How do I remove the left rear wheel bearing?

SOURCE: 1999 mercury sable front wheel bearing

Not too bad. Just remove the Wheel and the Brake Calipers. Then remove the Dust Cap off the Center of the Rotor. Inside there is a Bolt with a Cotter Pin In it. Remove the Cotter Pin and the Bolt. The Rotor will now Slide off the Spindle, The Bearings are Loose and Probably inside the Rotor. Remove these Bearings and get a Tube of High Temp Grease. Put a Big gobb of grease in the Palm of your hand and Roll the Bearing around in your Hand. Be sure to use your Fingers on the Inside of the Bearings to get it in. The same Goes with New Bearings.

SOURCE: rear wheel bearing

SECTION 205-02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Axle Shaft Removal

1. Raise and support the vehicle. For additional information, refer to Section 100-02 .

1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .

1. Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .

1. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.

1. Remove the differential pinion shaft (4211).
   1. Remove the differential pinion shaft lock bolt (4241).
   1. Remove the differential pinion shaft.

1. CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
   Remove the U-washer (4N237).
   1. Push the axle shafts (4234) inboard.
   1. Remove the U-washer.

1. CAUTION: Damage to the rear brake anti-lock sensor (2C190) may occur if it is not removed before the axle shaft.
   Carefully remove the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .

1. CAUTION: Do not damage the wheel bearing oil seal.
   Remove the axle shaft.

1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.

1. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
   Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.

1. Lubricate the new rear wheel bearing with the specified lubricant.

1. Using the special tools, install the new rear wheel bearing.

1. Lubricate the lip of the new wheel bearing oil seal.
   • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.

1. Using the special tools, install the new wheel bearing oil seal.

1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

1. Lubricate the lip of the wheel bearing oil seal
   • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.

1. CAUTION: Do not damage the wheel bearing oil seal.
   Install the two axle shafts.

1. CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
   Install the U-washer.
   1. Position the two U-washers on the button end of the axle shaft.
   1. Pull the axle shaft outward.

1. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 prior to installation.
   Install the differential pinion shaft.
   1. Align the hole in the differential pinion shaft with the case lock bolt hole.
   1. Install a new differential pinion shaft lock bolt.

1. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.

1. Install the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .

1. Install the rear brakes. For additional information, refer to Section 206-04 .

1. Install the tire and wheel assembly. For additional information, refer to Section 204-04 .

1. Lower the vehicle.

SOURCE: can't get left rear axle out to replace bearing

you must remove the cover on the rear end, remove the 5/16" bolt on center carrier, push the pin that the bolt whent through out, thenp push the axle in, a c clip will fall out of the carrier then axle may be removed,

Ray Jones

• 97 Answers
• Posted on Jul 26, 2009

SOURCE: 1994 gmc rear axle removal how to

-Remove tire and brake drum
-put drain pan under axle housing
-remove rear axle housing cover (10 or 12 bolts)
-turn gear untiil the bolt for cross shaft shows and remov e the bolt
-remove the cross shaft.
-push axle in until you can remove "U" clip from axle and axle will pull out,
Remove seal, you need a pulller to remove axle brg.

SOURCE: ford fiesta 1999 rear wheel bearings

yes it is one big nut, however it looks like 4 individual nuts due to the fact that they are a thinly stacked layer or thin nuts held together by what you called the tab washer............only way to replace is to get a new one from ford........

Testimonial: "Thank-you for that, I have ordered a new one from the ford dealers. I just wonder why the 4 nuts were fitted in the first place? thank you"