Question about Cars & Trucks

1 Answer

No ignition fire 97 5.9 3/4 dodge van replaced coil,crank sensor,fuelpump,module in dist help

Just turns over wont start was running great turn it off and it never started again

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 78 Answers

Are any trouble codes stored? Is there power to the ASD relay? You likely have a blown fusible link or corroded terminal under the fuse box.

Posted on Nov 07, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
shanat
  • 359 Answers

SOURCE: 1991 jeep wrangler cranks but wont start

just a suggestion hows your leads?

Posted on May 24, 2008

  • 201 Answers

SOURCE: 1992 dodge 318 engine turns over, but no start. No

if truck has a ceramic ballist resistor near and connected to coil this could be problem or the crk posistion sensor could be too, i would change ballast first if you have on your truck appx cost $10

Posted on May 09, 2009

  • 154 Answers

SOURCE: 1990 jeep cherokee cranks but wont start I've

check fuses

Posted on Jun 19, 2009

ourhowse
  • 2007 Answers

SOURCE: 97 dodge intrepid just all of sudden stopped firing

Try mass air flow sensor.

Posted on Jul 01, 2009

  • 412 Answers

SOURCE: 97 dodge neon died replaced parts and still no spark HELP.

YOU NEED TO CHECK DARK GREEN/ORANGE WIRE AT IGNITION COIL WHEN CRANKING ENGINE FOR POWER..IF NO POWER,SHUTDOWN RELAY IS NOT BEING ENERGIZED..THIS ENGINE ALSO HAS CAMSHAFT POSITION SENSOR ON END OF CYLINDER HEAD..ENGINE CONTROLLER NEEDS CAM AND CRANK SIGNALS TO ENERGIZE THE SHUTDOWN RELAY..UNPLUG CRANK SENSOR AND CHECK VOLTAGE ON ORANGE WIRE..SHOULD HAVE APPROX 8V..IF NOT..UNPLUG CAM SENSOR AND SEE IF 8V SUPPLY RETURNS..IF NO POWER TRY UNPLUGGING VEHICLE SPEED SENSOR LOCATED IN TRANS HOUSING WHERE RIGHT SIDE AXLE COMES OUT OF TRANS..IF 8V RETURNS..THE SPEED SENSOR IS SHORTED INTERNALLY..THESE 3 SENSORS SHARE THE SAME 8V SUPPLY CIRCUIT..WITH SPEED SENSOR UNPLUGGED,PLUG CRANK SENSOR BACK IN AND TRY TO START ENGINE..HAVE SEEN THIS SAME PROBLEM AT WORK RECENTLY

Posted on Jul 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Engine turns over but wont start. You can hear thr fuel pump come on. Is it electrical? Could it be battery, fuse, or loose wire?


This sounds like the crank shaft sensor is bad. The sensor sends a signal to the computer about when to fire the coils for spark.

May 02, 2015 | 1999 Dodge Durango

1 Answer

Dodge ram van wont start


Check fuel pump,and fuel pump relay. Alot of newer vehichles have a fail-safe mode that wont let ignition spark, if no fuel pressure is present, or vice versa.

Mar 05, 2014 | Cars & Trucks

1 Answer

97 dodge ram van 5.9 litter cranks over and over but no start no spark


First thing to check is the ASD relay and voltage at the coil.

Aug 25, 2012 | 1997 Dodge Ram 2500 Club Cab

5 Answers

Truck wont crank. we have put new distributor cap, rotor button, coil pack, plugs, wires, and fuel pump. we also checked our firing order.


you said you repl dist cap that means you don't have a crank sensor you have electronic ing module. remove your elec ing module have it tested most auto parts stores could test your module, or check your coil at the neg terminal. should have power. if not you lost your primary volt from your batt.your secondary power is coming from your electronic ing module from the module to the pos terminal on the coil, when the eng cranks,from the coil to the dist cap , from the dist cap center to the rotor then out to the plugs,this all happen pervided the timing belt or timing chain is ok. the cumbustion chainber needs 3 things , thats fuel, air, and spark.

Apr 17, 2011 | 1996 Chevrolet K1500

3 Answers

2005 gmc safari wont start checked coil spark


how much fuel pressure you have when turn key on

Feb 04, 2010 | 2005 GMC Safari

2 Answers

97 dodge neon died replaced parts and still no spark HELP.


YOU NEED TO CHECK DARK GREEN/ORANGE WIRE AT IGNITION COIL WHEN CRANKING ENGINE FOR POWER..IF NO POWER,SHUTDOWN RELAY IS NOT BEING ENERGIZED..THIS ENGINE ALSO HAS CAMSHAFT POSITION SENSOR ON END OF CYLINDER HEAD..ENGINE CONTROLLER NEEDS CAM AND CRANK SIGNALS TO ENERGIZE THE SHUTDOWN RELAY..UNPLUG CRANK SENSOR AND CHECK VOLTAGE ON ORANGE WIRE..SHOULD HAVE APPROX 8V..IF NOT..UNPLUG CAM SENSOR AND SEE IF 8V SUPPLY RETURNS..IF NO POWER TRY UNPLUGGING VEHICLE SPEED SENSOR LOCATED IN TRANS HOUSING WHERE RIGHT SIDE AXLE COMES OUT OF TRANS..IF 8V RETURNS..THE SPEED SENSOR IS SHORTED INTERNALLY..THESE 3 SENSORS SHARE THE SAME 8V SUPPLY CIRCUIT..WITH SPEED SENSOR UNPLUGGED,PLUG CRANK SENSOR BACK IN AND TRY TO START ENGINE..HAVE SEEN THIS SAME PROBLEM AT WORK RECENTLY

Jul 18, 2009 | 1997 Dodge Neon

1 Answer

No fire, Won't Start


immobilizer , crank and cam position sensors have not being mentioned
dodge code 32 refers to faulty EGR and not to ignition problems
also if the ignition switch is faulty there will be no run circuit to provide power for the ignition in the run position

Nov 14, 2017 | 1995 Dodge Ram

3 Answers

1992 dodge 318 engine turns over, but no start. No spark present. Replaced ignition coil and pickup coil, still no spark. 1992 dodge ram 150 full size truck 318 engine. starts sometimes then wont start...


if truck has a ceramic ballist resistor near and connected to coil this could be problem or the crk posistion sensor could be too, i would change ballast first if you have on your truck appx cost $10

May 09, 2009 | 1992 Dodge Ram 150 Club Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

78257 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14405 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...