Question about Cars & Trucks

1 Answer

I Have a huge problem with a 2002 dodge intrepid... every sensor except the 02 sensors have checked out good,ohms test came out positive. Injectors good,very rich fuel. Fuel regulator is good,pump good. Everything shows up good,even timing marks. All good,but won't start because fuel is too rich...HELP

Posted by on

  • CPR Solutions Nov 16, 2014

    Without a scan tool, there is very little you can check at this point. If you have one, check to see what voltage you throttle position and MAP sensors are reading. If not, you can check them with a voltmeter. While cranking, both sensors should read about 1 volt with the throttle closed. Also, check to make sure you have 5 volts getting to each sensor.



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.


    An expert who has answered 20 questions.

  • Expert
  • 78 Answers

Does the car try to start at all?
What engine is it? Is it really too much fuel or is there an ignition problem? More information is needed here.
Also, what is cranking vacuum reading?

Posted on Nov 07, 2014

Testimonial: "engine is a 2.7 and yeah it kicks over then dies. found a couple vacuum leaks,the thing is plugs come out soaked and black soot on them."

  • 1 more comment 
  • Leroy Brodian
    Leroy Brodian Nov 08, 2014

    piston compresion is 150 psi in all cyleners,crank and cam sensor new...

  • Leroy Brodian
    Leroy Brodian Nov 11, 2014

    the car won't start at all. it will try but can't.

  • Leroy Brodian
    Leroy Brodian Nov 12, 2014

    fuel injectors are spraying very good,still no run



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

02 caravan will start and stay running as long as my foot is on the gas but as soon as i take my foot off the gas it dies

using a digital volt ohm meter test the throttle position sensor. if it has a dead spot at idle position it will stall. also if the throttle plate is dirty it can cause a stall at idle and all you have to do is clean it.

Jun 12, 2015 | 2002 Dodge Caravan

1 Answer

I have a 2002 Intrepid with P 0340 code showing. Jusst started today. No stalling, rough running, or misfiring. Just curious is the camshaft position sensor could be thrown off by the timing belt being...

It could be both. Being a 2002 it could be the timing belt or just the sensor being bad and reporting the wrong position to the computer. Do a compression check first to see if your losing compression. If you aren't then it most likely is the Cam position sensor or Crank Position sensor. That code indicates it is the Cam Position Sensor that is faulty which is a good thing because that is easier to get at and replace.

Aug 25, 2011 | 2002 Dodge Intrepid

1 Answer

Code p0152


Dec 11, 2010 | 2002 Dodge Intrepid

1 Answer

Number of 02 sensors in a 2002 intrepid 2.7

4, 1 on each side before and after the catalytic coverter.If your getting a code on #2 sensor on either
side, this could mean the cat/c is plugging up on that side.

Mar 01, 2010 | 2002 Dodge Intrepid

1 Answer

O2 sensors

If you dont have a heater code then the ohms are correct. Usually around 15 or so. Bad 02 heater sensor if either 0 which is shorted internally or infinity or open which is like a popped lightbulb. The fuel control side should be open, infinity. If you have a code that says stuck lean or rich or slow to respond then you most likely have an engine or otther sensor issue

Jan 17, 2010 | 2000 Dodge Intrepid

1 Answer

2002 Dodge Intepid engine change now it wont start

how long ago did dealer do the job, if recently I think they should feel some obligation to assist you.

Dec 04, 2008 | 2002 Dodge Intrepid

3 Answers

02 intrepid ticking

Most dodge motors have adjusters on the rockers for taking up slack in the valve-train. when these get worn or plugged by dirt they turn the valves from soft hydraulic to hard ticking due to a space between the lifter and the valve. If this is an overhead cam with roller lifters then these have become worn or fouled.

Sep 30, 2008 | 2002 Dodge Intrepid

3 Answers

95 intrepid running rough??

possibly the EGR valve or EGR solenoid. it regulates the fuel intake

Aug 16, 2008 | 1995 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

80263 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15139 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides