Question about 2005 Jeep Wrangler

2 Answers

Turn signal and hazards wont work checked the fuses and the flasher already

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,486 Answers

Change the hazard switch.

Posted on Jul 03, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 40 Answers

Do you have a trailer wiring harness? If you do, recheck the wiring there. If that doesn't help and you have properly checked the flashers then you need to check each bulb

Posted on Jul 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The hazard back lights wont quit blinking when car is running even when i pull the fuse on a 2002 buick regal


What fuse are you pulling ?

Hazard Lamps
The hazard warning switch is part of the turn signal switch. The turn signal switch receives battery voltage at all times through the HAZARD SWITCH Fuse. When the hazard switch is placed in the HAZARD position, battery voltage is applied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher sends a turn signal flasher signal to the turn signal switch. The turn signal switch provides all of the turn lamps and turn indicators with the turn signal flasher signal, simultaneously flashing them on and off.

Turn Signal Lamps
The front turn signal lamps are made up of the front park/turn signal lamps and rear turn signal lamps. The front turn signal lamps flash with the rear turn signal lamps when a turn is initiated using the turn signal/multifunction lever. The turn signals will operate only with the ignition switch in the RUN position and will not operate during hazard flasher operation.
When the ignition is turned to the RUN position, battery voltage is supplied to the TURN SIGNAL Fuse. Battery voltage is then applied through the turn signal fuse circuit to the turn signal switch. When the turn signal switch is placed in the LH or RH position, voltage is supplied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher supplies a turn signal flasher signal to the turn signal switch. With the turn signal switch in the LH or RH position the corresponding turn signal indicator, rear turn signal, and front turn signal receive the turn signal switch signal and will flash. The front turn signals receive the turn signal switch signal from the turn signal switch via the BCM. The turn lamps are permanently grounded.

Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column - Tilt.

Feb 11, 2017 | Buick Cars & Trucks

2 Answers

Turn singles and hazards are not working on my 2001 deville


I would replace the turn signal hazard combo switch.

Nov 28, 2016 | Cars & Trucks

1 Answer

Turn signals wont work but flasher an lights come on


If the hazard flasher is working but the turn signals aren't, the problem is most likely either fuse A11 or the #2 relay in the trunk fuse block. However, if these check out, the problem could be either the turn/hazard switch assembly or the turn flasher module.

If both the turn signals and hazard flasher are not working, the most likely problem is the turn/hazard switch assembly.

May 26, 2015 | 1994 Cadillac DeVille

1 Answer

The turn signals and hazzard lights wont work on my 99 saturn car


Try replacing the signal & hazard flashers. Some vehicles only use 1 flasher for both. The flashers are usually located under the dash by the steering column. They look the picture below ..



2_6_2012_7_15_23_pm.jpg

Feb 06, 2012 | 1999 Saturn SL

1 Answer

Turn signals won't come on inside or outside of car but hazard lights come on inside and outside of car


Check turn signal fuse, if fuse is good, check turn signal flasher, this is identical to hazard flasher, I believe on the 1997 it is located under the dash near the center console. The turn signal and hazard flashers are the same part number so try switching places with them and see if the turn signals work. If turn signals work after switching them you need a flasher.

Nov 09, 2009 | 1997 Chevrolet Camaro

3 Answers

Turn signals wont work fuses are good?


the hazard switch above the radio is your problem. if you put on your signals and they don't flash turn hazards on then off and they will flash. (changing this *** will fix your problem

Aug 30, 2009 | 1999 Pontiac Grand Am GT

1 Answer

Haz flashers wont work but blinkers do


There are 2 seperate flashers 1 for turn signals and 1 for hazard.The hazard flasher is located in the convenance center the turn flasher in the fuse box. Also seperate fuse's for each. One battery circuit for hazard Ignition for turn signals.Check fuse for hazard,if good try swapping in the turn signal flasher and see if hazards work.They use the same flasher unit.

Aug 20, 2009 | 1993 GMC Safari

1 Answer

Turn signals wont work but flashers do


Hi.
On your 98 Dakota.
Is equipaded with a single Flasher.
If you replace all ready.
Check the FUSE # 10, 15 amp..
On the Fuse box. left side of Dash.
and the FUSE D 25, amp. On engine compartment Fuse box.
Check the proper funtion of the HAZARD switch.
Bacause if the Hazard switch is bad the turn signal don't will work. Match the OLD flasher with the New one.

If after of this still not work.
Remove the steering wheel cover, locate the Turn signal switch connector and with a TEST Light check power with the Key ON
12v. to the RED wire and PINK wire..
If you found 12v. check the connection with the switch.
If the connection is good. you will need to replace the turn signal switch.
But if you don't found 12v. You need to look a an open circuit.
And fix it..

I hope this help on your problem..
Thank you for use fixya...

Aug 31, 2008 | 1998 Dodge Dakota

Not finding what you are looking for?
2005 Jeep Wrangler Logo

380 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...