Question about Cars & Trucks

Open Question

Schematic for 9078

Need teardown schematic to re-assemble 9078 rechargeable screwdriver, Thx Don

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change side turn signal bilb on a VW jetta GLS


There are two spring clams that hold the assembly into the fender, and these are at either side of the assembly, there is usually a screwdriver slot near either side. Gently pry the assembly out, and remove the lens and back, the bulb sits in the twist assembly in the lens. Replace bulb with a clean hand, so that oil and dirt don't get on the bulb surface, pull bulb straight out from socket, and replace by inserting bulb back in socket. Voila. Replaced Turn Signal Fender light.

Mar 25, 2012 | Cars & Trucks

1 Answer

I need to change the heater core in a 2004 Chevy Malibu Classic and can't find schematics or directions. I can't afford labor charges. Where can I get info to help me?


the best is to go to any auto parts store to buy a haynes manual for your car . they are based on a complete teardown of vehicle. for about 25.00 dollars. this book will show how its done. there are too many steps to mention. good-luck! toolman,

Sep 15, 2011 | 2004 Chevrolet Malibu

1 Answer

How to replace brake light in 2009 Nissan Sentra


  • For this car to change the brake light you have to remove the taillight assembly. It's not to hard. Follow these steps.

  1. Open the trunk.
  2. Look some plastic hook/clamps.
  3. Pop the center up with a screwdriver and then pull the entire piece out.
  4. Pull the carpet back for the tail light you are replacing.
  5. Now you will see two 10mm nuts and a wire connector.
  6. Remove the nuts, and just pull the connector away from the assembly a bit. You don't need to disconnect.
  7. Now pull your light assembly forward.
  8. Now twist the light to the left a bit and pull the light out of the assembly.
  9. Now pull the bulb strait out of it's socket.
  10. Insert new light.
  11. Reverse steps to finish the job.

  • Hope this helps and thank you for using FixYa.

Regards, Tony

Aug 10, 2011 | 2009 Nissan Sentra

2 Answers

How can I replace the left front fog light unit from a toyota prius from 2009. I cann't find a maintenance manual for this model and year.


Its all attached by clips and screws.Nothing much special.But its all about the procedure.Dont forget the mark the position , location of the screws you remove, so while refitting you don't face any problemTo replace fog light bulb or to replace replace complete fog light unit, click this link below:--- http://technoanswers.blogspot.com/2011/07/how-to-replace-left-front-fog-light.html ---------- This will help.Thanks.Helpmech.

Jul 09, 2011 | Toyota Prius Cars & Trucks

2 Answers

I need a free schematic of the rear brake assembly on a 2004 Ford Ranger. I fixed the brake cylendar but can't remember where one part goes


that is why you never remove both sides at the same time, that way if you forget something you can go look at the other side.


johnjnail_27.jpg

johnjnail_28.jpg

May 14, 2011 | Ford Ranger Cars & Trucks

1 Answer

Replacing a turn signal bulb....Baffled...Thanks


Hello,

Please do not be baffled. To replace the turn signal bulb on Your car is quite simple, all You need to do is to get a screwdriver and follow the steps below:
  1. Open the hood and locate the mounting screws for the outboard marker-light assembly just above the light. Remove the screws with a Phillips screwdriver, then remove the assembly, setting it aside for now.
  2. Locate the two mounting screws on top of the turn-signal light assembly under the side-marker lens. Remove the two screws with a Phillips screwdriver, then set the screws aside. Slide the turn signal out and locate the socket on the back of the assembly.
  3. Rotate the bulb socket counterclockwise and pull the socket out of the assembly. Pull the bulb straight out of the socket and discard it. Install a new bulb into the socket, pushing it in until is seats. Position the socket back into the rear of the light assembly, turn it clockwise to lock it in place, then slide the assembly back into the front of the Jeep.
  4. Install the mounting bolts that secure the turn-signal light assembly, tightening the screws with a Phillips-head screwdriver. Position the side marker-light assembly to the side of the Jeep and install the retaining bolts.
  5. Tighten the retaining bolts for the side-marker lights with a Phillips screwdriver, then close the hood. Test the repair by turning the lights on and visually verify that the light is working..
Hope this helped. Thank You for using FixYa!!!

Jan 28, 2011 | 1998 Jeep Grand Cherokee

1 Answer

D16Y7 engine schematic / teardown and rebuild manual


You need to purchase service manual. Check with local auto parts stores and/or order online from Amazon.com

Jan 08, 2011 | Honda Civic Cars & Trucks

1 Answer

Right rear shoe brake assembly on a 1993 cadillac deville---i need to see a schematic to see howv parts are assembled because all parts are missing---i need to know what to buy and then how to assemble,...


buy the "rear brake hardware kit" for your vehicle; it will have all the parts for 1 wheel, typically both wheels are done at the same time.i recommend buying the haynes manual specific to your type vehicle, it will have easy to follow step by step instructions.otherwise you can remove the drum from the other side of the car and take a picture of the hardware setup to use as a reference

Nov 18, 2009 | 1993 Cadillac DeVille

1 Answer

2000 Ford Escort - recharge port for AC


The low pressure service gauge port valve is located on the A/C manifold and tube. please rate, thx

77a249a.gif

Jul 07, 2009 | 1997 Ford Taurus

2 Answers

How do i change the rear tail light lens on my 2008 hyundai veracruz


Open the rear hatch. Using a small straight edge screwdriver, insert the screwdriver into the slot at the top of each of the two screwcovers on the inside lip of the tail light assemby and carefull pry open. Remove the two screws using a philips screwdriver. Drape a small cloth over the head of a larger straight edge screwdriver and insert at the tip of the tail light assembly (on the rear side of the car and carefully turn back and forth while wiggling the entire assembly. This will eventually allow you to work the tail light assembly loose from the grip pin that is holding the assembly on. Once removed, replace the appropriate bulb. With the assembly still not installed, have someone step on the brake to ensure the new bulb is working properly. Reinstall assembly. Hope this was helpful....I just changed mine.

Jun 12, 2009 | 2007 Hyundai Veracruz SE

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...