Question about 1987 Porsche 944

1 Answer

Clutch petal won't come all the way up. Now i've adjusted myself out of use

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 404 Answers

Have you checked the slave cylinder

Posted on Jul 04, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Www youtube com activate

If it is a cable clutch operation the adjustment should be at the clutch throw out arm . If it is hydraulic the replace the clutch master cylinder as you may have a blocked compensating port in the cylinder which keeps pressure on the clutch arm and will slip the clutch

Dec 19, 2013 | 1997 Volkswagen Golf

2 Answers

How to adjust clutch cable 90 geo storm gsi

set it for 1/8 inch free play at the clutch lever, at the BELL.

Sep 15, 2013 | Geo Storm Cars & Trucks

1 Answer

Clutch adjustment on 1995 gmc 1500

Sorry iam a europeon mechanic with no knowledge of this model but if i knew if it was hydraulic or a manual clutch then this would give me a better idea but if no play then its over adjusted causing the clutch to ride a bit hence the noise but how the adjuster works i have no idea here

Dec 31, 2012 | 1995 GMC Sierra C1500

1 Answer

How to adjust the clutch cable on a standard transmission

If you can adjust it (in most cases you cannot), you adjust it so that your petal is does not have 'freeplay' after depressing the petal about 1 to 1 1/2"-if after you adjust it and it will not allow clean disengagement (or it slip when you drive and accelerate at higher gears) your clutch is going bad.

Sep 12, 2011 | 1993 Plymouth Voyager

1 Answer

Cant select 1st gear and if i force it in the car rolls forward like automatic. i have adjusted the pedal and was good for 3 weeks now same problem and no more adjustment? clutch is only 40,000 old

the problem isnt your clutch pedal its either your gear box or your engin revs are to high try putting it in gear using the clutch petal but while thecar is off

Jul 04, 2011 | 1992 Toyota Pickup

2 Answers

The clutch is not engaging correctly- if you let clutch petal up, it slips (if you give gas it's worse). If no or little gas given, clutch slowly engages after the clutch petal is all the way up.

sounds like you may be able to adjust the clutch and correct the problem, look at the clutch cable and and adjust it some and see if it helps, if it does then adjust it til you feel it is right.

Oct 13, 2010 | 1985 Honda Civic

1 Answer

Clutch will not engage, when you force it , you can hear it spinning or whatever. when you turn off engine it shifts great. please advise how to adjust clutch petal, it is low or soft, EMERGENCY PLEASE

Replace your Clutch, Hydraulic Clutch System can't be Adjusted but check if oil level is good if not add the missing oil ( With DOT-3 Brake Oil ) try by bleeding it if nothing changed, your clutch need's to be Replaced !

Aug 10, 2010 | 1997 Mitsubishi Mirage

1 Answer

Shifting problems

If its a cable clutch adjust it by tighten it.If its hydraulic then the pressure plate is week change the clutch assembly

Jun 12, 2009 | 1990 Honda Civic

2 Answers

89 ranger manual trans slipping already replace clutch and slave cylinder? still slipping any help?

Manual transmissions do not slip ie. when the gears mesh, there is no slip unless they strip out and make an awful noise and will not pull henceforth.

You probably still have a slipping clutch plate against the flywheel. You need to adjust the clutch petal linkage shaft to allow the pressure plate to be release from the thrust bearing, ie shorten the shaft length.. If you and most likely you do just have the clutch release slave cylinder that releases the clutch when you apply the petal. You need to bleed the slave cylinder of any excess fluid or air that may have entered the line if you opened it at any point. You need to bleed it as you would a break cylinder and this should fix ya.
good luck.
good luck

Jan 05, 2009 | 1989 Ford Ranger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Porsche Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

918 Answers


Level 3 Expert

80417 Answers

Are you a Porsche Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides