Question about Cars & Trucks

1 Answer

I failed my warrant because reverse lights were not working. The mechanic said it didn't have a reverse sensor on the gearbox , but been a auto where would the sensor be?? Help

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

You souldnt need any back up lights to pass inspection. You could also have bad bulds or even wiring problem. And i have a question for you auto or manny transmission

Posted on Nov 07, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: gear box

i have a polo 1.4 it heats up lower pipe remains cold why

Posted on Jul 03, 2008

SOURCE: gearbox sensor

dear friend:both the sensors is on top of the gearbox one in the middle and the other closer
to the fire wall.

Posted on Sep 19, 2009

  • 1986 Answers

SOURCE: NO REVERSE LIGHTS REAR PARK SENSOR WHEN REVERSE SELECTED

On the side of your transmission will be a switch with several wires coming out of it. This is your reverse switch that turns on your reverse lights and most likely needs to be replaced. The switch is just plug and play

Posted on Oct 01, 2009

wcbotha
  • 92 Answers

SOURCE: kia sportage gearbox mechanism that operate the

The gear lever engage the switch remove console around lever to get to switch. Ensure fuses are OK and bulbs is OK before go to removing console. Enjou from Willem SA

Posted on May 06, 2010

emissionwiz
  • 76070 Answers

SOURCE: Auto gearbox gets stuck in reverse gear.

This is likely a sticking valve in the transmission valve body assembly, try adding a can of Lucas brand transmission additive.

Posted on Jun 14, 2012

Testimonial: "Hi Dennis. Thanks for your solution have ordered parts to drain gearbox oil and replace filter in the sump, will add additive when I put it back. Thanks for your reply."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mechanics advised that gearbox needs replace after diagnostic Of codes . Dash light still on after codes being read , have had ecu replaced 2yrs ago ? What do you think it could be , thanks phil


didnt specify vehicle --generic answer--until repair is made the vehicle will show engine light and have codes --if gearbox is problem for limp mode /until repairs are made or gearbox replaced you will be in limp mode --and as to sensor find out what one it was --start problem may show back up if sensor was problem --and GET a 3rd opinion you have 2 mechanics with different opinions on your problem and i guess they are reading your trouble codes differently

Sep 20, 2016 | Cars & Trucks

1 Answer

I have a Nissan Serena 2003 model with CVT gearbox. It wount engage 1,2 when moving in low speed, or uphill.when behaving this way, its fails to reverse,or reverse in difficulty.


Have the codes read at Autozone. Check out the wiring to the speed sensor on the output shaft of the gearbox. Be prepared to change the speed sensor itself. Is the speedo functioning? Often when the speed sensor is faulty the speedo dial fails

Aug 23, 2016 | Nissan Cars & Trucks

1 Answer

Tach problems


A broken wire connection on the Tach connector to the gearbox. The ABS sensor on the hubs are out of line after a new pad/rotor brake change. Cable broken. Fuse blown in main dash fuse box. Gearbox change over recently, bad mechanic didn;t replace the sender.

Jun 01, 2014 | 2000 Volkswagen Beetle

1 Answer

I was trying to reverse from a down hill position. But putting the shift on reverse didn't work. The car kept driving forward. It beat the out of me cause I was blocking access to a lot of cars behind...


I would be checking the oil level in the gear box as if it is low there may be a oil pressure problem that is not locking up the band and clutch to make reverse work. have a pressure test done on the gearbox to check for internal problems. IT is possible that the oil pick up was out of the oil and the box pump was not working

Aug 31, 2013 | 2002 Nissan Pathfinder

1 Answer

Cant find reversing sensor


if manual it will screw into the gearbox at the reverse slide area Possibely the only unit there. If auto sometimes they are near the selector on the box

Jan 13, 2013 | Hyundai Cars & Trucks

1 Answer

Reverse lights not working bulbs are good sockets are good


check the switch on the gearbox ,manual or auto it will have a reverse light switch with two wires running to it on the gearbox somewhere

Jun 05, 2011 | 1988 Nissan Pathfinder

2 Answers

Reverse lights will not light up on mazda 6. New fuse and bulbs were put in. What to try next?


need to check the reverse switch at the gearbox. there has 2 wire to the sensor.

Nov 20, 2010 | 1999 Mazda 626

2 Answers

Reverse lights are not working on Chrysler Grand Voyager 2.3 CRD


There has to be a switch , They do not work from ESP , its either going to be on the gearbox case or connected with the gearshift lever/mechanism.
If this is automatic transmiision, then it would be the inhibitor switch fitted to the selector mechanism.
Hope this helps

Dec 10, 2009 | 2003 Chrysler Voyager

1 Answer

Reversing lights not work


sounds like it could just be the reverse sensor located on the acctual gearbox under bonnet, you can tell which one it is as it is one of possible two.

Feb 24, 2009 | 2002 Mitsubishi Montero Sport

1 Answer

Reverse Lights not working and engine starts on any gear


You have a reverse indicator switch on you transmission. You will need to make sure that it didn’t come unplugged or that the wire didn’t break. This is a single wire that should be close to the rear of the transmission.

Jul 05, 2008 | Mercedes-Benz E320 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...