Question about 2010 Dodge Ram Pickup 1500

1 Answer

How Do I replace a blend air door for a 2010 Dodge Ram

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 13,081 Answers

You may have to pull the dash or glove box to get at it. Your best bet is to go to www.alldata.com for DIYer and get a subscription for your vehicle. about $16.00 for a year. It will show you how to do it and anything else you may want to do.

Posted on Nov 06, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On my 2010 dodge caliber once i remove section of dash to replace the door blend actuator is it visible or do i have to remove anything else?. Ronald mcgough.


I don't have a manual for your model, but did find a YouTube video for a 2008 Dodge Avenger showing the location of a couple of actuators on the HVAC box. It may not be exactly the same for your car, but it should give you an idea of what you're looking for.
There are a few more videos for Dodges, but mostly for Rams (pickups).
2008 dodge avenger blend air actuator location

Nov 22, 2016 | 2010 Dodge Caliber

1 Answer

I have 2001 dodge ram 1500 3.9 my air worked fine till I dropped dash and changwd heater core now no air just heat is that blend soor or control knobs?


Sounds like you may have forgotten to plug in one of the blend door motors or one of the blend doors has been disturbed and is binding or nor operating properly. Highly unlikely anything to do with the controller on then dash

Apr 25, 2015 | Dodge Cars & Trucks

1 Answer

How do i fix a stuck blend door on 2010 dodge nitro?


I would pull off the blend door actuator and swap it out with a new one. Or another option is to swap it out with one of the other actuators. The blend door actuator is interchangeable with the actuators for the mode-air doors and the recirculation-air door.

Disconnect and isolate the negative battery cable.

If equipped, remove the silencer from below the driver side of the instrument panel.

Disconnect the wire harness connector from the blend door actuator located on the driver side of the air distribution housing.

Remove the two screws that secure the blend door actuator to the actuator mounting bracket and remove the actuator

Feb 17, 2015 | 2010 Dodge Nitro

1 Answer

I replaced all my blend doors on my a/c unit. 2006 dodge ram diesel and it's still blowing warm air instead of cold when a/c is on.


Is the compressor engaging under the hood? What are the pressures? Have this checked first and make sure the blend door works that you installed.

Jul 09, 2012 | 2006 Dodge Ram 2500

1 Answer

2010 nitro dodge front vent not blowing air


Blend air door inop, either from vacuum leak, bad check valve or bad actuator.

Jul 07, 2012 | 2010 Dodge Nitro

2 Answers

How to replace a Blend Door Actuator on a 2000 Dodge Ram 2500 Conversion Ram Van? The air blows out the top, but will not blow out the vents.


Blend door mixes hot and cold, not a distribution control. Look for loose or dislodged vac lines... Heater designed to fail in defrost mode.

Sep 06, 2010 | Dodge Ram 2500 Cars & Trucks

1 Answer

2004 Dodge Ram 3500 Turbo Cummins diesel, air conditioning is cold but there is very little air pressure even when turned on high, fan sounds like it is blowing like crazy but very little air movement...


Sounds like the "Blend Doors" are not completely closed (or opened). The Blend Doors open and close to direct the air from the blower motor to the vent selection you have made on the control panel (defrost on windshield, floor, front, etc) You may need to try various selections to see if the blend doors actually open or close. If no changes, it could be a blend door actuator failing.

Aug 05, 2010 | Dodge Ram 3500 Cars & Trucks

1 Answer

I have a 1995 Dodge Ram 1500 V6. When the A/C


if the compressor is cycling the problem is not the fixed orfice, it is very likely the temperature control blend door actuator has failed and the blend door is stuck in the heated air position. .

Sep 16, 2009 | 1995 Dodge Ram

1 Answer

Blend door not working.


The bleed door controls air temp not where it comes out, dash, floor, defroster, this is most likely a mode control switch problem, that switch is on the ac control head.

Sep 23, 2008 | 2001 Dodge Ram 3500 Truck

Not finding what you are looking for?
2010 Dodge Ram Pickup 1500 Logo

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...