working together.


I think you just need new bulbs in both sides. The High and low beam are in one bulb.

Dec 21, 2014 | 2002 Chevrolet Cavalier Coupe

3 Answers

One low beam head lights will not work, high beam works though


check for a damaged wire for the low beam. Also wouldn't hurt to check the ground wire as the high beam will try and ground through the low beam but not visa verse

Dec 29, 2013 | 1997 Chevrolet Blazer

1 Answer

CHANGED HEADLIGHT ASSEMBLY ON 2002 JEEP LIBERTY ONLY HIGH BEAM LIGHT COME ON


Try flicking the mulit-function switch high beam on and off. There has been known problems with this switch, but mostly the first place to start is with some new light bulbs.
Or possibly your low beam filaments are burnt out. You have to replace the bulbs. Each bulb has a lowbeam and a high beam filament.

Apr 10, 2013 | Jeep Liberty Cars & Trucks

1 Answer

Low beam burnt out


The headlight on an 03 baja are a double element bulb for high an low beam. I replaced mine with 9007 bulb from auto parts store. Be careful to pay attention to bulb position, they can be installed up side down having the high beam as your low beam. I would shine the lights up against a wall or garage door and flip your high and low beams on and off to see how the shine.

Feb 21, 2010 | 2003 Subaru Baja

1 Answer

Headlights not working right


Usually headlights have two filaments in them for low and high beam. One of the fillaments may be broken while the other is still intact which is why the low beam works and the high beam doesn't. The solution is to replace the bulb. This should take care of the problem.

Jan 28, 2009 | 2004 Dodge Ram 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...