Question about Cars & Trucks

Open Question

1991 mack ch613 code 6. 2 what does code mean

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 267 Answers

SOURCE: 01 mack ch613- selected rear turn signal works good, L or R. turn on headlight both rear signals flash, selected is brighter. changed headlight switch no difference.

It sounds to me like a ground wire for one or both of the front turn signals has a bad connection. What happens is that without a ground, the circuit tries to complete through the other lamps.
The other more remote possibility is that the wire that got hot melted to another wire deep in the harness somewhere.

Posted on Jan 30, 2015

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the tps on a 1991 tracker? the one i bought has 4 wires the one on the tracker has 6 wires


the 1991 G16a has a pig tail connector, must have 4 wires.
and shares the Injector connector (tricky pin pulls, and all)
that connector you gander is the injector /TPS connector
it has 6 pins but only 4 are for TPS. (yellow /.red are injector)
see page 3 below, for what all this means. last link below.


try to keep in mind, your car has a VIN engine code U (not 6) code 6 , has no pig tail, TPS.
GM uses U code to say, engine is 8valves, TBI, G16a , my guess, (no photos) is your bought TPS is
with tails, and is correct for your 8v engine.

Install, (need feeler gauges to do it)
it's not just thrown on to the car, it must be calibrated.
or the idle switch WILL fail.(and more)
one maker of this TPS is here: (hard to find)
SMP makes one. sMP #TH-147 is for 8V tbi.

http://www.fixkick.com/buy-parts.html#TPS
do not use 16valve parts on your car.

here is the calibration steps.
http://www.fixkick.com/sensors/tests/TPS-testing.html#8v_FSM_cal

the factory page is here
http://www.fixkick.com/TPS/TPS-p91.JPG

http://www.fixkick.com/TPS/TPS-p92.jpg

and page 3 here
http://www.fixkick.com/TPS/TPS-p93.JPG

the last page shows the tricky pin pulls....


you must pull the old pins.' one by one.
then put in then new TPS pins , in the same places of old
matching COLORS.
then do the calibration steps above, using feeler gauges.
same basic steps, from 1989 to 1998.
in 1999 they calibrate it to 0.5vdc, only.
later years, it auto-calibrates.
if the new TPS fails to cure the problem
post the symptoms, and win.

Jun 17, 2016 | 1991 Geo Tracker

1 Answer

2000 Mack truck. ABS light is on and I have two codes 51, 34. Can you tell me what they mean?


Dont hav code sheet but napa can xplain. Probly related to brakes. Always keep fluid clean n clear in antiloc system or u can ruin the module which cost thousands

Jan 06, 2016 | Cars & Trucks

1 Answer

01 mack ch613- selected rear turn signal works good, L or R. turn on headlight both rear signals flash, selected is brighter. changed headlight switch no difference.


It sounds to me like a ground wire for one or both of the front turn signals has a bad connection. What happens is that without a ground, the circuit tries to complete through the other lamps.
The other more remote possibility is that the wire that got hot melted to another wire deep in the harness somewhere.

Jan 30, 2015 | Cars & Trucks

1 Answer

I have a mack ch613 with a e7 350 hp it cuts out in 9th and 10 th gear at 1500 rpm and electrical malfunchtion light comes on its only when Im at 1500 rpm


check for a faulty selector position switch on the 9-10 gear selection If there is a connection that is faulty (sensor) it may be cutting out the engine to prevent over-revving it. From your description it is a specific fault and switches/wires/connections appear to be the problem

Nov 01, 2014 | Cars & Trucks

1 Answer

How to Install a new eaton 2104-20892561 clutch on a Mack Ch613


It\'s the same for all CH models and then some ,do you have the old one out ? I will look for you, I have done a lot of them ,I\'m going to ask a few questions so bear with me , ok ? ,do you have a pilot shaft or can borrow one ? for aling clutch ,and a big tranny jack , did you remove or have motor out or are you just removing tranny. ? it\'s all just really heavy it\'s a 2 person job no dough, but for the most part same as a car or truck, OTC makes a clutch installing tool to hold the two clutch plates and two pressure plates , hard part is putting throw out bearing in and holding clutch lever all the way back so it can fall in and don\'t forget to put clutch brake on shaft, if using 1 piece unit, aftermarket ones break down to easy (crap) but you can put it in after an adjust it when adjusting clutch for first time .hope this gets you going ,get back to me and I\'ll do my best to get info for you or a place for you to get it hope this helped .

Woody

Sep 01, 2014 | Cars & Trucks

2 Answers

WHAT DOES THE LIGHTNING BOLT WARNING LIGHT MEAN ON A 2006 MACK GRANITE


if you have cold weather its a tire pressure code that may take days to go away

Jul 15, 2014 | 2007 Dodge Caliber SXT Sport Hatchback

1 Answer

What code 44 on a plymouth sundance 1991


Generally speaking, code 12 means the battery has been disconnected at some point in time.
Code 44 means the battery temp sensor circuit is out of normal range, too high or too low.

Oct 03, 2012 | 1988 Plymouth Sundance

2 Answers

What does it mean:Fuel 44 Fail in the VCM in a jaguar 1991 xj6 sovereign?


Code 44 means that the oxygen sensor is signaling the computer that the fuel mixture is bad - too rich or too lean.

Apr 09, 2010 | 1993 Jaguar XJ6

1 Answer

Where is the timing marks on a 1991 geo pirzm? also what is the firing order?


97488ae.gif
1.6L SOHC (VIN Code 4) EngineEngine Firing Order 1-3-4-2Distributor Rotation: Counterclockwise

0be98bd.gif
1.6L DOHC (All 1988 & 1991-92 VIN Code 5)Engine Firing Order 1-3-4-2Distributor Rotation: Clockwise

eabc610.gif
1.6L DOHC (1990 VIN Code 5, 1989-93 VIN Code 6 & 1993 VIN Code 8)Engine Firing Order 1-3-4-2Distributor Rotation: Clockwise


ec1d0cd.gif

Dec 01, 2009 | 1991 Geo Prizm

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...