Question about 2003 GMC Sierra

1 Answer

I CAN'T GEET THE REAR BREAKS TO BLEED ON THE BACK OF MY 2003 GMC SIERRA Z-71

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,486 Answers

Check duel curcuit valve

Posted on Jul 04, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instructions on how to replace front breaks


remove wheels undo anchor bolts for calipers push out pads Ensure you note where anti rattle springs/plates are located use a suitable clamp press piston back into housing after opening bleed screw to allow fluid to escape to allow piston to move back. Fit new pads and replace calpiers anchor bolts. You will need to do both sides of the car or braking problems will occur. Pump brakes to move pistons out to touch the discs.

Jun 08, 2013 | 1993 GMC Sierra K1500

1 Answer

Radio problems


try speaker on other side as test part if still not working trace wire for breaks if ok rt channel in audio unit out and needs replaced.

Aug 01, 2012 | 2003 GMC Sierra 2500HD

1 Answer

How do you bleed the abs controller on my 2003 Gmc sierria 4WD 5.3L


i usually bleed them by taking it out to a gravel or dirt road and doing about 10 - 20 skidding stops that activate the abs motor and it pumps the air out by itself.

Mar 06, 2011 | 2003 GMC Sierra 1500

1 Answer

How to replace knock sensor on a gmc sierra Z-71 5.3l engine


I think they are in the block, under the intake manifold, there will be 2, replace the harness also.

Dec 03, 2010 | 2003 GMC Sierra 1500

3 Answers

Wiring diagram for 1996 gmc sierra brake asembly


The brake light switch is at fault. Get a new one and replace it. The location is at the brake pedal area mounted on a bracket with a plunger stud that rest on the brake pedal's arm the pad is attached to

May 08, 2010 | 1996 GMC Sierra

1 Answer

When should you change the timing belt of a 2003 GMC Sierra?


There is no timing belt on this engine.It has a timing chain.There is no service interval for this.When it jumps time,breaks,or it is worn out then replace the chain and sprockets as a kit.Hope this helps.Good luck.

Dec 29, 2009 | 2003 GMC Sierra 1500

1 Answer

1997 GMC Sierra 5.7 changed master cylinder calipers and brake pads. I have a hard pedal until I turn the truck on and the pedal goes to the floor? Is there something I am missing? I have bled the brakes...


check under your master cylinder,is there another clyinder below with one line in and one line out,if you do I found this is for the Abs to the rear,I had to replace this it was full of air,and did exactly what yours is now

Dec 06, 2009 | 2003 GMC Sierra 1500

1 Answer

I press my clutch and get no resistance and cant get into any gear? 2003 gmc sierra 8.1 4x4 2500hd 5 speed


Check fluid level in clutch master cylinder, if fluid is full then bleed clutch system.

If you still have no pedal resistance you will need a new master or slave cylinder for the clutch.

1c6f931.jpg

Oct 30, 2009 | 2003 GMC Sierra 2500HD

2 Answers

How do you bleed brakes on a 1999 GMC Sierra with ABS 2wheel drive 1500 series


The rule of thumb is to start as far away from the master cylinder as poss. so it means you start at the right rear, left rear, right front, then at last left front. There is a little a little weep bolt on each calliper it needs to be un lossened when break is fully applyed then tighten weep bolt back up pump the breaks while weep bolt is still tight then hold brake pedal down to floor lossen weep bolt till a full steam of fluid comes out tighten bolt back up, now move on to the next break calliper and repeat this same proccess till you finished. Hope this works better than r/r l/r r/f l/f lol!!!!

Mar 12, 2009 | 1999 GMC Sierra

Not finding what you are looking for?
2003 GMC Sierra Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...