Question about 2008 Ford Fusion

1 Answer

I just bought a 2008 Ford Fusion and the light with the wrench is on. I checked owners book and it's something with the transmission or throttle. The dealership connected it to the machine and their

I just bought a 2008 Ford Fusion and the light with the wrench is on. I checked owners book and it's something with the transmission or throttle. The dealership connected it to the machine and their werent any codes. Should I be worried?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Ford Master
  • 45,139 Answers

If the Ford dealer could not diagnose the problem without pulling a DTC, you need to find a Ford dealer experienced enough to fix the problem without a code.

Posted on Nov 07, 2014


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: throttle does not work-wrench light on

I need to know if the TPS in my 2006 Ford Fusion SEL, can be replaced on my own, or does it need to go to a dealer to be replaced?

Posted on Apr 30, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2007 Ford Fusion. ABS Light, Wrench light, and Traction Control light are all stuck on. What does this mean?

It means you have a Anti-lock brake problem an DTC'S - diagnostic trouble codes are set in the EBCM - electronic brake control module or could be a Transmission problem or the electronic throttle control problem . Having these code's checked would be a good first step . The dealer or someother qualified repair shop .

Mar 17, 2017 | Ford Cars & Trucks

1 Answer

2008 ford fusion all of the sudden start idling rough when I start it at the same time it will not shift into overdrive on highway and cruise control stopped working. Also the wrench light came on.

With the wrench light on ,DTC'S - diagnostic trouble codes are stored in the module's . This indicates there is a problem with the transmission or the electronic throttle control . Have it checked for DTC'S

Jan 09, 2017 | Ford Cars & Trucks

1 Answer

I have a Ford F-150 xlt 4.6 with a p0401 code.

code p 0401 refers to exhaust gas recirculation (EGR) system---insufficient flow detected==== causes ---hose leak/blockage, basic setting not carried our (if applicable)---wiring---EGR valve ---EGR solenoid ---ECM
when you have done everything make sure that you use a scan tool to reset the ECM
Items that you haven't mentioned are wiring and substituting the ecm with a known operational one
bad wiring and connections / ground , broken in side the insulation may cause the problem as well

Sep 25, 2016 | Ford F-150 Cars & Trucks

1 Answer

Engine idl, at the moment is 1000 revs plus, should be below this. Vehicle is Ford Fusion 1400 and the year is 2008.

Your fusion has electronic throttle control , drive by wire etc. Is the check engine light lit ? Could have a gummed up throttle plate . Videos on youtube on cleaning .

Jul 13, 2016 | Ford Fusion Cars & Trucks

1 Answer

It wont idle and numerous codes after trans rebuild that werent there before rebuild

Computr probly not recignizn the newtrans and electrics. May needit flashd or programd again. An xperiencd shop that can read data...not a dealer

Feb 25, 2016 | 2006 Mercury Mountaineer

1 Answer

Need to know what code 2110 ford fusion 2006 se

P2110 2006 FORD FUSION P2110 2006 FORD FUSION - Throttle Actuator Control System - Forced Limited RPM 0 Comments ' Add Yours Possible causes - Faulty Throttle Actuator Control (TAC)
- Throttle Actuator Control (TAC) harness is open or shorted
- Throttle Actuator Control (TAC) circuit poor electrical connection help.png Help with this Symptoms - Engine Light ON (or Service Engine Soon Warning Light P2110 2006 FORD FUSION Description The TAC system is in the failure mode effects management (FMEM) mode of forced limited RPM.

Read more:

Sep 22, 2015 | 2006 Ford Fusion

2 Answers

Mine is a 2011 ram 1500 4x4 5.7 himi started missing this morning and i hade a code ran it came back as cylinder#2 missfire i changed coil pack and plugs it seemed to regain power but still missis...

I just started one of these today. What a pain... 16 plugs, 8 wires and 8 boots. Replace them all. It is time..Most likely, the wires and boots are burnt threw. Just like the one I'm doing. Plus the plugs are worn out..

Jan 06, 2015 | 2011 Dodge Ram Pickup 1500

2 Answers

How do i fix... wrench light ford fusion 2006

You never need to top off fluids

If you do- you have a leak to be repaired

Check the vehicles systems for codes,
then google those codes to see the problem

TYPE: OBD & your code

It is going into ETC Failsafe or something

Do not use it at all,you may have converter ruining
cylinder misfires, from bad ignition coils

You add NO WATER to any vehicle

Distilled water & coolant only

Aug 25, 2014 | 2006 Ford Fusion

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

480 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides