Question about Cars & Trucks

1 Answer

I have a 2005 audi a6 3.2, with a NO ignition starting, not lights, no crank and gauges all read in error I think it might be a master relay, where is it and is this common?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 5,433 Answers

No not common! If your battery is fully charged then it will be the main power fuse on the fuse box under hood! Probably 40/50 amp not likely to be a relay!

Posted on Nov 08, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 67 Answers

SOURCE: check gauges light

Possible bad guage, bad wiring, or bad sending unit. Check each one independently of each other, start with wiring first, then sending unit.

Posted on Aug 27, 2008

  • 14 Answers

SOURCE: My 1991 Honda Accord will crank, but not fire.

there is a main relay located under the drivers side dash, you have to first remove the cruise control module to view this relay

Posted on Jul 13, 2009

SOURCE: I have a 2005 Saturn Relay. Everytime we fill-up

Some of these GM's have a seperate fuel guage relay under the dash. Their not cheap. Since you could have anything from a bad sender in the tank to a bad relay its best to leave this to a professional. Next time this happens try smacking the fuel tank a few times hard. If the gauge goes up its most likely a sender in the tank issue. If nothing happens then it really needs to be diagnosed correctly.

Posted on Jul 14, 2009

VAGMatt
  • 31 Answers

SOURCE: Code P0118 on Audi A4 - Related to Ignition Coil Problem?

Hi, the sensor on the engine (right at the rear end of the cylinder head) has two separate outputs. One drives the temperature gauge and the other provides data for the engine control unit. The output for the engine control unit is almost certainly faulty and the sensor will need to be replaced. It isn't an expensive item and's not time consuming to replace (1/2 hr) - so you could ask Audi to do it for you when they replace the ignition coils.
Hope that helps Matt..

Posted on Nov 23, 2009

  • 615 Answers

SOURCE: starter wont crank on a 2000 oldsmobile intrigue

Check your manual if you have it. I believe you need to have the key in the ignition in the ON position for about 10 minutes to reset the security system.

Posted on Jul 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Jeep will crank but no start what can my problem be


well you need to find out if it is spark or fuel giving you the problem check for spark first they have problems with the crankshaft position sensor which could be the problem not easy to get to its bolted to the bell housing with 2 bolts if you do not have spark that would be a good place to start

May 20, 2014 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Car turns over but no gauges turn on not even gauge lights, car won't start, 2003 Pontiac sunfire, could it be ignition relay and where would it be located


Here is what should happen: Turn the key "ON" position, this is called primary circuit. do not start, all your cluster gauges should come on. Now crank it, this is called your secondary circuit if it won't start and your cluster gauges don't work, yes, your problem is your ignition switch other manufacturer calls it relay but works on same principles.

Nov 15, 2013 | Cars & Trucks

2 Answers

Starting problems


check batt terminals or master batt relay under hood

Oct 16, 2013 | Audi Cars & Trucks

1 Answer

2000 jeep wrangler won't start, good crank, no bus


Check fuses first, but could be needs new CPU

Jun 14, 2012 | 2000 Jeep Wrangler

1 Answer

1999 audi a6 wont crank sometimes


Either there is a bad or dirty battery connection which is allowing the lights but no crank or you could have dirty or loose starter wires or starter relay may be bad or ignition is a possibility. All these can be tested with an ohmmeter for power. I would start with connections

Jun 04, 2012 | Audi A6 Cars & Trucks

2 Answers

S10 2.2 5 spd 2wd...electrical problem


Sounds like ur computer. When a computer goes out they seem to go in different ways. Also there should be main circuit relays either under the hood or on driver side dash. If you pop a main relay it will kill all main circuits to protect a circuit melt down. Hope this helps. Thanks Josh

Nov 22, 2009 | 1997 Chevrolet S-10 Pickup

1 Answer

Code P0118 on Audi A4 - Related to Ignition Coil Problem?


Hi, the sensor on the engine (right at the rear end of the cylinder head) has two separate outputs. One drives the temperature gauge and the other provides data for the engine control unit. The output for the engine control unit is almost certainly faulty and the sensor will need to be replaced. It isn't an expensive item and's not time consuming to replace (1/2 hr) - so you could ask Audi to do it for you when they replace the ignition coils.
Hope that helps Matt..

Nov 15, 2009 | 2005 Audi A4

1 Answer

I have a 2005 Saturn Relay. Everytime we fill-up the tank, the gas gauge will stay on empty and the low fuel light will come on. Finally, after about 30 min of driving the gauge will slowly go up and...


Pick up a diagnostics module with reset capabilities, plug it in to the port below the steering column and reset the error codes. This will reset the sending unit and it should read correctly after the rest. I had a similar problem and this inexpensive solution fixed the issue. Saved or $500.00 in repair and diagnostics.

Jul 14, 2009 | 2005 Saturn Relay

5 Answers

2001 jeep cherokee cranks, no start, no bus


I just had the same problem of my 2001 jeep cherokee not starting with no gauges responding and a "no bus" reading. After reading the responses I changed out the CPS and my jeep now runs great! however, it was not as hard as I thought it would be. Very easy with 7/16 bit and a 10inch extender. In and out in less than 5 minutes. Finding it was the hardest part. Blends in with the bell housing. I did this from under the jeep with a good shop light. I paid about $80 for the part here in Atlanta, GA

Jul 29, 2008 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...